Lingshan Kong
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Lingshan Kong has a total of 15 co-authors. Here are the top co-authors by number of shared publications:
- Chirn Chye Boon
Nanyang Technological University
4 shared publications - Chenyang Li
VIRTUS, School of Electrical and Electronic Engineering, Nanyang Technological University, Singapore
2 shared publications - Kaituo Yang
VIRTUS, School of Electrical and Electronic Engineering, Nanyang Technological University, Singapore
2 shared publications Ao Zhou
VIRTUS, School of Electrical and Electronic Engineering, Nanyang Technological University, Singapore
1 shared publication- Hang Liu
Engineering Product Development Pillar, Singapore University of Technology and Design, Singapore 487372
1 shared publication Haohong Yu
Nanyang Technological University, Singapore
1 shared publication
Latest Publications
- Open Access
- 15 November 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 9, 154136-154142
A 20–80 MHz Continuously Tunable Gm-C Low-Pass Filter for Ultra-Low Power WBAN Receiver Front-End
This paper presents a third-order Butterworth low-pass filter (LPF) with continuously tuning capability to be used in the receiver front-end for Wireless Body Area Network (WBAN). To realize the bandwidth tuning for multi-standard operation in WBAN receivers with ultra-low power consumption and minimized area, a novel transconductor-capacitor (Gm-C) filter is proposed. The proposed transconductor core uses an additional gain stage with regulated cascode structure to control the transconductance ( $G_{m}$ ) by tuning the drain-source voltage $V_{ds}$ of the input transistors operating in linear region. Based on fundamental analysis, $V_{ds}$ should be reduced to attenuate the nonlinear effects caused by higher-order harmonic components. This proposed transconductor circuit enables the $G_{m}$ tuning and widens the tuning range while maintaining good linearity with negligible power and area consumption. This work is then implemented into a third-order Butterworth LPF. Measurements show that with external control voltage varying from 450 mV to 550 mV, the cutoff frequency of the LPF can be continuously adjusted from 20 MHz to 80 MHz. This design is implemented in 40 nm CMOS process with 1.1 V supply voltage. The total power consumption of this work is below 2 mW with an active area of 0.0105 mm 2 . Its low power consumption and good area efficiency makes this LPF suitable for WBAN applications.
- 15 November 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 9, 154136-154142
Open AccessA 20–80 MHz Continuously Tunable Gm-C Low-Pass Filter for Ultra-Low Power WBAN Receiver Front-End
This paper presents a third-order Butterworth low-pass filter (LPF) with continuously tuning capability to be used in the receiver front-end for Wireless Body Area Network (WBAN). To realize the bandwidth tuning for multi-standard operation in WBAN receivers with ultra-low power consumption and minimized area, a novel transconductor-capacitor (Gm-C) filter is proposed. The proposed transconductor core uses an additional gain stage with regulated cascode structure to control the transconductance ( $G_{m}$ ) by tuning the drain-source voltage $V_{ds}$ of the input transistors operating in linear region. Based on fundamental analysis, $V_{ds}$ should be reduced to attenuate the nonlinear effects caused by higher-order harmonic components. This proposed transconductor circuit enables the $G_{m}$ tuning and widens the tuning range while maintaining good linearity with negligible power and area consumption. This work is then implemented into a third-order Butterworth LPF. Measurements show that with external control voltage varying from 450 mV to 550 mV, the cutoff frequency of the LPF can be continuously adjusted from 20 MHz to 80 MHz. This design is implemented in 40 nm CMOS process with 1.1 V supply voltage. The total power consumption of this work is below 2 mW with an active area of 0.0105 mm 2 . Its low power consumption and good area efficiency makes this LPF suitable for WBAN applications.
- 1 March 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 69 (6) , 2809-2821
A Wideband dB-Linear Variable-Gain Amplifier With a Compensated Negative Pseudo-Exponential Generation Technique
This article presents a wideband dB-linear variable-gain amplifier (VGA) with a compensated negative pseudo-exponential generation (C-NPEG) technique for high-speed applications. By shifting the concave and the convex function of an original negative pseudo-exponential generator (NPEG), two additional control signals are produced to manipulate two variable-gain Gilbert-cell-based amplifiers, respectively. Cascading these two stages with another variable gain stage controlled by the original NPEG, the multiplication of three different but mutually compensated control signals is realized. As a result, the dB-linear gain range of the overall VGA is extended, and the gain error is suppressed with the proposed C-NPEG technique. To further improve the VGA's gain while maintaining a wide bandwidth, a fixed-gain stage utilizing five common-source amplifiers with RC-degeneration and active feedback is implemented. Fabricated in 40-nm CMOS technology, the core circuit consumes 24.6-mA current (excluding the output buffer) under a power supply of 1.1 V and occupies an active die area of 0.038 mm 2 . The measured gain of the overall VGA varies from -34 to 17 dB, while the dB-linear gain error over the 51-dB gain range is within ±1 dB. Meanwhile, the -3-dB bandwidth is relatively constant from 7 to 8 GHz under different gain settings.
- 1 March 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 69 (6) , 2809-2821
A Wideband dB-Linear Variable-Gain Amplifier With a Compensated Negative Pseudo-Exponential Generation Technique
This article presents a wideband dB-linear variable-gain amplifier (VGA) with a compensated negative pseudo-exponential generation (C-NPEG) technique for high-speed applications. By shifting the concave and the convex function of an original negative pseudo-exponential generator (NPEG), two additional control signals are produced to manipulate two variable-gain Gilbert-cell-based amplifiers, respectively. Cascading these two stages with another variable gain stage controlled by the original NPEG, the multiplication of three different but mutually compensated control signals is realized. As a result, the dB-linear gain range of the overall VGA is extended, and the gain error is suppressed with the proposed C-NPEG technique. To further improve the VGA's gain while maintaining a wide bandwidth, a fixed-gain stage utilizing five common-source amplifiers with RC-degeneration and active feedback is implemented. Fabricated in 40-nm CMOS technology, the core circuit consumes 24.6-mA current (excluding the output buffer) under a power supply of 1.1 V and occupies an active die area of 0.038 mm 2 . The measured gain of the overall VGA varies from -34 to 17 dB, while the dB-linear gain error over the 51-dB gain range is within ±1 dB. Meanwhile, the -3-dB bandwidth is relatively constant from 7 to 8 GHz under different gain settings.
- Open Access
- 1 January 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 9, 35814-35823
Wideband Variable-Gain Amplifiers Based on a Pseudo-Current-Steering Gain-Tuning Technique
This paper reports two variable-gain amplifiers (VGAs) featuring a new pseudo-current-steering gain-tuning technique. In the first VGA (VGA-I), a single-voltage-controlled dual-branch current mirror is developed as a standalone gain control block. In the second VGA (VGA-II), two NMOS transistors, which are biased by a tunable voltage, are integrated into a conventional common-source amplifier to steer away from a part of the total current. Meanwhile, the theoretical analysis is developed to reveal the mechanism of different gain tuning. Fabricated in a 40-nm CMOS process, VGA-I (VGA-II) occupies a tiny area of 0.03 mm 2 (0.024 mm 2 ) and consumes 22 mW (20 mW). Measured over a gain range of >64 dB, the -3-dB bandwidth of VGA-I (VGA-II) is 9 GHz (6.6 GHz). For the time-domain tests, VGA-I (VGA-II) exhibits a jitter of 40 ps (30 ps), under a 2 7 -1 PRBS input at 12 Gb/s. Their power efficiencies (1.83 and 1.67 pJ/bit) compare favorably with state-of-the-art.
- 1 January 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 9, 35814-35823
Open AccessWideband Variable-Gain Amplifiers Based on a Pseudo-Current-Steering Gain-Tuning Technique
This paper reports two variable-gain amplifiers (VGAs) featuring a new pseudo-current-steering gain-tuning technique. In the first VGA (VGA-I), a single-voltage-controlled dual-branch current mirror is developed as a standalone gain control block. In the second VGA (VGA-II), two NMOS transistors, which are biased by a tunable voltage, are integrated into a conventional common-source amplifier to steer away from a part of the total current. Meanwhile, the theoretical analysis is developed to reveal the mechanism of different gain tuning. Fabricated in a 40-nm CMOS process, VGA-I (VGA-II) occupies a tiny area of 0.03 mm 2 (0.024 mm 2 ) and consumes 22 mW (20 mW). Measured over a gain range of >64 dB, the -3-dB bandwidth of VGA-I (VGA-II) is 9 GHz (6.6 GHz). For the time-domain tests, VGA-I (VGA-II) exhibits a jitter of 40 ps (30 ps), under a 2 7 -1 PRBS input at 12 Gb/s. Their power efficiencies (1.83 and 1.67 pJ/bit) compare favorably with state-of-the-art.
- 28 May 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems I: Regular Papers
- Vol. 67 (12) , 4187-4198
Design of a Wideband Variable-Gain Amplifier With Self-Compensated Transistor for Accurate dB-Linear Characteristic in 65 nm CMOS Technology
A simple yet effective approach for variable-gain amplifier (VGA) design with accurate dB-linear characteristic is presented. In order to extend the bandwidth of the designed VGA with a minimized footprint, an inductorless-based approach is adopted. Moreover, a unique approach that exploits a self-compensated transistor to compensate dB-linear gain error is proposed. Consequently, the overall VGA has an accurate dB-linear inherent characteristic without using any additional exponential generator for gain control. To prove the concept, the designed VGA is fabricated in a standard 65 nm CMOS technology. The measured results show that the voltage gain of the designed VGA can be controlled from -19 dB to 21 dB with a gain error less than 1 dB. Meanwhile, more than 4 GHz of bandwidth can be achieved for the entire gain range. The power consumption of the VGA, excluding the output buffer, is 3.9 mW. The core circuit of this design only occupies an area of 0.012 mm².
- 28 May 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems I: Regular Papers
- Vol. 67 (12) , 4187-4198
Design of a Wideband Variable-Gain Amplifier With Self-Compensated Transistor for Accurate dB-Linear Characteristic in 65 nm CMOS Technology
A simple yet effective approach for variable-gain amplifier (VGA) design with accurate dB-linear characteristic is presented. In order to extend the bandwidth of the designed VGA with a minimized footprint, an inductorless-based approach is adopted. Moreover, a unique approach that exploits a self-compensated transistor to compensate dB-linear gain error is proposed. Consequently, the overall VGA has an accurate dB-linear inherent characteristic without using any additional exponential generator for gain control. To prove the concept, the designed VGA is fabricated in a standard 65 nm CMOS technology. The measured results show that the voltage gain of the designed VGA can be controlled from -19 dB to 21 dB with a gain error less than 1 dB. Meanwhile, more than 4 GHz of bandwidth can be achieved for the entire gain range. The power consumption of the VGA, excluding the output buffer, is 3.9 mW. The core circuit of this design only occupies an area of 0.012 mm².