Xin Hou

Ion beam-assisted deposition (IBAD) has been proposed as a promising texturing technology that uses the film epitaxy method to obtain biaxial texture on a non-textured metal or compound substrate. Magnesium oxide (MgO) is the most well explored texturing material. In order to obtain the optimal biaxial texture, the actual thickness of the IBAD-MgO film must be controlled within 12nm. Due to the bombardment of ion beams, IBAD-MgO has large lattice deformation, poor texture, and many defects in the films. In this work, the solution deposition planarization (SDP) method was used to deposit oxide amorphous Y₂O₃ films on the surface of Hastelloy C276 tapes instead of the electrochemical polishing, sputtering-Al₂O₃ and sputtering-Y₂O₃ in the commercialized buffer layer. An additional homogeneous epitaxy MgO (epi-MgO) layer, which was used to improve the biaxial texture in the IBAD-MgO layer, was deposited on the IBAD-MgO layer by electron-beam evaporation. The effects of growth temperature, film thickness, deposition rate, and oxygen pressure on the texture and morphology of the epi-MgO film were systematically studied. The best full width at half maximum (FWHM) values were 2.2° for the out-of-plane texture and 4.8° for the in-plane texture for epi-MgO films, respectively. Subsequently, the LaMnO₃ cap layer and YBa₂Cu₃O₇-x (YBCO) functional layer were deposited on the epi-MgO layer to test the quality of the MgO layer. Finally, the critical current density of the YBCO films was 6 MA/cm² (77 K, 500 nm, self-field), indicating that this research provides a high-quality MgO substrate for the YBCO layer.

Ion beam-assisted deposition (IBAD) has been proposed as a promising texturing technology that uses film epitaxy method to obtain biaxial texture on a non-textured metal or compound substrate. Magnesium oxide (MgO) is the most well explored texturing material. In order to obtain the optimal biaxial texture, the actual thickness of the IBAD-MgO film must be controlled within 12 nm. Due to the bombardment of ion beams, IBAD-MgO has large lattice deformation, poor texture and many defects in the films. In this work, an additional homogeneous epitaxy MgO (epi-MgO) layer has been deposited on the IBAD-MgO layer by electron-beam evaporation. The biaxial texture can be optimized by the deposition of additional epi-MgO layer. The effects of growth temperature, film thickness, deposition rate and oxygen flux on the texture and morphology of the epi-MgO film were systematically studied. After the research of epi-MgO process, the best full width at half maximum (FWHM) values were 2.2 for the out-of-plane texture and 4.8° for the in-plane texture, respectively. Subsequently, the LaMnO3 cap layer and YBa2Cu3O7-x (YBCO) functional layer was deposited on the epi-MgO layer to test the quality of MgO layer. Finally, the critical current density of YBCO films is 6MA/cm2 (77K, 500nm, self-field), indicating that this research provides a high-quality MgO substrate for the YBCO layer.

Objective: The objective of this study was to investigate the use of the nanocapsule sequential delivery of BMP-2 and SDF-1α through the peripheral circulatory system to promote the healing of osteoporotic fractures. Methods: Based on increased vascular permeability in the early hematoma environment around the fracture and the presence of a large number of matrix metalloproteinase MMPs in the inflammatory environment, we designed MMP-sensitive nanocapsules which were formed viain situ free-radical polymerization on the surface of grow factors with 2-(methacryloyloxy) ethyl phosphorylcholine (MPC) and the bisacryloylated VPLGVRTK peptide. The antiphagic effect and biological activity of the growth factors for the nanomicrocapsule delivery system were tested by cell experiments. The 36 SD rats with an osteoporotic fracture model were randomly divided into six groups (A, B, C, D, E, and F). In this paper, the nanocapsules loaded with BMP-2 and SDF-1 are represented as n (BMP-2) and n (SDF-1α). In the six groups, the following different combinations of growth factors were injected into the bone defect site on days 1 and 3 after bone defect surgery: in group A, n (SDF-1α) combined with n (SDF-1α); in group B, n (BMP-2) combined with n (BMP-2); in group C, n (SDF-1α) + n (BMP-2) combined with n (SDF-1α) + n (BMP-2); in group D, n (SDF-1α) combined with n (BMP-2); in group E, n (BMP-2) combined with n (SDF-1α); in group F, nanocapsules without growth factor were used as the control group. Micro-CT was used to observe the effect of n(BMP-2) and n(SDF-1α) sequential delivery inearly healing in osteoporotic fractures. Finally, in this study, we evaluated the safety of the nanocapsules delivery system by detecting ectopic osteogenesis and inflammatory responses in animals. Results: Nanocapsules have low toxicity and protect the integrity and biological activity of growth factors. The results confirmed that nanocapsules could still be effectively targeted to the fracture site on days 1, 3, and 7 after intravenous administration. Growth factors encapsulated in nanocapsules have better bone repair results than natural growth factors. In particular, groups C and D had the best bone repair results than other groups.In vivo experiments confirmed that nanocapsules did not cause significant ectopic osteogenesis and inflammation. Conclusion: The results confirmed that the special vascular permeability and inflammatory factor microenvironment of the fracture site could be used to deliver two growth factors with a synergistic effect through venous circulation, which could better promote the healing process of osteoporotic fracture.

High-efficiency deep-blue organic light-emitting diodes (OLEDs) play a crucial role in realizing ultra-high-definition (UHD) flat-panel displays and reducing power consumption. Generally, most reported OLEDs with a Commission Internationale de L’Eclairage (CIE) y coordinate < 0.06 are achieved by traditional fluorescent deep-blue emitters. However, it is challenging to obtain deep-blue fluorescent OLEDs with a high external quantum efficiency (EQE) (reaching the theoretical limit of 5%). In this work, we have successfully employed a hole-transporting material for an emitter, which can increase the efficiency in deep-blue OLEDs. The device employed with the proposed hole-transporting material exhibits deep-blue emission peaks at 427.0 nm with CIE coordinates of (0.155, 0.051), a turn-on voltage (Von) of 4.5 V, and an EQE of 4.5%. The performance of the OLED can be improved by 5.0% by optimizing the device structure. Finally, the flexible display when using the OLED devices exhibited a high image quality.

Traditional injectable hydrogels have so far found it difficult to accommodate resistance to large deformation and shape-stability under cyclic deformation. Polyampholyte (PA) hydrogels exhibit resistance to large deformation, good fatigue-resistance and rapid self-healing under dynamic forces. The limitations of the preparation process result in non-injectability of polyampholyte (PA) hydrogels. Electrostatic interactions as a medium for resistance to large deformation and shape-stability after cyclic deformation in reformed injectable hydrogels has been explored in this study. The prepared hydrogels (as-prepared PA-N) were dried and smashed into microunits and then mixed with 0.9% NaCl solution to transform them into reformed hydrogels (as-reformed PA-N) via a needle to achieve injectability. The as-reformed PA-N could exhibit 913.6% elongation at break and showed shape-stability under cyclic deformation due to the efficient self-healing abilities of the microunits and the inherited structure of the prepared hydrogels, which are superior to those of current tough injectable hydrogels. Potential applications in elbow cyclic bending and frequent movement of mobile wounds have been proved in this study. Overall, the results showed that the as-reformed PA-N achieved convenient injectability with resistance to large deformation and shape-stability under cyclic deformation at the same time.