Kosuke Sato
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Kosuke Sato has a total of 44 co-authors. Here are the top co-authors by number of shared publications:
Isamu Akasaki
12 shared publicationsSatoshi Kamiyama
Department of Materials Science and Engineering, Meijo University, Nagoya 468-8502, Japan
10 shared publicationsTetsuya Takeuchi
Department of Materials Science and Engineering, Meijo University, Nagoya 468-8502, Japan
10 shared publicationsSho Iwayama
Department of Materials Science and Engineering, Meijo University, Nagoya 468-8502, Japan
9 shared publicationsKazuki Yamada
Department of Materials Science and Engineering, Meijo University, Nagoya 468-8502, Japan
8 shared publicationsYuya Ogino
8 shared publications
Latest Publications
- 8 June 2026
- Published by AIP Publishing in Applied Physics Letters
- Vol. 128 (23)
268-nm AlGaN deep-ultraviolet LEDs on AlN substrates with 280 mW output power and wall-plug efficiency above 10% at 500 mA
We report 268-nm AlGaN-based deep-ultraviolet light-emitting diodes (LEDs) grown on single-crystal AlN substrates and achieving an optical output power of 280 mW, an external quantum efficiency of 12.1%, and a wall-plug efficiency (WPE) of 10.5% at 500 mA under pulsed operation at room temperature. In sub-270-nm ultraviolet-C (UVC) LEDs on single-crystal AlN substrates, high-current WPE is still limited by insufficient current-injection efficiency and light-extraction efficiency. Here, these limitations are addressed through three complementary design elements: an O2-annealed Ni(2 nm)/Rh(100 nm) p-contact that provides ∼45% reflectance at 268 nm while reducing the forward voltage relative to a conventional Ni/Au contact; an optimized multiple-quantum-well active region incorporating a thin high-Al-content last quantum barrier before the last quantum well to redistribute radiative recombination and suppress overflow-related droop; and a hemispherical quartz lens attached to the AlN substrate backside to improve light extraction. These results demonstrate an effective design strategy for achieving high-power, high-efficiency operation in sub-270-nm UVC LEDs.
- 8 June 2026
- Published by AIP Publishing in Applied Physics Letters
- Vol. 128 (23)
268-nm AlGaN deep-ultraviolet LEDs on AlN substrates with 280 mW output power and wall-plug efficiency above 10% at 500 mA
We report 268-nm AlGaN-based deep-ultraviolet light-emitting diodes (LEDs) grown on single-crystal AlN substrates and achieving an optical output power of 280 mW, an external quantum efficiency of 12.1%, and a wall-plug efficiency (WPE) of 10.5% at 500 mA under pulsed operation at room temperature. In sub-270-nm ultraviolet-C (UVC) LEDs on single-crystal AlN substrates, high-current WPE is still limited by insufficient current-injection efficiency and light-extraction efficiency. Here, these limitations are addressed through three complementary design elements: an O2-annealed Ni(2 nm)/Rh(100 nm) p-contact that provides ∼45% reflectance at 268 nm while reducing the forward voltage relative to a conventional Ni/Au contact; an optimized multiple-quantum-well active region incorporating a thin high-Al-content last quantum barrier before the last quantum well to redistribute radiative recombination and suppress overflow-related droop; and a hemispherical quartz lens attached to the AlN substrate backside to improve light extraction. These results demonstrate an effective design strategy for achieving high-power, high-efficiency operation in sub-270-nm UVC LEDs.
- 6 March 2023
- Published by AIP Publishing in Applied Physics Letters
- Vol. 122 (10) , 101103
Milliwatt-power sub-230-nm AlGaN LEDs with >1500 h lifetime on a single-crystal AlN substrate with many quantum wells for effective carrier injection
We fabricated sub-230-nm (far UV-C) light emitting diodes (LEDs) on a single-crystal AlN substrate. With 20 quantum well cycles implemented to enhance carrier injection into the active layers, over 1-mW output power (1.4 and 3.1 mW for 226- and 229-nm LEDs, respectively) was obtained under 100-mA operation. The maximum output power reached 21.1 mW for the single-chip 229-nm LED operating at 700 mA, without significant drooping. The forward voltage for both sub-230-nm LEDs operating at 100 mA was low (5.9 V) due to their low resistances and ideal Ohmic contacts between metal and semiconductor components. Additionally, wall plug efficiencies were 0.24% and 0.53% for the 226- and 229-nm LEDs, respectively. The lifetime of the 226-nm LED while operating at 25 °C reached over 1500 h and did not show current leakage, even after 1524 h. This long lifetime will be achieved by improving carrier injection due to many quantum wells, using a high-quality AlN substrate and achieving high wall plug efficiency.
- 6 March 2023
- Published by AIP Publishing in Applied Physics Letters
- Vol. 122 (10) , 101103
Milliwatt-power sub-230-nm AlGaN LEDs with >1500 h lifetime on a single-crystal AlN substrate with many quantum wells for effective carrier injection
We fabricated sub-230-nm (far UV-C) light emitting diodes (LEDs) on a single-crystal AlN substrate. With 20 quantum well cycles implemented to enhance carrier injection into the active layers, over 1-mW output power (1.4 and 3.1 mW for 226- and 229-nm LEDs, respectively) was obtained under 100-mA operation. The maximum output power reached 21.1 mW for the single-chip 229-nm LED operating at 700 mA, without significant drooping. The forward voltage for both sub-230-nm LEDs operating at 100 mA was low (5.9 V) due to their low resistances and ideal Ohmic contacts between metal and semiconductor components. Additionally, wall plug efficiencies were 0.24% and 0.53% for the 226- and 229-nm LEDs, respectively. The lifetime of the 226-nm LED while operating at 25 °C reached over 1500 h and did not show current leakage, even after 1524 h. This long lifetime will be achieved by improving carrier injection due to many quantum wells, using a high-quality AlN substrate and achieving high wall plug efficiency.
- 16 March 2022
- Published by IOP Publishing in Japanese Journal of Applied Physics
- Vol. 61 (4) , 040501
Recent development of UV-B laser diodes
This review paper describes the historical development, current issues, and future expectations of UV-B laser diodes, which are expected to be adopted in various applications such as in microfabrication and biotechnology in the near future. To achieve RT operation of UV-B laser diodes, several challenges need to be addressed, including the development of a crystal growth technique for high-crystalline-quality AlGaN films that enables laser oscillation with a low excitation carrier density, and the development of a semiconductor layer structure for simultaneous formation of a desirable optical cavity and injection of high-density carriers (operation of high current density), allowing laser oscillation in the active layer. These challenges and the corresponding technologies that have overcome them are reviewed. The current status of device characteristics and future challenges are also discussed.
- 16 March 2022
- Published by IOP Publishing in Japanese Journal of Applied Physics
- Vol. 61 (4) , 040501
Recent development of UV-B laser diodes
This review paper describes the historical development, current issues, and future expectations of UV-B laser diodes, which are expected to be adopted in various applications such as in microfabrication and biotechnology in the near future. To achieve RT operation of UV-B laser diodes, several challenges need to be addressed, including the development of a crystal growth technique for high-crystalline-quality AlGaN films that enables laser oscillation with a low excitation carrier density, and the development of a semiconductor layer structure for simultaneous formation of a desirable optical cavity and injection of high-density carriers (operation of high current density), allowing laser oscillation in the active layer. These challenges and the corresponding technologies that have overcome them are reviewed. The current status of device characteristics and future challenges are also discussed.
- 1 September 2021
- Published by IOP Publishing in Applied Physics Express
- Vol. 14 (9) , 094009
Low-threshold-current (~85 mA) of AlGaN-based UV-B laser diode with refractive-index waveguide structure
- 1 September 2021
- Published by IOP Publishing in Applied Physics Express
- Vol. 14 (9) , 094009
Low-threshold-current (~85 mA) of AlGaN-based UV-B laser diode with refractive-index waveguide structure
- 27 August 2021
- Published by IOP Publishing in Applied Physics Express
- Vol. 14 (9) , 096503
Effects of Mg dopant in Al-composition-graded Al x Ga1−x N (0.45 ≤ x) on vertical electrical conductivity of ultrawide bandgap AlGaN p–n junction
- 27 August 2021
- Published by IOP Publishing in Applied Physics Express
- Vol. 14 (9) , 096503
Effects of Mg dopant in Al-composition-graded Al x Ga1−x N (0.45 ≤ x) on vertical electrical conductivity of ultrawide bandgap AlGaN p–n junction
- 14 June 2021
- Published by IOP Publishing in Japanese Journal of Applied Physics
- Vol. 60 (7) , 074002
Analysis of carrier injection efficiency of AlGaN UV-B laser diodes based on the relationship between threshold current density and cavity length
The carrier injection efficiency η i of recently developed UV-B laser diodes (LDs) is estimated on the basis of fundamental calculations and measurements. A general procedure to estimate η i based on the relationship between the differential external quantum efficiency and the cavity length proves to be inadequate because of the large variation. To estimate η i without relying on the unstable output power, we analyze in detail how the threshold current density relates to the cavity length. By applying a light confinement factor of 3.5%, an internal loss of 10 cm −1 , a current density of 0.56 kA cm −2 in the emission layers at zero gain, and a reflectivity of the mirror facet of 0.16, we estimate η i ≈ 3.5% for UV-B LDs. This low η i in UV-B LDs is due to unbalanced injection between electron and hole currents, which leads to electron overflow to the p-GaN side, as indicated by a simulation.
- 14 June 2021
- Published by IOP Publishing in Japanese Journal of Applied Physics
- Vol. 60 (7) , 074002
Analysis of carrier injection efficiency of AlGaN UV-B laser diodes based on the relationship between threshold current density and cavity length
The carrier injection efficiency η i of recently developed UV-B laser diodes (LDs) is estimated on the basis of fundamental calculations and measurements. A general procedure to estimate η i based on the relationship between the differential external quantum efficiency and the cavity length proves to be inadequate because of the large variation. To estimate η i without relying on the unstable output power, we analyze in detail how the threshold current density relates to the cavity length. By applying a light confinement factor of 3.5%, an internal loss of 10 cm −1 , a current density of 0.56 kA cm −2 in the emission layers at zero gain, and a reflectivity of the mirror facet of 0.16, we estimate η i ≈ 3.5% for UV-B LDs. This low η i in UV-B LDs is due to unbalanced injection between electron and hole currents, which leads to electron overflow to the p-GaN side, as indicated by a simulation.
- 27 April 2021
- Published by IOP Publishing in Applied Physics Express
- Vol. 14 (5) , 055505
AlGaN-based UV-B laser diode with a wavelength of 290 nm on 1 μm periodic concavo–convex pattern AlN on a sapphire substrate
Room-temperature pulsed oscillation with a laser wavelength of 290 nm and a threshold current density of 35 kA cm−2 was achieved by fabricating a UV-B laser diode on a thick AlGaN film formed on a 1 μm periodic concavo–convex pattern AlN (PCCP-AlN) on a sapphire substrate. The advantage of this method using PCCP-AlN is that it promotes the nucleation of AlGaN crystals. Planarization of this growth nucleus with AlGaN reduces the threading dislocation density at the top of the AlGaN growth layer while suppressing the formation of giant micrometer-sized hillocks and V-shaped pits that appear irregularly.
- 27 April 2021
- Published by IOP Publishing in Applied Physics Express
- Vol. 14 (5) , 055505
AlGaN-based UV-B laser diode with a wavelength of 290 nm on 1 μm periodic concavo–convex pattern AlN on a sapphire substrate
Room-temperature pulsed oscillation with a laser wavelength of 290 nm and a threshold current density of 35 kA cm−2 was achieved by fabricating a UV-B laser diode on a thick AlGaN film formed on a 1 μm periodic concavo–convex pattern AlN (PCCP-AlN) on a sapphire substrate. The advantage of this method using PCCP-AlN is that it promotes the nucleation of AlGaN crystals. Planarization of this growth nucleus with AlGaN reduces the threading dislocation density at the top of the AlGaN growth layer while suppressing the formation of giant micrometer-sized hillocks and V-shaped pits that appear irregularly.
- 19 April 2021
- Published by AIP Publishing in Applied Physics Letters
- Vol. 118 (16) , 163504
AlGaN-based UV-B laser diode with a high optical confinement factor
To reduce the threshold current density (Jth) of ultraviolet (UV)-B AlGaN-based laser diodes, we investigated the critical parameters aiming to increase the injection efficiency ηi and the optical confinement factor Γ. Optimization of the thickness of the waveguide layer, the average Al content of the p-type AlGaN cladding layer, and the film thickness of the cladding layer demonstrated that the device characteristics can be improved. This optimization achieved a reduction in Jth to 13.3 kA cm−2 at a lasing wavelength of 300 nm, thus offering the lowest Jth value yet achieved for a UV-B laser diode.
- 19 April 2021
- Published by AIP Publishing in Applied Physics Letters
- Vol. 118 (16) , 163504
AlGaN-based UV-B laser diode with a high optical confinement factor
To reduce the threshold current density (Jth) of ultraviolet (UV)-B AlGaN-based laser diodes, we investigated the critical parameters aiming to increase the injection efficiency ηi and the optical confinement factor Γ. Optimization of the thickness of the waveguide layer, the average Al content of the p-type AlGaN cladding layer, and the film thickness of the cladding layer demonstrated that the device characteristics can be improved. This optimization achieved a reduction in Jth to 13.3 kA cm−2 at a lasing wavelength of 300 nm, thus offering the lowest Jth value yet achieved for a UV-B laser diode.
- 29 June 2020
- Published by IOP Publishing in Applied Physics Express
- Vol. 13 (7) , 071008
Internal loss of AlGaN-based ultraviolet-B band laser diodes with p-type AlGaN cladding layer using polarization doping
- 29 June 2020
- Published by IOP Publishing in Applied Physics Express
- Vol. 13 (7) , 071008
Internal loss of AlGaN-based ultraviolet-B band laser diodes with p-type AlGaN cladding layer using polarization doping
- 1 April 2020
- Published by Elsevier in Journal of Crystal Growth
- Vol. 535
Effects of Mg and Si doping in the guide layers of AlGaN-based ultraviolet-B band lasers
- 1 April 2020
- Published by Elsevier in Journal of Crystal Growth
- Vol. 535
Effects of Mg and Si doping in the guide layers of AlGaN-based ultraviolet-B band lasers