Alin Constantin Murariu has a total of 66 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Failure Analysis in Resistance Welded Automotive Components

    by Ion Aurel Perianu, Alin Murariu, Iuliana Duma, Radu Popescu, Raluca Faur, Baeră Cornelia, Ion Dragoş Uţu, Marco Brand, Ovidiu Florin Cornea, Cristian Andrei Cornea

    This case study focuses on the laboratory examination and material analysis of welded components in automotive production. The investigation included metallographic analyses, microstructural evaluations, and non-destructive testing methods to assess weld integrity. Key issues identified were the presence of thermal distortions, incomplete welds, and material defects such as micro-cracks and porosity. A detailed metallographic study revealed that improper cooling rates significantly affected the heat-affected zone (HAZ) and weld microstructure, leading to weaknesses in material strength and increased susceptibility to fatigue. Variations in cooling water flow during the welding process were examined, showing that an intermediate cooling flow rate produced the most consistent microstructural properties. The analysis also indicated the presence of stress concentrators at weld interfaces, which may lead to premature failure under operational stresses. Recommendations include optimizing cooling rates and post-weld heat treatment to enhance material resilience, ensuring long-term durability and performance of welded assemblies.


  • Optimising the HVOF Deposition Technology of Al2O3-40%TiO2 Coatings for Energy Industry Applications

    by Alin Constantin Murariu, Ion Aurel Perianu, Marius Cocard, Eneia Frici

    The paper presents a systematic approach to optimize the HVOF deposition technology of Al 2 O 3 40 TiO 2 coatings for the protection of components in the energy industry. Key performance factors evaluated include scratch resistance, surface roughness, and friction coefficient, given their importance for the intended applications. By means of a comprehensive experimental program using the Design of Experiment (DOE) method, the main HVOF process parameters were investigated, such as Fuel-to-Oxygen ratio (F/O), Stand-off Distance (SOD), and Powder Feed Rate (PFR), to identify optimal deposition conditions. Scratch resistance tests revealed that increasing the F/O and reducing the SOD significantly improved the tribological properties of the coatings. Surface morphology analysis through optical and electron microscopy confirmed that optimized HVOF parameters lead to dense coatings with low roughness and minimal defects, essential characteristics for components subjected to wear and severe friction. Additionally, tribological measurements demonstrated a significant reduction in the coefficient of friction for the optimized coatings. The obtained results demonstrate the HVOF technology’s capability to produce Al 2 O 3 40 TiO 2 coatings with superior properties for protecting energy industry components operating under severe conditions. The presented optimization approach can serve as a guide for best practices in developing new coating systems with enhanced performance.

  • Spectroscopic Analysis of HVOF-Sprayed Al2O3-40%TiO2 Coatings for Solar Thermal Applications

    by Claudia Amalia Ciurel, Alin Constantin Murariu, Anca Lidia Borz

    This paper presents an in-depth spectroscopic analysis of Al 2 O 3 -40%TiO 2 coatings deposited via HVOF thermal spraying on a 10CrMo9.10 heat-resistant steel substrate. The study aims to correlate the optoelectronic and structural properties of the coatings with their composition and microstructure. Spectroscopic investigations revealed intense absorption in the visible (VIS) region due to electronic transitions from the valence band to the conduction band of the ceramic materials and high reflectivity in the ultraviolet (UV) region. These properties make the coatings particularly useful for protective systems in solar thermal power plants. The detailed characterization of the optical properties of the Al 2 O 3 -40%TiO 2 coatings obtained through HVOF technology was made possible by corroborating spectroscopic results. These insights are essential for understanding the mechanisms that govern the performance of these coatings in protective applications under high temperatures and aggressive environments.

  • Optimization of Hardness and Adhesion of Al2O3-40%TiO2 Coating Obtained by HVOF Spraying through Process Parameter Control

    by Vlad Ștefan Constantin, Alin Constantin Murariu, Ion Aurel Perianu, Marius Cocard, Iuliana Duma, Constantin Alin Antal

    The paper presents an optimization approach for enhancing the hardness and adhesion of Al 2 O 3 -40%TiO 2 coatings produced by High-Velocity Oxi-Fuel (HVOF) thermal spraying, aimed at their application in protecting components subjected to aggressive environments and severe mechanical stresses [1-4]. Through an experimental factorial program, key parameters of the HVOF process such as fuel flow rate, oxygen flow rate, spray distance, and powder feed rate were investigated to identify optimal conditions leading to improved mechanical performance of the deposited layers. Vickers hardness and tensile adhesion tests were utilized to evaluate the properties of the coatings. The results indicated that increasing the fuel and oxygen flow rates, coupled with reducing the spray distance, significantly increased the hardness of the coatings, achieving values up to 244 HV5. Moreover, optimizing these parameters maximized the coating-substrate adhesion, reaching values exceeding 30 MPa. Microstructural analysis using scanning electron microscopy (SEM) revealed that optimized HVOF parameters generated dense layers with low porosity and enhanced adhesion at the layer-substrate interface, thereby explaining the superior mechanical behaviors of the coatings. These findings demonstrate the capability of HVOF technology to produce Al 2 O 3 -40%TiO 2 layers with optimal mechanical properties, essential for applications requiring resistance to wear, impact, and corrosive environments [5-7].


  • Analysing Recurring Failures: Case Study of a Pressurized Gas Supply Pipeline

    by Alin Constantin Murariu, Iuliana Duma, Radu Nicolae Popescu

    This paper presents a case study of an in-service failure occurred in a pressurized gas supply pipeline, which has been recurring in recent years, particularly during the winter season. The investigation focused on two pipe coupons extracted from a DN 300 pipeline, which had sustained damage while in operation as part of a natural gas pipeline. Through the implementation of mechanical and non-destructive testing methods on the pipe couplings and their welds, multiple non-conformities were identified. These non-conformities were found to be the root causes of failures that occurred after welding and during operation. The findings of this investigation have led to several valuable comments and recommendations, which are beneficial for manufacturing companies and clients alike. Implementing these suggestions can contribute to enhanced safety and operational efficiency in gas pipeline systems.

  • Investigation the Effects of Fire on an Industrial Metallic Structure

    by Alin Constantin Murariu, Iuliana Duma, Ion Aurel Perianu

    Fires can affect both civil and industrial buildings. Following a fire affecting a building or industrial structure, inspections are normally carried out to assess how the materials used in the construction have deteriorated and the severity of this phenomena. Emphasis is put on assessing the material damage, which involves understanding the mode of degradation, the mechanical and physical characteristics of these building materials and their behaviour in the presence of a thermal source. Understanding how heat affects building materials is very useful in assessing the extent of damage to various building components. Paper presents the results of an in-depth investigation of the effect of fire on an industrial building that has suffered a fire. Conclusions are drawn on the degree of material degradation of various elements of the hall structure.

  • Advancements in Abrasive Waterjet Cutting Technologies: A Comprehensive Overview and Future Prospects in the Manufacturing Industry

    by Ion Aurel Perianu, Alin Constantin Murariu, Lia-Nicoleta Botila, Matei Marin-Corciu, Iuliana Duma, Cornelia Baeră

    The purpose of this article is to provide a comprehensive overview of the latest trends in abrasive waterjet cutting technologies and their current state of the art. The article will explore the basic principles of abrasive waterjet cutting and the process advantages and application fields. Additionally, the article will discuss the latest developments in abrasive waterjet cutting technologies, including advancements in abrasive waterjet systems, automation and control systems, and nozzle materials. It will also highlight the most advanced systems currently available and their features and capabilities, as well as provide examples of industries with specific applications that are currently using abrasive waterjet cutting technologies. Finally, the article will discuss potential future developments in abrasive waterjet cutting technologies and their potential to enhance cutting precision, speed, and efficiency, and lead to new applications. Overall, this article aims to provide a comprehensive understanding of abrasive waterjet cutting technologies and their importance in the manufacturing industry.


  • Bibliographic Study Regarding Renewable Energy: Infrared Reflective Layer Made of Al2O3 Using HVOF Process

    by Vlad-Ștefan Constantin, Alin Constantin Murariu, Ion Aurel Perianu, Iuliana Duma

    This bibliographic research explores the field of renewable energy by exploiting the potential of the High Velocity Oxygen Fuel Deposition (HVOF) method, an advanced thermal spray coating technology. HVOF involves propelling powder particles at remarkable speeds onto material surfaces, providing a means of applying protective coatings. This study explores the versatility of HVOF in creating protective coatings tailored for renewable energy applications. Specifically, the main coating targeted is the infrared reflective coating, made using alumina powders renowned for their exceptional attributes such as high strength, hardness, corrosion resistance and heat resistance, making them ideal for various components used in the renewable energy sector.

  • Numerical and Experimental Study for Al4043A Aluminium-Silicium Alloy Fabricated by Wire Arc Additive Manufacturing under Dynamic Tests

    by Sergiu Valentin Galatanu, Iuliana Duma, Cosmin Florin Popa, Alin-Constantin Murariu, Ion Aurel Perianu, Liviu Marsavina

    The paper presents an experimental investigation of the impact properties and imperfections of the 3D printed Al4043A aluminium-silicium alloy using wire-arc additive manufacturing. Using an experimental program based on factorial experiments, correlations between the main WAAM process parameters and the related properties of the deposition were determined. Charpy impact strength investigations, using standard notched specimens, were performed on an Instron CEAST 9050 instrumented Charpy impact pendulum system following the ISO 148-1 standard. During the experimental tests, the brittle behaviour of the specimens could be observed. After the experimental tests, the impact behaviour was numerically analysed, showing a relatively good correlation between the results.

  • Optimization of the Printing Parameters of Glass Fiber Reinforced PA6 Using Factorial Experiments

    by Matei Marin-Corciu, Nicuşor Alin Sîrbu, Alin-Constantin Murariu, Marius Cocard, Alexandru Adrian Geana

    Fiber-reinforced 3D printing filaments are composite materials compounded with short, chopped additives (in this paper case glass fibers) in a polymer matrix base. Engineering filaments and reinforced filaments have gotten a lot more popular in the last few years due to their capabilities and added properties given by the reinforced material. The biggest drawback reinforced materials have other than the cost is the printability. Due to the abrasive nature of glass fiber to be able to successfully print it certain modifications to the FDM equipment must be made, such as using a tempered steel nozzle. It is also recommended to print the components in a temperature-controlled room and to keep the humidity level of the material before printing as low as possible. In this paper a glass fiber reinforced PA6 filament was tested using different printing parameters (temperature, printing speed, layer height) to establish the optimal parameters for reducing the risk reinforced materials pose for the FDM equipment while also looking for the best mechanical properties of the printed parts.