Ioannis Papadimitriou
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Ioannis Papadimitriou has a total of 30 co-authors. Here are the top co-authors by number of shared publications:
- Panos Tsakiropoulos
Department of Materials Science and Engineering, Sir Robert Hadfield Building, The University of Sheffield, Mappin Street, Sheffield S1 3JD, UK
6 shared publications C. Utton
3 shared publicationsClaire Utton
Department of Materials Science and Engineering, The University of Sheffield, Sheffield, UK
3 shared publications- Gustavo Esteban-Manzanares
IMDEA Materials Institute, C/Eric Kandel 2, Getafe 28906 – Madrid, Spain
3 shared publications - Javier Llorca
IMDEA Materials Institute, Madrid, Spain
3 shared publications - Andrew J. Scott
Institute for Materials Research
2 shared publications
Latest Publications
- Top Cited PapersOpen Access
- 19 November 2025
- Published by Springer Nature in Archives of Computational Methods in Engineering
- Vol. 33 (4) , 5223-5260
Physics-Informed Neural Networks in Materials Modeling and Design: A Review
Physics-Informed Neural Networks are neural networks which combine data-driven deep learning and physical models by incorporating physical laws into their loss function. They are promising and flexible solvers or surrogates for problems governed by partial differential equations, including forward and inverse cases, and during the last few years they have been applied to a variety of problems in physics and engineering. In this survey, we present a comprehensive analysis of PINNs while focusing on their applications in materials science. We examine their foundational form and components, expand on enhancing strategies, and explore various aspects of their practical implementations. For materials modeling, problem cases are systematically organized based on the main scope of publications found in the literature. For this survey, problems are categorized into heat transfer related problems, including multiphysics cases, materials properties and design, materials durability, stress analysis, as well as problems related to porous media and multi-phase materials. Finally, we discuss the current challenges and limitations of PINNs, their advantages, and potential future research directions.
- 19 November 2025
- Published by Springer Nature in Archives of Computational Methods in Engineering
- Vol. 33 (4) , 5223-5260
Top Cited PapersOpen AccessPhysics-Informed Neural Networks in Materials Modeling and Design: A Review
Physics-Informed Neural Networks are neural networks which combine data-driven deep learning and physical models by incorporating physical laws into their loss function. They are promising and flexible solvers or surrogates for problems governed by partial differential equations, including forward and inverse cases, and during the last few years they have been applied to a variety of problems in physics and engineering. In this survey, we present a comprehensive analysis of PINNs while focusing on their applications in materials science. We examine their foundational form and components, expand on enhancing strategies, and explore various aspects of their practical implementations. For materials modeling, problem cases are systematically organized based on the main scope of publications found in the literature. For this survey, problems are categorized into heat transfer related problems, including multiphysics cases, materials properties and design, materials durability, stress analysis, as well as problems related to porous media and multi-phase materials. Finally, we discuss the current challenges and limitations of PINNs, their advantages, and potential future research directions.
- Top Cited Papers
- 21 January 2024
- Published by Elsevier in Computational Materials Science
- Vol. 235
AI methods in materials design, discovery and manufacturing: A review
- 21 January 2024
- Published by Elsevier in Computational Materials Science
- Vol. 235
Top Cited PapersAI methods in materials design, discovery and manufacturing: A review
- Open Access
- 29 September 2020
- Published by MDPI AG in Electronics
- Vol. 9 (10) , 1593
Audio-Based Event Detection at Different SNR Settings Using Two-Dimensional Spectrogram Magnitude Representations
Audio-based event detection poses a number of different challenges that are not encountered in other fields, such as image detection. Challenges such as ambient noise, low Signal-to-Noise Ratio (SNR) and microphone distance are not yet fully understood. If the multimodal approaches are to become better in a range of fields of interest, audio analysis will have to play an integral part. Event recognition in autonomous vehicles (AVs) is such a field at a nascent stage that can especially leverage solely on audio or can be part of the multimodal approach. In this manuscript, an extensive analysis focused on the comparison of different magnitude representations of the raw audio is presented. The data on which the analysis is carried out is part of the publicly available MIVIA Audio Events dataset. Single channel Short-Time Fourier Transform (STFT), mel-scale and Mel-Frequency Cepstral Coefficients (MFCCs) spectrogram representations are used. Furthermore, aggregation methods of the aforementioned spectrogram representations are examined; the feature concatenation compared to the stacking of features as separate channels. The effect of the SNR on recognition accuracy and the generalization of the proposed methods on datasets that were both seen and not seen during training are studied and reported.
- 29 September 2020
- Published by MDPI AG in Electronics
- Vol. 9 (10) , 1593
Open AccessAudio-Based Event Detection at Different SNR Settings Using Two-Dimensional Spectrogram Magnitude Representations
Audio-based event detection poses a number of different challenges that are not encountered in other fields, such as image detection. Challenges such as ambient noise, low Signal-to-Noise Ratio (SNR) and microphone distance are not yet fully understood. If the multimodal approaches are to become better in a range of fields of interest, audio analysis will have to play an integral part. Event recognition in autonomous vehicles (AVs) is such a field at a nascent stage that can especially leverage solely on audio or can be part of the multimodal approach. In this manuscript, an extensive analysis focused on the comparison of different magnitude representations of the raw audio is presented. The data on which the analysis is carried out is part of the publicly available MIVIA Audio Events dataset. Single channel Short-Time Fourier Transform (STFT), mel-scale and Mel-Frequency Cepstral Coefficients (MFCCs) spectrogram representations are used. Furthermore, aggregation methods of the aforementioned spectrogram representations are examined; the feature concatenation compared to the stacking of features as separate channels. The effect of the SNR on recognition accuracy and the generalization of the proposed methods on datasets that were both seen and not seen during training are studied and reported.
- Open Access
Phase Equilibria in the Nb-Rich Region of Al-Nb-Sn at 900 and 1200 °C
The Al-Nb-Sn phase diagram was studied experimentally in the Nb-rich region to provide important phase equilibria information for alloy design of Nb-silicide based materials for aero engine applications. Three alloys were produced: Nb-17Al-17Sn, Nb-33Al-13Sn and Nb-16Al-20Sn (at.%). As-cast and heat-treated alloys (900 and 1200 °C) were analysed using XRD (X-ray diffraction) and SEM/EDS (scanning electron microscopy/ electron dispersive x-ray spectroscopy). Tin showed a high solubility in Nb2Al, reaching up to 21 at.% in the Sn-rich areas, substituting for Al atoms. Tin and Al also substituted for each other in the A15 phases (Nb3Al and Nb3Sn). Tin showed limited solubility in NbAl3, not exceeding 3.6 at.% as it substituted Al atoms. The solubility of Al in NbSn2 varied from 4.8 to 6.8 at.%. A ternary phase, Nb5Sn2Al with the tI32 W5Si3 crystal structure, was found to be stable. This phase was observed in the 900 °C heat-treated samples, but not in the 1200 °C heated samples.
Open AccessPhase Equilibria in the Nb-Rich Region of Al-Nb-Sn at 900 and 1200 °C
The Al-Nb-Sn phase diagram was studied experimentally in the Nb-rich region to provide important phase equilibria information for alloy design of Nb-silicide based materials for aero engine applications. Three alloys were produced: Nb-17Al-17Sn, Nb-33Al-13Sn and Nb-16Al-20Sn (at.%). As-cast and heat-treated alloys (900 and 1200 °C) were analysed using XRD (X-ray diffraction) and SEM/EDS (scanning electron microscopy/ electron dispersive x-ray spectroscopy). Tin showed a high solubility in Nb2Al, reaching up to 21 at.% in the Sn-rich areas, substituting for Al atoms. Tin and Al also substituted for each other in the A15 phases (Nb3Al and Nb3Sn). Tin showed limited solubility in NbAl3, not exceeding 3.6 at.% as it substituted Al atoms. The solubility of Al in NbSn2 varied from 4.8 to 6.8 at.%. A ternary phase, Nb5Sn2Al with the tI32 W5Si3 crystal structure, was found to be stable. This phase was observed in the 900 °C heat-treated samples, but not in the 1200 °C heated samples.
- 18 July 2019
- Published by IOP Publishing in Modelling and Simulation in Materials Science and Engineering
- Vol. 27 (7) , 075003
Basal dislocation/precipitate interactions in Mg–Al alloys: an atomistic investigation
The interaction between edge basal dislocations and β -Mg 17 Al 12 precipitates was studied using atomistic simulations. A strategy was developed to insert a lozenge-shaped Mg 17 Al 12 precipitate with Burgers orientation relationship within the Mg matrix in an atomistic model ensuring that the matrix/precipitate interfaces were close to minimum energy configurations. It was found that the dislocation bypassed the precipitate by the formation of an Orowan loop that entered the precipitate. Within the precipitate, the dislocation was not able to progress further until more dislocations overcome the precipitate and push the initial loop to shear the precipitate along the (110) plane, parallel to the basal plane of Mg. This process was eventually repeated as more dislocations overcome the precipitate and this mechanism of dislocation/precipitate interaction was in agreement with experimental observations. Moreover, the initial resolved shear stress to bypass the precipitate was in agreement with the predictions of the Bacon–Kocks–Scattergood model.
- 18 July 2019
- Published by IOP Publishing in Modelling and Simulation in Materials Science and Engineering
- Vol. 27 (7) , 075003
Basal dislocation/precipitate interactions in Mg–Al alloys: an atomistic investigation
The interaction between edge basal dislocations and β -Mg 17 Al 12 precipitates was studied using atomistic simulations. A strategy was developed to insert a lozenge-shaped Mg 17 Al 12 precipitate with Burgers orientation relationship within the Mg matrix in an atomistic model ensuring that the matrix/precipitate interfaces were close to minimum energy configurations. It was found that the dislocation bypassed the precipitate by the formation of an Orowan loop that entered the precipitate. Within the precipitate, the dislocation was not able to progress further until more dislocations overcome the precipitate and push the initial loop to shear the precipitate along the (110) plane, parallel to the basal plane of Mg. This process was eventually repeated as more dislocations overcome the precipitate and this mechanism of dislocation/precipitate interaction was in agreement with experimental observations. Moreover, the initial resolved shear stress to bypass the precipitate was in agreement with the predictions of the Bacon–Kocks–Scattergood model.
- 1 September 2018
- Published by Elsevier in Journal of the Mechanics and Physics of Solids
- Vol. 118, 228-244
Discrete dislocation dynamics simulations of dislocation-θ′ precipitate interaction in Al-Cu alloys
- 1 September 2018
- Published by Elsevier in Journal of the Mechanics and Physics of Solids
- Vol. 118, 228-244
Discrete dislocation dynamics simulations of dislocation-θ′ precipitate interaction in Al-Cu alloys
- 1 August 2018
- Published by Elsevier in Journal of Alloys and Compounds
- Vol. 757, 504-519
A multidisciplinary approach to study precipitation kinetics and hardening in an Al-4Cu (wt. %) alloy
- 1 August 2018
- Published by Elsevier in Journal of Alloys and Compounds
- Vol. 757, 504-519
A multidisciplinary approach to study precipitation kinetics and hardening in an Al-4Cu (wt. %) alloy
- Open Access
- 1 December 2017
- Published by Elsevier in Journal of Manufacturing Processes
- Vol. 30, 195-207
Joining TWIP to TWIP and TWIP to aluminium: A comparative study between joining processes, joint properties and mechanical performance
- 1 December 2017
- Published by Elsevier in Journal of Manufacturing Processes
- Vol. 30, 195-207
Open AccessJoining TWIP to TWIP and TWIP to aluminium: A comparative study between joining processes, joint properties and mechanical performance
- Open Access
- 1 September 2017
- Published by Elsevier in Journal of Alloys and Compounds
- Vol. 717, 303-316
Experimental and thermodynamic assessment of the Ge-Nb-Si ternary phase diagram
- 1 September 2017
- Published by Elsevier in Journal of Alloys and Compounds
- Vol. 717, 303-316
Open AccessExperimental and thermodynamic assessment of the Ge-Nb-Si ternary phase diagram
- Open Access
- 10 July 2017
- Published by Taylor & Francis in Science and Technology of Advanced Materials
- Vol. 18 (1) , 467-479
The impact of Ti and temperature on the stability of Nb5Si3 phases: a first-principles study
Nb-silicide based alloys could be used at T > 1423 K in future aero-engines. Titanium is an important additive to these new alloys where it improves oxidation, fracture toughness and reduces density. The microstructures of the new alloys consist of an Nb solid solution, and silicides and other intermetallics can be present. Three Nb5Si3 polymorphs are known, namely αNb5Si3 (tI32 Cr5B3-type, D8l), βNb5Si3 (tI32 W5Si3-type, D8m) and γNb5Si3 (hP16 Mn5Si3-type, D88). In these 5–3 silicides Nb atoms can be substituted by Ti atoms. The type of stable Nb5Si3 depends on temperature and concentration of Ti addition and is important for the stability and properties of the alloys. The effect of increasing concentration of Ti on the transition temperature between the polymorphs has not been studied. In this work first-principles calculations were used to predict the stability and physical properties of the various Nb5Si3 silicides alloyed with Ti. Temperature-dependent enthalpies of formation were computed, and the transition temperature between the low (α) and high (β) temperature polymorphs of Nb5Si3 was found to decrease significantly with increasing Ti content. The γNb5Si3 was found to be stable only at high Ti concentrations, above approximately 50 at. % Ti. Calculation of physical properties and the Cauchy pressures, Pugh’s index of ductility and Poisson ratio showed that as the Ti content increased, the bulk moduli of all silicides decreased, while the shear and elastic moduli and the Debye temperature increased for the αNb5Si3 and γNb5Si3 and decreased for βNb5Si3. With the addition of Ti the αNb5Si3 and γNb5Si3 became less ductile, whereas the βNb5Si3 became more ductile. When Ti was added in the αNb5Si3 and βNb5Si3 the linear thermal expansion coefficients of the silicides decreased, but the anisotropy of coefficient of thermal expansion did not change significantly.
- 10 July 2017
- Published by Taylor & Francis in Science and Technology of Advanced Materials
- Vol. 18 (1) , 467-479
Open AccessThe impact of Ti and temperature on the stability of Nb5Si3 phases: a first-principles study
Nb-silicide based alloys could be used at T > 1423 K in future aero-engines. Titanium is an important additive to these new alloys where it improves oxidation, fracture toughness and reduces density. The microstructures of the new alloys consist of an Nb solid solution, and silicides and other intermetallics can be present. Three Nb5Si3 polymorphs are known, namely αNb5Si3 (tI32 Cr5B3-type, D8l), βNb5Si3 (tI32 W5Si3-type, D8m) and γNb5Si3 (hP16 Mn5Si3-type, D88). In these 5–3 silicides Nb atoms can be substituted by Ti atoms. The type of stable Nb5Si3 depends on temperature and concentration of Ti addition and is important for the stability and properties of the alloys. The effect of increasing concentration of Ti on the transition temperature between the polymorphs has not been studied. In this work first-principles calculations were used to predict the stability and physical properties of the various Nb5Si3 silicides alloyed with Ti. Temperature-dependent enthalpies of formation were computed, and the transition temperature between the low (α) and high (β) temperature polymorphs of Nb5Si3 was found to decrease significantly with increasing Ti content. The γNb5Si3 was found to be stable only at high Ti concentrations, above approximately 50 at. % Ti. Calculation of physical properties and the Cauchy pressures, Pugh’s index of ductility and Poisson ratio showed that as the Ti content increased, the bulk moduli of all silicides decreased, while the shear and elastic moduli and the Debye temperature increased for the αNb5Si3 and γNb5Si3 and decreased for βNb5Si3. With the addition of Ti the αNb5Si3 and γNb5Si3 became less ductile, whereas the βNb5Si3 became more ductile. When Ti was added in the αNb5Si3 and βNb5Si3 the linear thermal expansion coefficients of the silicides decreased, but the anisotropy of coefficient of thermal expansion did not change significantly.