СЦСергій Цвіркун

Сергій Цвіркун

*This is an algorithmically generated author record based on publicly available information.

Сергій Цвіркун has a total of 15 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    ДЕЯКІ ОСОБЛИВОСТІ ВИКОРИСТАННЯ ЕЛЕМЕНТІВ ТРИБОМЕХАНІКИ ПРИ ПРОЕКТУВАННІ ТА ЕКСПЛУАТАЦІЇ БУРОВИХ ВЕРСТАТІВ ДЛЯ РОЗБУРЮВАННЯ ВІДБУТНИХ ВИРОБОК І СВЕРДЛОВИН

    by Юрій Маліновський, Сергій Цвіркун, Сергій Ситиник, Дмитро Власенков, Дмитро Рибак, Світлана Олійник, Yurii Malinovskyi, Sergij Tsvirkun, Serhii Sytnyk, Svitlana Oliinyk

    На сучасних гірничорудних підприємствах широко застосовують верстати обертального буріння, обладнані шарошечними бурильними головками, які використовують для проведення у твердих гірських породах свердловин 250 - 320 мм з метою виконання вибухових робіт. Буріння таких свердловин пов'язане з використанням значних осьових зусиль і обертальних моментів , які спричиняють поздовжню деформацію (стиснення) і крутильну деформацію штанг і бурового става загалом. Тому проводити інтенсифікацію процесів обертального буріння з метою збільшення діаметра свердловини, що пробурюється, пов'язано зі значними технічними труднощами й економічними витратами. У низці практичних випадків існує можливість буріння свердловин великого діаметра у два етапи. Перший етап полягає в бурінні передової свердловини малого діаметра ( 250 - 320 мм) із зовнішніх горизонтів гірничого підприємства (наприклад, шахта) до горизонту, що лежить нижче, або мережі горизонтальних виробок, з'єднаних із кар'єром. Після буріння передової свердловини ( 250 - 320 мм) на горизонт, що лежить нижче, опускається розбурювач, який одягається на буровий став замість коронки малого діаметра. Після заміни робочого інструменту діаметром 250 - 320 мм на розбурювач 1500 - 3000 мм, здійснюється розбурювання, яке ведеться вертикально вгору (іноді під кутом). При виконанні розбурювання буровий став перебуває під впливом крутного моменту і розтягувального осьового зусилля. У такому режимі роботи навантаження на став істотно зростають, проте поздовжня вісь става залишається прямолінійною, оскільки виключається вплив поздовжнього вигину, а також зменшується вплив неврівноваженості бурового става від дії початкових неправильностей та відцентрових сил. Однак істотно зростає момент сил тертя при бурінні, посилюється вплив жорсткості бурового става, з'являється можливість більш "довгих" зупинок під час роботи розбурювача в вибої, водночас зменшується величина сил пружності става зі збільшенням його довжини, а отже кут закручування збільшується. У разі збільшення кута закручування бурового става зростає динамічний крутний момент і дотичні напруження, за рахунок істотних перепадів кутової швидкості обертання става (от до 0). У даному випадку, присутні значні зміни кінетичної енергії става при зниженні кутової швидкості його обертання. Фактично зниження жорсткості става веде до зростання приросту кінетичної енергії системи на розбурювачі. Тобто динамічний кут закручування вала зростає і призводить до прояву крутильного удару з великим коефіцієнтом динамічності ( ). Як випливає з промислових випробувань верстата 2КВ 3000, не було враховано можливість прояву крутильного удару в системі розбурювач – буровий став – обертач під дією змінного моменту сил тертя між породою та інструментом. Тому за максимальної довжини става приріст кінетичної енергії удару спричиняє найбільший динамічний кут закручування става, який сприймається першими штангами від розбурювача, і в них виникають граничні наведені нормальні напруження, які призводять до поломок штанг. З цих міркувань для ефективної роботи бурових верстатів у режимі розбурювання необхідно створити та застосувати інженерну методику розрахунку динамічних параметрів бурового става і верстата загалом під впливом фрикційної взаємодії...

  • Open Access

    ТЕРМОМЕХАНІЧНІ ЯВИЩА У ПОВЕРХНЕВИХ ШАРАХ КОНТАКТУЮЧИХ ДЕТАЛЕЙ ПРИ ТЕРТІ ТА ЗНОШУВАННІ

    by Юрій Маліновський, Сергій Цвіркун, Дмитро Власенков, Світлана Олійник

    Despite a significant number of theories of friction and wear, the issue of wave formation on contacting surfaces and in the zone ahead of the moving part has not yet received a sufficiently deep justification. Based on accumulated theoretical and experimental data, it is generally accepted to consider the groups of theories: 1) geometric, 2) molecular (adhesive), 3) deformation, 4) combined [1]. The most widespread opinion is that friction is caused by plastic extrusion of the material and the destruction of welding bridges (F. R. Bowden and D. Tabor), which is also confirmed by the hypothesis of Ernst and Margent, where friction is caused by adhesion (at the molecular level and surface roughness). At the same time, the experimental results of F. R. Bowden and D. Tabor indicate that the effect of friction depends on both the adhesion forces and the deformation of the material in the thin surface layer. As a result of the application of significant compressive forces and tangential frictional forces, a large amount of energy is released at the contact of two bodies, and with weak heat exchange with the environment, high gradients of temperature changes occur, and in the case of metal parts, under certain conditions, the welding effect of both individual micro-uniformities and contact surfaces in general, which is confirmed by research results [2].


  • Open Access

    ДЕФОРМАЦІЙНИЙ АСПЕКТ ПРОЯВУ УДАРНО-ХВИЛЬОВОЇ ПРИРОДИ ТЕРТЯ ТА ЗНОШУВАННЯ

    by Юрій Маліновський, Сергій Цвіркун, Дмитро Власенков, Світлана Олійник

    As statistical analysis shows, the main reason for the failure of machines is not their destruction, but the wear of moving joints and working bodies under the influence of frictional forces. However, when creating machines, the movable joint is practically not calculated in terms of resistance to wear. At the same time, there are the following methods of tribotechnical calculation, and they are based on the following groups of theories: geometric; molecular, deformation and combined. All these theories consider processes occurring at contact surfaces. In addition, the currently used approach does not take into account the peculiarities of the deformation processes occurring in front of the mobile part. At the same time, the mobile part (stamp) «accelerates» the wave of deformation of the «launch» on the fixed part, which, as a rule, is not taken into account when considering the processes of friction and wear. We note that these deformation processes during friction and wear are due to shear deformations in front of the moving stamp, and despite established ideas, the hypothesis of flat sections is distorted, as a result of which deformation waves appear on the outer surfaces of the half-spaces. In other words, the displaced layers are not able to move freely along the shear plane, while the so-called «confined shear» occurs, which leads to the deplaning of the outer and inner planar sections. With this view of the matter, the surface layer of the half-space either loses its longitudinal stability or is subjected to cyclic stresses. In both cases, wear and intense scratching of the contact surfaces occurs. In addition, with the interaction of the die (or micro-irregularities formed on it) with the micro-irregularities of the strip in both interacting parts, a continuous wave process is established. Note that with an increase in the die speed V, the dynamic coefficient of the system changes in proportion to the change in the die speed. The research made it possible to establish that for the stable operation of the surface layers of the beam-strip it is necessary that the value of the longitudinal (critical) force overload coefficient is less than the number of half-waves of deformation formed in front of the moving die. In addition, it was established that the deformation-wave processes that occur in front of the moving die lead to the formation of permanent plastic or elastic ridges, which are obstacles for the moving die, and these obstacles are interpreted in the differential equations of motion as impulse loads. The obtained results indicate that elements of both the deformation-wave and shock-wave theories of friction and wear are manifested during the interaction of moving parts. The application of the specified approach makes it possible to clarify the calculation methods for friction and wear both in the case of deformation and in the case of geometric micro-uniformities.


  • Open Access

    ЕЛЕМЕНТИ ФРИКЦІЙНОЇ ВЗАЄМОДІЇ ТА МОЖЛИВОСТІ ЗБІЛЬШЕННЯ НАВАНТАЖЕННЯ ПАРИ КОЛЕСО – РЕЙКА

    by Юрій Маліновський, Ігор Невлюдов, Сергій Цвіркун, Дмитро Власенков, Andrij Tkachenko, Світлана Олійник

    The loading property of the wheel-rail pair is one of the main factors affecting the rational design of vehicles of various technical purposes. Based on the experience of railway transport, there is an idea that with an increase in the vertical load on the wheel and, accordingly, the rail, the durability of this pair decreases in proportion to the increase in load. However, the observations of some researchers outside of the steam load suggest that within a certain range of increasing working vertical loads on the wheel (pair of wheels) there may be a slight increase in steam strength. These data, as it were, were not refuted and did not receive theoretical confirmation. For example, from the results of solving Hertz's contact problem on the rolling of an elastic cylinder in a strip of the same material (or closed in the properties), where a direct proportion was established between the load current and New stresses in the materials of the interacting parts, and therefore proportionally reduce the durability of the pair. In contrast to the mentioned results, when setting the task, an assumption was made that the wheel and rail materials were not uniform throughout their thickness. The outer thin layers of the material under the influence of vertical and tangential adhesion loads receive surface hardening and are therefore harder, the anisotropy of the material properties of the parts in their thickness is manifested in this. In this work, an analogy was used between the task of rolling a wheel on a rail and the tasks of metal pressure processing for the cases of cold and hot rolling, running -in and other types of surface treatment of pressure parts. For these technological processes, with an increase in vertical load, significant structural changes occur in the crystal lattices of the surface layers, which can "increase", can be interpreted as a change in the modulus of elasticity and hardness indicators of the surface layers. As the depth of the stamped layer increases, the values of yield strength, strength and durability of these thin layers increase. Therefore, given this analogy, the resistance to force and wear of the corresponding pair is significantly increased during operational production within the limits limited by the so-called "critical" thickness of the stamped layer. If this thickness is exceeded, further intensive wear and further destruction of the interacting parts should follow. However, the surface strength of the parts of the wheel-rail pair can be significantly increased using static and dynamic hardening methods even before the operation of these pairs on vehicles.

  • OPTIMIZATION OF PARAMETERS OF ENERGY EFFICIENT MANAGEMENT OF THE APPLE SORTING PROCESS

    by Донецький Національний Університет Економіки І Торгівлі Імені Михайла Туган-Барановського, Л.о. Цвіркун, С.л. Цвіркун, Криворізький Національний Університет

  • RESEARCH OF TECHNICAL CHARACTERISTICS OF THE TEST KEEPING MACHINE IN THE AUTOMATED BREAD PRODUCTION LINE

    by Л.о. Цвіркун, Донецький Національний Університет Економіки І Торгівлі Імені Михайла Туган–Барановського, С.л. Цвіркун, Криворізький Національний Університет