MTMusii Tseitlin

Musii Tseitlin

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Musii Tseitlin has a total of 17 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Investigation of extraction and dehydration efficiency of granular coal slims

    by Andrii Shkop, Oleksіi Shestopalov, Natalііa Ponomarova, Musii Tseitlin, Andriі Romanchyk

    The object of research is the process of extracting the solid phase and dewatering carbon-containing products of a coal enrichment plant in the technological chain of devices “drum screen – centrifuge”. One of the most problematic areas of coal enrichment technology is the sludge waters of coal enrichment plants, which require high-quality cleaning and are promising for obtaining a fine coal fraction. This allows to reduce the load on radial thickeners, prevent coal losses and environmental pollution. During the study, an industrial experiment was used to determine the efficiency of the module, which consisted of an Ecomash DS 511A-113 drum screen and an Ecomash SHS 511A-113 centrifuge. It was established that classes larger than 1.5 mm are advisable to capture and dewater by filtering on the developed drum screen to a moisture content of 15–22 % by filtration methods. Polydisperse sludge after removal of classes larger than 1.5 mm is effectively dehydrated in a centrifuge to a residual moisture of 19.7–33 %. The degree of sludge dehydration in a centrifuge is affected by the fraction of the class content larger than 0.4 mm and the centrifuge feed capacity, which determine the formation time, compression and compactness of particle packing in the sludge. It has been established that when dewatering fine-dispersed sludge of fine classes with a particle size of less than 0.4 mm, the moisture content of the centrifuge sludge increases with increasing solid phase retention efficiency. An increase in the fraction of fine-dispersed classes in the sludge, represented mainly by wet clay, leads to an increase in moisture content to 33 % and an increase in ash content to 83–85 %. An increase in the content of granular classes 0.4–1.5 mm to 30 % and above contributes to a decrease in sludge moisture content, other things being equal, due to the squeezing of moisture from the surface of fine particles that are squeezed by larger particles. The technological chain of the module, tested in industrial conditions, consisting of a filter screen and a centrifuge, allows for the effective extraction of the granular fraction of the sludge, capturing up to 87.4 % of the solid phase, leaving only finely dispersed high-ash clay with a particle size of less than 40 microns in the centrate.


  • Open Access

    Determining heat and mass exchange kinetic in a column heat exchanger with direct phases contact

    by Musii Tseitlin, Andrii Shkop, Oleksіi Shestopalov, Valentina Raiko, Nataliia Ponomarova

    The object of this study was the processes of heat and mass transfer in a column heat exchanger with direct phases contact. The investigated problem is related to the need to determine the estimates of the kinetic characteristics of heat exchange during the concentration of solutions in a contact heat exchanger equipped with dual-flow trays. In particular, it was assumed that the determination of the influence of the gas velocity in the apparatus and the density of liquid irrigation of the plates, as well as the geometry of the plates, on the kinetic coefficients would make it possible to reveal the patterns of heat and mass exchange between the liquid and the air in contact with it in the column apparatus. It was determined that to increase the intensity of mass transfer in the gas and heat transfer in the liquid, it is necessary to increase the gas velocity and irrigation density. Then the gas velocity and irrigation density have approximately the same effect on the intensity of mass transfer in the gas and heat transfer in the liquid. When studying the effect of the geometry of the plate on the kinetic coefficients of heat transfer in the liquid and mass transfer in the gas, it was established that the value of the portion of the free cross section of the plate has a decisive influence on the value of the considered kinetic coefficients. A generalized equation was built, which makes it possible not only to calculate the enthalpy transfer coefficient during the interaction of sodium chloride solution with air but also to determine the limiting stage of this process. The results could be used to design a unit for concentrating a hot solution of sodium chloride by evaporating water during blowing with air in a contact heat exchanger. This would make it possible to obtain crystalline sodium chloride using secondary energy resources and other non-traditional sources of thermal energy

  • Comparative Evaluation of the Contact Elements Efficiency for Barium Sulfide Solution Carbonization

    by Yurij Masikevych, Musii Tseitlin, Valentyna Raiko, Oleksii Shestopalov, Vladimir Panasenko

  • Open Access

    Defining features in the kinetics of sodium carbonate-bicarbonate solution carbonization and the quality of the resulting sodium bicarbonate crystals

    by Mykola Porokhnia, Musii Tseitlin, Svitlana Bukhkalo, Vladimir Panasenko, Tetiana Novozhylova

    This paper reports a study into the influence of temperature and gas consumption on the carbonization kinetics (saturation with carbon dioxide) of sodium carbonate-bicarbonate solution. The study also examined the quality and speed of crystal formation in this process. This research is predetermined by the environmental problems faced by modern enterprises that produce purified sodium bicarbonate – an insufficient degree of carbonization and, as a result, excessive air pollution with carbon dioxide, which did not participate in the reaction during the process. This study addresses these particular issues. As a result of using specialized laboratory equipment, it was found that an increase in the absorbent temperature from 79 to 85 °C leads to a decrease in the maximum degree of carbonization of the solution from 64 to 59 %. In contrast, the quality of the resulting sodium bicarbonate crystals improves but only in the range from 79 to 82 °C. With a further increase in temperature, the quality stabilizes. It is shown that the carbonization rate increases with increasing specific consumption of the absorbent (carbon dioxide) and is characterized by a negative correlation with the value of oversaturation of the absorbent in terms of NaНCO3. The quality of sodium bicarbonate crystals decreases with increasing gas velocity. Thus, it was reasonable to assume that the established dependence of the kinetics of carbonization of Na2CO3 and NaНCO3 solution on the gas velocity in the apparatus is explained by the inhibition of СО2 absorption, which is caused by the diffusion resistance of sodium bicarbonate crystallization. To improve the quality of crystals and the productivity of carbonization by reducing the supersaturation in terms of NaНCO3, it is recommended to introduce a seed crystal in the zone of binding of crystals in the carbonization columns.


  • Open Access

    OPTIMIZATION OF FLOCCULAR CLEANING AND DRAINAGE OF THIN DISPERSED SLUDGES

    by Oleksii Shestopalov, Oleksandr Briankin, Nadegda Rykusova, Oksana Hetta, Valentina Raiko, Musii Tseitlin

    The efficiency of solid phase retention and dehydration of finely dispersed products of a coal processing plant and a metallurgical enterprise on the module for cleaning and dewatering sludge is investigated. A technique for selecting the operating parameters of equipment based on the determination of the strength criterion of flocs is proposed. A methodology for technological tests has been developed to control the flocculation process and optimize the flow of flocculant depending on the concentration of the solid phase. Industrial tests on the module for wastewater treatment and sludge dewatering using flocculants proved the effectiveness of the developed methodology. It is shown that the conditions for conducting tests on flocculation should correspond to the operating conditions of the circuit apparatus for cleaning and dewatering sludge. These conditions include sludge performance, sludge flow rate in the cross section of pipes and apparatuses, and the flow time from the flocculator to the centrifuge. During the testing of the Module, the solids retention efficiency of 97–99 % was achieved with the strength criteria of flocs in front of a centrifuge of 2–2.5 mm/s. The conditions for the high efficiency of the apparatus chain are the optimization of the aggregation process itself. It is revealed that for the formation of strong flocs it is necessary to regulate the concentration of the solid phase. For coal sludge, the concentration of the solid phase before the flocculant is fed must be maintained no higher than 50–60 g/l, and for gas treatment sludge – no higher than 20–25 g/l. Correction of the concentration of sludge before the flocculator is possible by diluting it with clarified water to the optimum concentration for aggregation. It is found that the moisture content of the sediment and the efficiency of the retention of the solid phase depend on the strength criterion of the flocs. Therefore, the optimization of the flocculant flow rate is possible by controlling and the residual floccule deposition rate after mechanical action in front of the dewatering equipment. The flocculant flow rate must be adjusted depending on the concentration of the solid phase in the sludge to achieve the desired criterion for the strength of the flocs


  • Open Access

    Studying patterns in the flocculation of sludges from wet gas treatment in metallurgical production

    by Oleksii Shestopalov, Oleksandr Briankin, Musii Tseitlin, Valentina Raiko, Oksana Hetta

    Studying patterns in the flocculation of sludges from wet gas treatment in metallurgical production