Nataša Kopitović Vuković
Research Subjects
Nataša Kopitović Vuković has a total of 6 co-authors. Here are the top co-authors by number of shared publications:
- Nikola Baša
Univerzitet Crne Gore
2 shared publications M. Jevrić
University of Montenegro, Faculty of Civil Engineering, Podgorica, Montenegro
1 shared publication- Mladen Muhadinović
Univ Montenegro, Civil Engn Fac Podgor, Podgorica, Montenegro
1 shared publication - Mladen Ulićević
Faculty of Civil Engineering, University of Montenegro, Cetinjski put bb, 81000 Podgorica, Montenegro
1 shared publication Nataša Kopitović Vuković
University of Montenegro,Podgorica,Montenegro
1 shared publicationR. Zejak
University of Montenegro, Faculty of Civil Engineering, Podgorica, Montenegro
1 shared publication
Latest Publications
- Open Access
- 30 April 2025
- Published by Faculty of Civil Engineering and Architecture, University of Nis in Nauka+Praksa
- Vol. 28 (1) , 1-9
NUMERIČKA ANALIZA PONAŠANJA GREDA T-PRESJEKA OJAČANIH KARBONSKIM TRAKAMA
Ovaj rad proučava efikasnost spoljašnjeg sistema ojačanja prostih greda, kroz numeričku analizu sprovedenu pomoću softvera ANSYS. Ojačanje je izvedeno u vidu traka postavljenih na rebro T-presjeka. Primijenjene su različite šeme ojačanja i vrste opterećenja, kako bi se utvrdio uticaj ovih parametara na ukupno ponašanje uzoraka za ispitivanje. Odgovor ovakvog sistema ojačanja analiziran je kroz njegovo naponsko-deformacijsko stanje, te kroz poređenje s neojačanim kontrolnim uzorcima.U cilju verifikacije dobijenih rezultata, sprovedeno je eksperimentalno istraživanje na prostim AB gredama u punoj veličini, koje su bile u eksploataciji više od 10 godina. Utvrđeno je zadovoljavajuće slaganje sa numerički dobijenim vrijednostima, budući da je u računarskom modeliranju neophodno uvoditi određena pojednostavljenja, pa su i razlike u vrijednostima karakteristika kojima se opisuje naponsko-deformacijsko stanje posmatranog elementa očekivane.
- 30 April 2025
- Published by Faculty of Civil Engineering and Architecture, University of Nis in Nauka+Praksa
- Vol. 28 (1) , 1-9
Open AccessNUMERIČKA ANALIZA PONAŠANJA GREDA T-PRESJEKA OJAČANIH KARBONSKIM TRAKAMA
Ovaj rad proučava efikasnost spoljašnjeg sistema ojačanja prostih greda, kroz numeričku analizu sprovedenu pomoću softvera ANSYS. Ojačanje je izvedeno u vidu traka postavljenih na rebro T-presjeka. Primijenjene su različite šeme ojačanja i vrste opterećenja, kako bi se utvrdio uticaj ovih parametara na ukupno ponašanje uzoraka za ispitivanje. Odgovor ovakvog sistema ojačanja analiziran je kroz njegovo naponsko-deformacijsko stanje, te kroz poređenje s neojačanim kontrolnim uzorcima.U cilju verifikacije dobijenih rezultata, sprovedeno je eksperimentalno istraživanje na prostim AB gredama u punoj veličini, koje su bile u eksploataciji više od 10 godina. Utvrđeno je zadovoljavajuće slaganje sa numerički dobijenim vrijednostima, budući da je u računarskom modeliranju neophodno uvoditi određena pojednostavljenja, pa su i razlike u vrijednostima karakteristika kojima se opisuje naponsko-deformacijsko stanje posmatranog elementa očekivane.
- Open Access
- 8 June 2020
- Published by MDPI AG in Applied Sciences
- Vol. 10 (11) , 3973
Effects of Internal Force Redistribution on the Limit States of Continuous Beams with GFRP Reinforcement
Fiber-reinforced polymers (FRP) are commonly used as internal reinforcement in RC structures in aggressive environments. The design of concrete elements reinforced with FRP bars is usually ruled by serviceability criteria rather than the ultimate limit state. Six continuous concrete beams over two spans with longitudinal and transverse glass FRP (GFRP) reinforcement were investigated until failure to estimate the effects of different reinforcement arrangements on the limit states of continuous beams. The ratio of longitudinal reinforcement between the midspan and middle support sections (i.e., the design moment redistribution) and the type of GFRP reinforcement were the main parameters. The experimental results were compared to prediction models and other code formulations under serviceability and ultimate limit states. The bond-dependent coefficient kb was investigated to assess adhesion conditions for GFRP reinforcement and concrete. The results showed that moment redistribution in continuous beams with GFRP reinforcement happens with slippage between the reinforcement and concrete in the middle support without the load capacity being reduced. A modified model was suggested for better deflection prediction of continuous beams reinforced with GFRP bars. Based on deformability factors, the tested continuous beams, although containing GFRP reinforcement that has brittle behavior, showed a certain kind of ductile behavior.
- 8 June 2020
- Published by MDPI AG in Applied Sciences
- Vol. 10 (11) , 3973
Open AccessEffects of Internal Force Redistribution on the Limit States of Continuous Beams with GFRP Reinforcement
Fiber-reinforced polymers (FRP) are commonly used as internal reinforcement in RC structures in aggressive environments. The design of concrete elements reinforced with FRP bars is usually ruled by serviceability criteria rather than the ultimate limit state. Six continuous concrete beams over two spans with longitudinal and transverse glass FRP (GFRP) reinforcement were investigated until failure to estimate the effects of different reinforcement arrangements on the limit states of continuous beams. The ratio of longitudinal reinforcement between the midspan and middle support sections (i.e., the design moment redistribution) and the type of GFRP reinforcement were the main parameters. The experimental results were compared to prediction models and other code formulations under serviceability and ultimate limit states. The bond-dependent coefficient kb was investigated to assess adhesion conditions for GFRP reinforcement and concrete. The results showed that moment redistribution in continuous beams with GFRP reinforcement happens with slippage between the reinforcement and concrete in the middle support without the load capacity being reduced. A modified model was suggested for better deflection prediction of continuous beams reinforced with GFRP bars. Based on deformability factors, the tested continuous beams, although containing GFRP reinforcement that has brittle behavior, showed a certain kind of ductile behavior.
- 9 March 2020
- Published by Springer Nature in Mechanics of Composite Materials
- Vol. 56 (1) , 75-84
Experimental Analysis of RC Elements Strengthened with CFRP Strips
- 9 March 2020
- Published by Springer Nature in Mechanics of Composite Materials
- Vol. 56 (1) , 75-84
Experimental Analysis of RC Elements Strengthened with CFRP Strips