Jan Suchý
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Jan Suchý has a total of 22 co-authors. Here are the top co-authors by number of shared publications:
- Jiří Kubásek
Department of Metals and Corrosion Engineering, University of Chemistry and Technology, Technická 5, 166 28 Prague, Czech Republic
4 shared publications Dalibor Vojtěch
3 shared publications- Daniel Koutný
Faculty of Mechanical Engineering Brno University of Technology Technicka 2 61669 Brno Czech Republic
3 shared publications David Paloušek
3 shared publications- Michaela Roudnická
University of Chemistry and Technology Prague
2 shared publications Patrícia Krištofová
2 shared publications
Latest Publications
- Open Access
Biodegradable WE43 Magnesium Alloy Produced by Selective Laser Melting: Mechanical Properties, Corrosion Behavior, and In-Vitro Cytotoxicity
In this work, selective laser melting (SLM) technology was used to prepare Mg-4Y-3Nd-Zr (WE43) alloy. This alloy and production method are promising for the design of biodegradable implants. The aim of this study was to investigate the chemical composition, microstructure, mechanical properties, corrosion behavior in simulated body fluid (SBF), and cytotoxicity of the alloy produced by SLM method and to compare it with conventionally gravity cast reference alloy. Analysis of the surface of the revealed an oxygen content of 7 wt.%. Undesirable unmelted and only partially adhered spherical particles of the starting powder were also found. The microstructure of the material was very fine and consisted of α-Mg dendritic matrix, β-Mg41(Nd, Y)5 intermetallic phase, Y2O3 inclusions, and 0.6 vol.% of residual porosity. The Vickers hardness, compressive yield strength, compressive strength, and maximum compressive strain were 88 HV0.1, 201 MPa, 394 MPa, and 14%, respectively, which are close to the reference values in as-cast. The in vitro corrosion rates determined by immersion and potentiodynamic tests were 2.6 mm/year and 1.3 mm/year, respectively. Cytotoxicity tests indicated good biocompatibility of the 3D-printed alloy.
Open AccessBiodegradable WE43 Magnesium Alloy Produced by Selective Laser Melting: Mechanical Properties, Corrosion Behavior, and In-Vitro Cytotoxicity
In this work, selective laser melting (SLM) technology was used to prepare Mg-4Y-3Nd-Zr (WE43) alloy. This alloy and production method are promising for the design of biodegradable implants. The aim of this study was to investigate the chemical composition, microstructure, mechanical properties, corrosion behavior in simulated body fluid (SBF), and cytotoxicity of the alloy produced by SLM method and to compare it with conventionally gravity cast reference alloy. Analysis of the surface of the revealed an oxygen content of 7 wt.%. Undesirable unmelted and only partially adhered spherical particles of the starting powder were also found. The microstructure of the material was very fine and consisted of α-Mg dendritic matrix, β-Mg41(Nd, Y)5 intermetallic phase, Y2O3 inclusions, and 0.6 vol.% of residual porosity. The Vickers hardness, compressive yield strength, compressive strength, and maximum compressive strain were 88 HV0.1, 201 MPa, 394 MPa, and 14%, respectively, which are close to the reference values in as-cast. The in vitro corrosion rates determined by immersion and potentiodynamic tests were 2.6 mm/year and 1.3 mm/year, respectively. Cytotoxicity tests indicated good biocompatibility of the 3D-printed alloy.
- Open Access
Effect of Laser Parameters on Processing of Biodegradable Magnesium Alloy WE43 via Selective Laser Melting Method
The global aim of the theme of magnesium alloy processing by the selective laser melting technology is to enable printing of replacements into the human body. By combining the advantages of WE43 magnesium alloy and additive manufacturing, it is possible to print support structures that have very similar properties to human bones. However, printing magnesium alloy parts is very difficult, and the printing strategies are still under development. Knowledge of weld deposit behaviour is needed to design a complex printing strategy and still missing. The main aim of the manuscript is the find a stable process window and identify the dependence of the weld deposit shape and properties on the laser power and scanning speed. The range of the tested parameters was 100–400 W and 100–800 mm/s for laser power and scanning speed. The profilometry and light microscopy were used to verify the continuity and shape evaluation. The microhardness and EDX analysis were used for the detailed view of the weld deposit. The manuscript specifies the weld deposit dimensions, their changes depending on laser power and scanning speed, and the continuity of the weld tracks. The stable weld deposits are made by the energy density of 5.5–12 J/mm2. Thin walls were also created by layering welds to determine the surface roughness scattering (Ra 35–60) for various settings of laser power and scanning speed.
Open AccessEffect of Laser Parameters on Processing of Biodegradable Magnesium Alloy WE43 via Selective Laser Melting Method
The global aim of the theme of magnesium alloy processing by the selective laser melting technology is to enable printing of replacements into the human body. By combining the advantages of WE43 magnesium alloy and additive manufacturing, it is possible to print support structures that have very similar properties to human bones. However, printing magnesium alloy parts is very difficult, and the printing strategies are still under development. Knowledge of weld deposit behaviour is needed to design a complex printing strategy and still missing. The main aim of the manuscript is the find a stable process window and identify the dependence of the weld deposit shape and properties on the laser power and scanning speed. The range of the tested parameters was 100–400 W and 100–800 mm/s for laser power and scanning speed. The profilometry and light microscopy were used to verify the continuity and shape evaluation. The microhardness and EDX analysis were used for the detailed view of the weld deposit. The manuscript specifies the weld deposit dimensions, their changes depending on laser power and scanning speed, and the continuity of the weld tracks. The stable weld deposits are made by the energy density of 5.5–12 J/mm2. Thin walls were also created by layering welds to determine the surface roughness scattering (Ra 35–60) for various settings of laser power and scanning speed.
- 26 May 2020
- Published by SAGE Publications in Powder Metallurgy
- Vol. 63 (3) , 197-211
Processing of AlSi9Cu3 alloy by selective laser melting
Additive manufacturing of Al-alloys allows the production of components with a complicated structured shape, geometry composed by lattice structures, internal cooling, etc. The portfolio of Al-alloys for metal additive manufacturing is still under development and is strongly limited, compared to the conventional technology. The alloy AlSi9Cu3 is used in many applications, but its processing details are still missing. The main aim of this paper is to describe the laser process parameters for AlSi9Cu3, processed by SLM technology and manufactured from two powders of different shapes and particle sizes. The tested process parameters were laser power, laser speed, and hatch distance in the range of 100–400 W, 200–1500 mm · s−1 and 90–150 µm. These were tested using a single-track and cube test. Microstructure, mechanical properties and the fatigue of SLM samples were analysed and compared with as-casted material.
- 26 May 2020
- Published by SAGE Publications in Powder Metallurgy
- Vol. 63 (3) , 197-211
Processing of AlSi9Cu3 alloy by selective laser melting
Additive manufacturing of Al-alloys allows the production of components with a complicated structured shape, geometry composed by lattice structures, internal cooling, etc. The portfolio of Al-alloys for metal additive manufacturing is still under development and is strongly limited, compared to the conventional technology. The alloy AlSi9Cu3 is used in many applications, but its processing details are still missing. The main aim of this paper is to describe the laser process parameters for AlSi9Cu3, processed by SLM technology and manufactured from two powders of different shapes and particle sizes. The tested process parameters were laser power, laser speed, and hatch distance in the range of 100–400 W, 200–1500 mm · s−1 and 90–150 µm. These were tested using a single-track and cube test. Microstructure, mechanical properties and the fatigue of SLM samples were analysed and compared with as-casted material.
- Open Access
- 1 August 2019
- Published by Jan Evangelista Purkyne University in Usti nad Labem in Manufacturing Technology
- Vol. 19 (4) , 613-618
Influence of Production Parameters on the Properties of 3D Printed Magnesium Alloy Mg-4Y-3RE-Zr (WE43)
Detail záznamu - Influence of production parameters on the properties of 3D printed magnesium alloy Mg-4Y-3RE-Zr (WE43) - Detailní zobrazení záznamu - Vědecká knihovna UJEP
- 1 August 2019
- Published by Jan Evangelista Purkyne University in Usti nad Labem in Manufacturing Technology
- Vol. 19 (4) , 613-618
Open AccessInfluence of Production Parameters on the Properties of 3D Printed Magnesium Alloy Mg-4Y-3RE-Zr (WE43)
Detail záznamu - Influence of production parameters on the properties of 3D printed magnesium alloy Mg-4Y-3RE-Zr (WE43) - Detailní zobrazení záznamu - Vědecká knihovna UJEP
- Open Access
- 1 February 2019
- Published by Jan Evangelista Purkyne University in Usti nad Labem in Manufacturing Technology
- Vol. 19 (1) , 89-94
Microstructure of the Mg-4Y-3RE-Zr (WE43) Magnesium Alloy Produced by 3D Printing
Detail záznamu - Microstructure of the Mg-4Y-3RE-Zr (WE43) magnesium alloy produced by 3D printing - Detail záznamu - Vědecká knihovna UJEP
- 1 February 2019
- Published by Jan Evangelista Purkyne University in Usti nad Labem in Manufacturing Technology
- Vol. 19 (1) , 89-94
Open AccessMicrostructure of the Mg-4Y-3RE-Zr (WE43) Magnesium Alloy Produced by 3D Printing
Detail záznamu - Microstructure of the Mg-4Y-3RE-Zr (WE43) magnesium alloy produced by 3D printing - Detail záznamu - Vědecká knihovna UJEP
- 1 January 2019
- Published by TANGER Ltd.
structure and properties of additively manufactured WE43 magnesium alloy
- 1 January 2019
- Published by TANGER Ltd.
structure and properties of additively manufactured WE43 magnesium alloy