Shuiping Zhong
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Shuiping Zhong has a total of 65 co-authors. Here are the top co-authors by number of shared publications:
- Wei Weng
Zijin School of Geology and Mining, Fuzhou University, Fuzhou, China
9 shared publications Xiaopeng Chi
Zijin School of Geology and Mining, Fuzhou University, Fuzhou, China
6 shared publicationsHang Chen
Zijin Mining Group Co., Ltd., Longyan, China
4 shared publications- Ding Tang
Zijin Mining Group Co., Ltd., Shanghang, Longyan 364200, China
3 shared publications Haoyu Liu
Zijin College of Geology and Mining, Fuzhou University, Fuzhou, China
3 shared publicationsJun Xia
College of Materials Science and Engineering, Fuzhou University, Fuzhou, China
3 shared publications
Latest Publications
- Open Access
Gold Recovery Beyond Ores: Sources, Processes, Challenges, and Prospects
Gold (Au) is a strategically critical metal whose technological relevance and increasing demand contrast with the long-term decline in primary ore grades. This review discusses gold recovery from primary ores providing the metallurgical and technological baseline for the comparative evaluation of unconventional Au-bearing resources. Emphasis is placed on electronic waste and copper anode slimes as highly valuable secondary raw materials containing gold concentrations comparable to, or exceeding, those in natural deposits. The review examines the origin, chemical and mineralogical characteristics, impurity profiles, and processing routes associated with these materials, including conventional and emerging pyro-, hydro-, and biometallurgical approaches. Material-specific constraints, matrix complexity, recovery efficiency, process limitations, and environmental aspects are discussed in relation to process applicability and technological feasibility. Particular attention is given to the differences between geologically constrained primary ores and heterogeneous secondary Au-bearing materials, whose engineered and continuously evolving compositions influence recovery strategies, limiting the direct application of conventional routes to secondary resources. Finally, the review highlights that primary ores remain the dominant source of global Au production, whereas secondary resources currently represent a complementary component, and outlines key challenges and future directions relevant to the broader utilization of these materials.
Open AccessGold Recovery Beyond Ores: Sources, Processes, Challenges, and Prospects
Gold (Au) is a strategically critical metal whose technological relevance and increasing demand contrast with the long-term decline in primary ore grades. This review discusses gold recovery from primary ores providing the metallurgical and technological baseline for the comparative evaluation of unconventional Au-bearing resources. Emphasis is placed on electronic waste and copper anode slimes as highly valuable secondary raw materials containing gold concentrations comparable to, or exceeding, those in natural deposits. The review examines the origin, chemical and mineralogical characteristics, impurity profiles, and processing routes associated with these materials, including conventional and emerging pyro-, hydro-, and biometallurgical approaches. Material-specific constraints, matrix complexity, recovery efficiency, process limitations, and environmental aspects are discussed in relation to process applicability and technological feasibility. Particular attention is given to the differences between geologically constrained primary ores and heterogeneous secondary Au-bearing materials, whose engineered and continuously evolving compositions influence recovery strategies, limiting the direct application of conventional routes to secondary resources. Finally, the review highlights that primary ores remain the dominant source of global Au production, whereas secondary resources currently represent a complementary component, and outlines key challenges and future directions relevant to the broader utilization of these materials.
- 6 May 2025
- Published by Springer Nature in Journal of Materials Science
- Vol. 60 (18) , 7641-7652
Study on the influence of copper foil current collector roughness on lithium-ion battery performance
- 6 May 2025
- Published by Springer Nature in Journal of Materials Science
- Vol. 60 (18) , 7641-7652
Study on the influence of copper foil current collector roughness on lithium-ion battery performance
- 30 August 2024
- Published by Springer Nature in International Journal of Minerals, Metallurgy and Materials
- Vol. 31 (10) , 2312-2325
Breaking the Fe3O4-wrapped copper microstructure to enhance copper–slag separation
- 30 August 2024
- Published by Springer Nature in International Journal of Minerals, Metallurgy and Materials
- Vol. 31 (10) , 2312-2325
Breaking the Fe3O4-wrapped copper microstructure to enhance copper–slag separation
- 11 July 2024
- Published by Springer Nature in JOM
- Vol. 76 (9) , 4837-4848
Density Tuning in Conjunction with Pelletizing of Reductants for Enhanced Recovery from Copper Smelting Slag
- 11 July 2024
- Published by Springer Nature in JOM
- Vol. 76 (9) , 4837-4848
Density Tuning in Conjunction with Pelletizing of Reductants for Enhanced Recovery from Copper Smelting Slag
- 1 December 2023
- Published by The Electrochemical Society in Journal of the Electrochemical Society
- Vol. 170 (12) , 127505
Size-Optimized Silver Nanowires with Graphene Oxide for High-Performance Transparent Electrodes
Silver nanowires (AgNWs)-based transparent electrode is one critical component for many modern electronic devices, however, preparation of high-performance AgNWs-based transparent electrode with appealing light transmittance and long-term stability is still challenging. Herein, by combining the size-optimized AgNWs with graphene oxide (GO), the composite AgNWs/GO film electrode with high light-transmittance and appealing stability is prepared. For the size-controlled preparation of AgNWs, well-defined one-dimensional structure (average diameter = 62 nm) is obtained by elaborately adjusting the Br− concentration (0.05 mM), Cl− concentration (1 mM), ratio of PVP/AgNO3 (5:1) and PVP-type selection (PVP1300k: PVP58k = 2:1), contributing to a high light transmittance of 84% for the corresponding AgNWs-based electrode. After further introducing the GO, the film electrode presents much enhanced stability and increased film-substrate adhesive strength, namely only 3.6% increase in resistance after 1000 cycles of bending and being stable even under ultrasonic vibration. The results can provide new insights for designing electrode with ultrastability and high light transmittance.
- 1 December 2023
- Published by The Electrochemical Society in Journal of the Electrochemical Society
- Vol. 170 (12) , 127505
Size-Optimized Silver Nanowires with Graphene Oxide for High-Performance Transparent Electrodes
Silver nanowires (AgNWs)-based transparent electrode is one critical component for many modern electronic devices, however, preparation of high-performance AgNWs-based transparent electrode with appealing light transmittance and long-term stability is still challenging. Herein, by combining the size-optimized AgNWs with graphene oxide (GO), the composite AgNWs/GO film electrode with high light-transmittance and appealing stability is prepared. For the size-controlled preparation of AgNWs, well-defined one-dimensional structure (average diameter = 62 nm) is obtained by elaborately adjusting the Br− concentration (0.05 mM), Cl− concentration (1 mM), ratio of PVP/AgNO3 (5:1) and PVP-type selection (PVP1300k: PVP58k = 2:1), contributing to a high light transmittance of 84% for the corresponding AgNWs-based electrode. After further introducing the GO, the film electrode presents much enhanced stability and increased film-substrate adhesive strength, namely only 3.6% increase in resistance after 1000 cycles of bending and being stable even under ultrasonic vibration. The results can provide new insights for designing electrode with ultrastability and high light transmittance.
- 1 November 2023
- Published by The Electrochemical Society in Journal of the Electrochemical Society
- Vol. 170 (11) , 112504
Incorporating an Efficient Oxygen Evolution Catalyst of MnCo 2 O 4.5 into a Pb Matrix as an Energy-Saving Anode for Metal Electrowinning
Based on the outstanding catalytic activity and stability of Mn-Co bimetallic oxides toward oxygen evolution in acidic solutions, MnCo 2 O 4.5 was incorporated into a Pb matrix through a powder pressing-sintering process to obtain a Pb-MnCo 2 O 4.5 composite anode. The results show that compared with the Pb anode that was made via the powder pressing-sintering process (PS-Pb), the oxide layer formed on the Pb-MnCo 2 O 4.5 anode presented a higher flatness, compactness, and β -PbO 2 concentration. Consequently, Pb-5.0MnCo 2 O 4.5 presented a stable anodic potential of 1.235 V, approximately 170 mV lower than that of the PS-Pb anode. In the case of lower MnCo 2 O 4.5 content (≤2.5%), the Pb-MnCo 2 O 4.5 composite anode exhibited a smaller Tafel slope (70.39 ∼ 79.59 mV dec −1 ) and a lower charge transfer resistance (0.437 ∼ 0.676 Ω cm 2 ). The fresh Pb-5.0MnCo 2 O 4.5 composite anode showed a self-corrosion density of 0.25 mA cm −2 , approximately 14.3% of that tested on the PS-Pb anode. However, Co 2+ and Mn 2+ were detected in the electrolyte during 72 h of electrowinning with the Pb-MnCo 2 O 4.5 composite anode. In summary, the Pb-MnCo 2 O 4.5 composite anode has the potential to reduce the energy consumption of the metal-electrowinning process. Nonetheless, it is necessary to evaluate the influence of dissolved Co 2+ and Mn 2+ on the cathodic process before commercial application.
- 1 November 2023
- Published by The Electrochemical Society in Journal of the Electrochemical Society
- Vol. 170 (11) , 112504
Incorporating an Efficient Oxygen Evolution Catalyst of MnCo 2 O 4.5 into a Pb Matrix as an Energy-Saving Anode for Metal Electrowinning
Based on the outstanding catalytic activity and stability of Mn-Co bimetallic oxides toward oxygen evolution in acidic solutions, MnCo 2 O 4.5 was incorporated into a Pb matrix through a powder pressing-sintering process to obtain a Pb-MnCo 2 O 4.5 composite anode. The results show that compared with the Pb anode that was made via the powder pressing-sintering process (PS-Pb), the oxide layer formed on the Pb-MnCo 2 O 4.5 anode presented a higher flatness, compactness, and β -PbO 2 concentration. Consequently, Pb-5.0MnCo 2 O 4.5 presented a stable anodic potential of 1.235 V, approximately 170 mV lower than that of the PS-Pb anode. In the case of lower MnCo 2 O 4.5 content (≤2.5%), the Pb-MnCo 2 O 4.5 composite anode exhibited a smaller Tafel slope (70.39 ∼ 79.59 mV dec −1 ) and a lower charge transfer resistance (0.437 ∼ 0.676 Ω cm 2 ). The fresh Pb-5.0MnCo 2 O 4.5 composite anode showed a self-corrosion density of 0.25 mA cm −2 , approximately 14.3% of that tested on the PS-Pb anode. However, Co 2+ and Mn 2+ were detected in the electrolyte during 72 h of electrowinning with the Pb-MnCo 2 O 4.5 composite anode. In summary, the Pb-MnCo 2 O 4.5 composite anode has the potential to reduce the energy consumption of the metal-electrowinning process. Nonetheless, it is necessary to evaluate the influence of dissolved Co 2+ and Mn 2+ on the cathodic process before commercial application.
- Open Access
- 1 September 2023
- Published by The Electrochemical Society in Journal of the Electrochemical Society
- Vol. 170 (9) , 097506
Extending Silver Nanowire Modified Electrodes to Industrial Zinc Electrolyte for Copper Ion Detection
Real-time and rapid determination of trace copper ion (Cu2+) in the electrolyte of zinc smelting process is urgently needed. However, the complicated composition of the electrolyte, especially the extremely high-concentration of zinc ion (Zn2+) may cause severe interference to the detection of Cu2+. This work describes a facile electrochemical sensor for Cu2+ determination in the electrolyte of zinc smelting plants based on a fluorine-doped tin oxide (FTO) electrode with silver nanowires (AgNWs) and Nafion modification. The AgNWs/Nafion-FTO electrode showed good detection ability with the linear detection range of 0.2−2 mg l−1 Cu2+ in 45 g l−1 Zn2+ solution using differential pulse anodic stripping voltammetry (DPASV) technique. With DPASV technique, Cu2+ can be first reduced and pre-concentrated on the working electrode surface at −0.6 V vs Ag/AgCl for 500 s, after which the deposited Cu metal is oxidized around 0 V vs Ag/AgCl during the stripping step. It has been proved by transmission electron microscopy (TEM) and X-ray photoelectron spectra (XPS) that trace Cu2+ can be adsorbed and reduced on AgNWs in solutions with Zn/Cu ratio up to (2.25−22.5) × 104. The results extend AgNWs modified electrode to the industrial solution, providing a new strategy for detection of trace metal ions in industrial solutions.
- 1 September 2023
- Published by The Electrochemical Society in Journal of the Electrochemical Society
- Vol. 170 (9) , 097506
Open AccessExtending Silver Nanowire Modified Electrodes to Industrial Zinc Electrolyte for Copper Ion Detection
Real-time and rapid determination of trace copper ion (Cu2+) in the electrolyte of zinc smelting process is urgently needed. However, the complicated composition of the electrolyte, especially the extremely high-concentration of zinc ion (Zn2+) may cause severe interference to the detection of Cu2+. This work describes a facile electrochemical sensor for Cu2+ determination in the electrolyte of zinc smelting plants based on a fluorine-doped tin oxide (FTO) electrode with silver nanowires (AgNWs) and Nafion modification. The AgNWs/Nafion-FTO electrode showed good detection ability with the linear detection range of 0.2−2 mg l−1 Cu2+ in 45 g l−1 Zn2+ solution using differential pulse anodic stripping voltammetry (DPASV) technique. With DPASV technique, Cu2+ can be first reduced and pre-concentrated on the working electrode surface at −0.6 V vs Ag/AgCl for 500 s, after which the deposited Cu metal is oxidized around 0 V vs Ag/AgCl during the stripping step. It has been proved by transmission electron microscopy (TEM) and X-ray photoelectron spectra (XPS) that trace Cu2+ can be adsorbed and reduced on AgNWs in solutions with Zn/Cu ratio up to (2.25−22.5) × 104. The results extend AgNWs modified electrode to the industrial solution, providing a new strategy for detection of trace metal ions in industrial solutions.