Chunyang Xia
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Chunyang Xia has a total of 30 co-authors. Here are the top co-authors by number of shared publications:
- Huijun Li
University of Wollongong
8 shared publications Zengxi Pan
University of Wollongong
6 shared publicationsJoseph Polden
School of Mechanical, Materials, Mechatronic and Biomedical Engineering, University of Wollongong, Wollongong, Australia
5 shared publicationsShanben Chen
School of Materials Science and Engineering, Shanghai Jiao Tong University, Shanghai, China
4 shared publicationsYuxing Li
University of Wollongong
4 shared publications- Zengxi Pan
University of Wollongong
4 shared publications
Latest Publications
- Open Access
- 17 September 2025
- Published by Taylor & Francis in Virtual and Physical Prototyping
- Vol. 20 (1)
Surrogate modelling of thermal and residual stress fields in cold-spray additive manufacturing using machine learning
- 17 September 2025
- Published by Taylor & Francis in Virtual and Physical Prototyping
- Vol. 20 (1)
Open AccessSurrogate modelling of thermal and residual stress fields in cold-spray additive manufacturing using machine learning
- 10 December 2022
- Published by Springer Nature
- p. 33-43
Machine Learning in Process Monitoring and Control for Wire-Arc Additive Manufacturing
- 10 December 2022
- Published by Springer Nature
- p. 33-43
Machine Learning in Process Monitoring and Control for Wire-Arc Additive Manufacturing
- Open Access
- 28 March 2022
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 120 (7-8) , 5225-5242
Towards intelligent monitoring system in wire arc additive manufacturing: a surface anomaly detector on a small dataset
Rapid developments in artificial intelligence and image processing have presented many new opportunities for defect detection in manufacturing processes. In this work, an intelligent image processing system has been developed to monitor inter-layer deposition quality during a wire arc additive manufacturing (WAAM) process. This system reveals the feasibility and future potential of using computer vision knowledge in WAAM. Information produced from this system is to be used in conjunction with other quality monitoring systems to verify the quality of fabricated components. It is tailored to identify the presence of defects relating to lack of fusion and voids immediately after the deposition of a given layer. The image processing system is built upon the YOLOv3 architecture and through moderate changes on anchor settings and achieves 53% precision on surface anomaly detection and 100% accuracy in identifying the fabricated components’ location, providing a prerequisite for high-precision assessment of welding quality. The work presented in this paper presents an inter-layer vision-based defect monitoring system in WAAM and serves to highlight the feasibility of developing such intelligent computer vision systems for monitoring the WAAM process for defects.
- 28 March 2022
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 120 (7-8) , 5225-5242
Open AccessTowards intelligent monitoring system in wire arc additive manufacturing: a surface anomaly detector on a small dataset
Rapid developments in artificial intelligence and image processing have presented many new opportunities for defect detection in manufacturing processes. In this work, an intelligent image processing system has been developed to monitor inter-layer deposition quality during a wire arc additive manufacturing (WAAM) process. This system reveals the feasibility and future potential of using computer vision knowledge in WAAM. Information produced from this system is to be used in conjunction with other quality monitoring systems to verify the quality of fabricated components. It is tailored to identify the presence of defects relating to lack of fusion and voids immediately after the deposition of a given layer. The image processing system is built upon the YOLOv3 architecture and through moderate changes on anchor settings and achieves 53% precision on surface anomaly detection and 100% accuracy in identifying the fabricated components’ location, providing a prerequisite for high-precision assessment of welding quality. The work presented in this paper presents an inter-layer vision-based defect monitoring system in WAAM and serves to highlight the feasibility of developing such intelligent computer vision systems for monitoring the WAAM process for defects.
- Top Cited Papers
- 2 February 2022
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 120 (1-2) , 551-562
Vision-based melt pool monitoring for wire-arc additive manufacturing using deep learning method
- 2 February 2022
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 120 (1-2) , 551-562
Top Cited PapersVision-based melt pool monitoring for wire-arc additive manufacturing using deep learning method
- Open Access
- 28 December 2021
- Published by Springer Nature in Research Square
Towards Intelligent Monitoring System in Wire Arc Additive Manufacturing: A Surface Anomaly Detector on a Small Dataset
Rapid developments in artificial intelligence and image processing have presented many new opportunities for defect detection in manufacturing processes. In this work, an intelligent image processing system has been developed to monitor inter-layer deposition quality during a Wire Arc Additive Manufacturing (WAAM) process. Information produced from this system is to be used in conjunction with other quality monitoring systems to verify the quality of fabricated components. It is tailored to identify the presence of defects relating to lack-of-fusion and voids immediately after the deposition of a given layer. The image processing system is built upon the YOLOv3 architecture and through moderate changes on anchor settings, achieves 53% precision on surface anomaly detection and 100% accuracy in identifying the fabricated components’ location, providing a prerequisite for high precision assessment of welding quality. The work presented in this paper presents an inter-layer vision-based defect monitoring system in WAAM and serves to highlight the feasibility of developing such intelligent computer vision systems for monitoring the WAAM process for defects.
- 28 December 2021
- Published by Springer Nature in Research Square
Open AccessTowards Intelligent Monitoring System in Wire Arc Additive Manufacturing: A Surface Anomaly Detector on a Small Dataset
Rapid developments in artificial intelligence and image processing have presented many new opportunities for defect detection in manufacturing processes. In this work, an intelligent image processing system has been developed to monitor inter-layer deposition quality during a Wire Arc Additive Manufacturing (WAAM) process. Information produced from this system is to be used in conjunction with other quality monitoring systems to verify the quality of fabricated components. It is tailored to identify the presence of defects relating to lack-of-fusion and voids immediately after the deposition of a given layer. The image processing system is built upon the YOLOv3 architecture and through moderate changes on anchor settings, achieves 53% precision on surface anomaly detection and 100% accuracy in identifying the fabricated components’ location, providing a prerequisite for high precision assessment of welding quality. The work presented in this paper presents an inter-layer vision-based defect monitoring system in WAAM and serves to highlight the feasibility of developing such intelligent computer vision systems for monitoring the WAAM process for defects.
- Open Access
- 13 December 2021
- Published by Springer Nature in Research Square
Vision-Based Melt Pool Monitoring for Wire-Arc Additive Manufacturing Using Deep Learning Method
Wire-arc additive manufacturing (WAAM) technology has been widely recognized as a promising alternative for fabricating large-scale components, due to its advantages of high deposition rate and high material utilization rate. However, some anomalies may occur during the deposition process, such as humping, spattering, and robot suspend. this study proposed to apply Deep Learning in the visual monitoring to diagnose different anomalies during WAAM process. The melt pool images of different anomalies were collected for training and validation by a visual monitoring system. The classification performance of several representative CNN architectures, including ResNet, EfficientNet, VGG-16 and GoogLeNet, were investigated and compared. The classification accuracy of 97.62%, 97.45%, 97.15% and 97.25% was achieved by each model. The results proved that the CNN models are effective in classifying different types of melt pool images of WAAM. Our study is applicable beyond WAAM and should benefit other additive manufacturing or arc welding techniques.
- 13 December 2021
- Published by Springer Nature in Research Square
Open AccessVision-Based Melt Pool Monitoring for Wire-Arc Additive Manufacturing Using Deep Learning Method
Wire-arc additive manufacturing (WAAM) technology has been widely recognized as a promising alternative for fabricating large-scale components, due to its advantages of high deposition rate and high material utilization rate. However, some anomalies may occur during the deposition process, such as humping, spattering, and robot suspend. this study proposed to apply Deep Learning in the visual monitoring to diagnose different anomalies during WAAM process. The melt pool images of different anomalies were collected for training and validation by a visual monitoring system. The classification performance of several representative CNN architectures, including ResNet, EfficientNet, VGG-16 and GoogLeNet, were investigated and compared. The classification accuracy of 97.62%, 97.45%, 97.15% and 97.25% was achieved by each model. The results proved that the CNN models are effective in classifying different types of melt pool images of WAAM. Our study is applicable beyond WAAM and should benefit other additive manufacturing or arc welding techniques.
- Top Cited Papers
- 23 January 2021
- Published by Springer Nature in Journal of Intelligent Manufacturing
- Vol. 33 (5) , 1467-1482
Modelling and prediction of surface roughness in wire arc additive manufacturing using machine learning
- 23 January 2021
- Published by Springer Nature in Journal of Intelligent Manufacturing
- Vol. 33 (5) , 1467-1482
Top Cited PapersModelling and prediction of surface roughness in wire arc additive manufacturing using machine learning
- 1 October 2020
- Published by Elsevier in Journal of Manufacturing Processes
- Vol. 58, 179-186
Model predictive control of layer width in wire arc additive manufacturing
- 1 October 2020
- Published by Elsevier in Journal of Manufacturing Processes
- Vol. 58, 179-186
Model predictive control of layer width in wire arc additive manufacturing
- Top Cited Papers
- 1 October 2020
- Published by Elsevier in Journal of Manufacturing Systems
- Vol. 57, 31-45
A review on wire arc additive manufacturing: Monitoring, control and a framework of automated system
- 1 October 2020
- Published by Elsevier in Journal of Manufacturing Systems
- Vol. 57, 31-45
Top Cited PapersA review on wire arc additive manufacturing: Monitoring, control and a framework of automated system
- 3 September 2020
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 110 (7-8) , 2131-2142
Model-free adaptive iterative learning control of melt pool width in wire arc additive manufacturing
- 3 September 2020
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 110 (7-8) , 2131-2142
Model-free adaptive iterative learning control of melt pool width in wire arc additive manufacturing