WSWanliang Shan

Wanliang Shan

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Wanliang Shan has a total of 32 co-authors. Here are the top co-authors by number of shared publications:

  • Amir Mohammadi Nasab

    Department of Mechanical Engineering, University of Nevada, Reno, NV 89557, USA

    4 shared publications
  • Siavash Sharifi

    Shan Research Group Mechanical Engineering Department University of Nevada Reno, 1664 N. Virginia Street Reno NV 89557 USA

    4 shared publications
  • Amir Mohammadi Nasab

    Shan Research Group Mechanical Engineering Department University of Nevada Reno, 1664 N. Virginia Street Reno NV 89557 USA

    3 shared publications
  • Guangchao Wan

    Department of Mechanical and Aerospace Engineering Syracuse University Syracuse NY 13244 USA

    3 shared publications
  • Yanbing Tang

    Department of Mechanical and Aerospace Engineering Syracuse University Syracuse NY 13244 USA

    3 shared publications
  • Aoyi Luo

    Department of Mechanical Engineering and Applied Mechanics University of Pennsylvania 220 South 33rd Street Philadelphia PA 19104 USA

    2 shared publications

Latest Publications

  • Open Access

    Pick‐and‐Place Grippers with Tunable Adhesion from Capped Soft Hollow Pillar Structure

    by Yanbing Tang, Farshad Goodarzi, Guangchao Wan, Wanliang Shan

    Dynamically tunable dry adhesion has numerous applications in biological systems and industrial processes. Soft hollow pillars (SHPs) have demonstrated to have exceptional adhesion tunability under pneumatic actuation through sidewall buckling or bulging mechanisms. However, the adhesion strength of SHPs is significantly lower than that of solid elastomeric pillars, which can limit their practical use. In this study, mushroom‐shaped SHPs with a mushroom cap, or capped SHPs (C‐SHPs), are introduced to enhance the adhesion performance of soft grippers based on hollow pillar structures. Experiments and finite element modeling demonstrate that the cap significantly improves adhesion strength (1.8 to 2.9×) and adhesion tunability (∼1000×) by optimizing stress distribution and altering the crack initiation process at the contact interface. The effect of the cap size on the adhesion strength of C‐SHPs under various pressures is systematically investigated. Miniaturized SHPs and C‐SHPs are fabricated for pick‐and‐place manipulation of lightweight objects. An untethered device containing a C‐SHP is designed and assembled to highlight the energy‐efficient operation of C‐SHPs, with a ∼139 mJ energy consumption per pick‐and‐place cycle, showcasing their potential for applications in precision handling tasks. This work establishes C‐SHPs as a robust and adaptable solution for tunable dry adhesion systems.


  • Soft Shell Grippers with Highly Tunable Dry Adhesion through Low Negative Pressure for Universal Manipulation

    by Chenxu Zhao, Yanbing Tang, Kai‐Tak Wan, Wanliang Shan

    Highly tunable dry adhesion has practical ramifications in robotic manipulation. While grippers based on mechanical interlocking and suction are adopted in various industries, soft grippers that can handle small and delicate objects reliably are yet to be invented. In this paper, it is reported that the presence of an adhesive substrate against a negatively pressurized soft hemispherical shell can significantly delay buckling of the shell. The net adhesion strength of such a depressurized shell can reach 60 times that of an open shell without any pressure difference. Simultaneous measurements of internal pressure, mechanical tension, contact area, and approach distance agree well with a semi‐analytical solid‐mechanics model. Introduction of defects at the polar region of the shells does not affect adhesion under the depressurized condition but significantly reduces adhesion under no pressure, leading to even higher tunability (almost infinity). The enhanced adhesion of a depressurized shell is found to be a combined effect of dry adhesion and suction. These shell grippers are shown to be effective in the universal manipulation of various objects with wide ranges of weight, shape, surface roughness, and mechanical compliance. The proposed depressurized soft shells provide a promising robotic gripping platform for industrial adoption.


  • Tunable Dry Adhesion of Soft Hollow Pillars through Sidewall Buckling under Low Pressure

    by Guangchao Wan, Yanbing Tang, Kevin T. Turner, Teng Zhang, Wanliang Shan

    Controlling adhesion on demand is essential for many manufacturing and assembly processes such as microtransfer printing. Among various strategies, pneumatics‐controlled switchable adhesion is efficient and robust but currently still suffers from challenges in miniaturization and high energy cost. In this paper, a novel way to achieve tunable adhesion using low pressure by inducing sidewall buckling in soft hollow pillars (SHPs) is introduced. It is shown that the dry adhesion of these SHPs can be changed by more than two orders of magnitude (up to 151×) using low activating pressure (≈−10 or ≈20 kPa). Large enough negative pressure triggers sidewall buckling while positive pressure induces sidewall bulging, both of which can significantly change stress distribution at the bottom surface to facilitate crack initiation and reduce adhesion therein. It is shown that a single SHP can be activated by a micropump to manipulate various lightweight objects with different curvatures and surface textures. Here, it is also demonstrated that an array of SHPs can realize selective pick‐and‐place of an array of objects. These demonstrations illustrate the robustness, simplicity, and versatility of these SHPs with highly tunable dry adhesion.


  • Dynamically Tunable Dry Adhesion through a Subsurface Thin Layer with Tunable Stiffness

    by Amir Mohammadi Nasab, Patrick Stampfli, Siavash Sharifi, Aoyi Luo, Kevin T. Turner, Wanliang Shan

    Recently, a novel concept to realize dynamically tunable dry adhesion via subsurface stiffness modulation (SSM) in a composite core–shell structure has been introduced and demonstrated for gripping and release of objects. Here, a variant form of the composite core–shell design is proposed to significantly improve the performance of dynamically tunable dry adhesion in terms of activation time and activation voltage. Specifically, composite pillars with an embedded microfluidic channel filled with a low melting point alloy (LMPA) are fabricated, and the adhesion of the pillars is characterized as a function of LMPA state: either melted or solid. The effects of the thickness and in‐plane pattern of the LMPA channel, as well as the depth at which it is embedded on tunable adhesion are investigated. Experiments show that the effective adhesion strength can be reduced up to 50%, equivalent to a 2× change in dry adhesion when the LMPA is melted. Finite element analysis of the stress distribution change under SSM shows that the experimentally observed tunable adhesion is primarily due to stiffness change close to the interface. In addition, two technology demonstrations of composite pillars picking and releasing objects with fast activation (≈1 s) and low activation voltages (≈1 V) are included.


  • Robust Bicontinuous Elastomer–Metal Foam Composites with Highly Tunable Stiffness

    by Siavash Sharifi, Amir Mohammadi Nasab, Pei-En Chen, Yiliang Liao, Yang Jiao, Wanliang Shan

    Herein, a new class of robust bicontinuous elastomer–metal foam composites with highly tunable mechanical stiffness is proposed, fabricated, characterized, and demonstrated. The smart composite is a bicontinuous network of two foams, one metallic made of a low melting point alloy (LMPA) and the other elastomeric made of polydimethylsiloxane (PDMS). The stiffness of the composite can be tuned by inducing phase changes in its LMPA component. Below the melting point of the LMPA, Young's modulus of the smart composites is ≈1 GPa, whereas above the melting point of the LMPA it is ≈1 MPa. Thus, a sharp stiffness change of ≈1000× can be realized through the proposed bicontinuous foam composite structure, which is higher than all available robust smart composites. Effective medium theory is also used to predict the Young's modulus of the bicontinuous smart composites, which generates reasonable agreement with experimentally measured Young's modulus of the smart composites. Finally, the use of these smart materials as a smart joint in a robotic arm is also demonstrated.


  • Open Access

    Dynamically Tunable Friction via Subsurface Stiffness Modulation

    by Siavash Sharifi, Caleb Rux, Nathaniel Sparling, Guangchao Wan, Amir Mohammadi Nasab, Arpith Siddaiah, Pradeep Menezes, Teng Zhang, Wanliang Shan

    Currently soft robots primarily rely on pneumatics and geometrical asymmetry to achieve locomotion, which limits their working range, versatility, and other untethered functionalities. In this paper, we introduce a novel approach to achieve locomotion for soft robots through dynamically tunable friction to address these challenges, which is achieved by subsurface stiffness modulation (SSM) of a stimuli-responsive component within composite structures. To demonstrate this, we design and fabricate an elastomeric pad made of polydimethylsiloxane (PDMS), which is embedded with a spiral channel filled with a low melting point alloy (LMPA). Once the LMPA strip is melted upon Joule heating, the compliance of the composite structure increases and the friction between the composite surface and the opposing surface increases. A series of experiments and finite element analysis (FEA) have been performed to characterize the frictional behavior of these composite pads and elucidate the underlying physics dominating the tunable friction. We also demonstrate that when these composite structures are properly integrated into soft crawling robots inspired by inchworms and earthworms, the differences in friction of the two ends of these robots through SSM can potentially be used to generate translational locomotion for untethered crawling robots.


  • Open Access

    Robust Three‐Component Elastomer–Particle–Fiber Composites with Tunable Properties for Soft Robotics

    by Amir Mohammadi Nasab, Siavash Sharifi, Shuai Chen, Yang Jiao, Wanliang Shan

    Materials with tunable properties, especially dynamically tunable stiffness, have been of great interest for the field of soft robotics. Herein, a novel design concept of robust three‐component elastomer–particle–fiber composite system with tunable mechanical stiffness and electrical conductivity is introduced. These smart materials are capable of changing their mechanical stiffness rapidly and reversibly when powered with electrical current. One implementation of the composite system demonstrated here is composed of a polydimethylsiloxane (PDMS) matrix, Field's metal (FM) particles, and nickel‐coated carbon fibers (NCCF). It is demonstrated that the mechanical stiffness and the electrical conductivity of the composite are highly tunable and dependent on the volume fraction of the three components and the temperature, and can be reasonably estimated using effective medium theory. Due to its superior electrical conductivity, Joule heating can be used as the activation mechanism to realize ≈20× mechanical stiffness changes in seconds. The performance of the composites is thermally and mechanically robust. The shape memory effect of these composites is also demonstrated. The combination of tunable mechanical and electrical properties makes these composites promising candidates for sensing and actuation applications for soft robotics.


  • Adhesion of flat-ended pillars with non-circular contacts

    by Aoyi Luo, Amir Mohammadi Nasab, Milad Tatari, Shuai Chen, Wanliang Shan, Kevin T. Turner

    Adhesion of composite square and rectangular pillars are studied, and the highest adhesion is comparable to that of circular pillars.


  • Switchable Adhesion via Subsurface Pressure Modulation

    by Amir Mohammadi Nasab, Aoyi Luo, Siavash Sharifi, Kevin T. Turner, Wanliang Shan

    Materials and devices with tunable dry adhesion have many applications, including transfer printing, climbing robots, and gripping in pick-and-place processes. In this paper, a novel soft device to achieve dynamically tunable dry adhesion via modulation of sub-surface pneumatic pressure is introduced. Specifically, a cylindrical elastomer pillar with a mushroom-shaped cap and annular chamber that can be pressurized to tune the adhesion is investigated. Finite element-based mechanics models and experiments are used to design, understand, and demonstrate the adhesion of the device. Specifically, the device is designed using mechanics modelling such that the pressure applied inside the annular chamber significantly alters the stress distribution at the adhered interface and thus changes the effective adhesion strength. Devices made of polydimethylsiloxane (PDMS) with different elastic moduli were tested against glass, silicon, and aluminum substrates. Adhesion strengths (σ0) ranging from ~37 kPa (between PDMS and glass) to ~67 kPa (between PDMS and polished aluminum) are achieved for the unpressurized state. For all cases, regardless of the material and roughness of the substrates, the adhesion strength dropped to 40% of the strength of the unpressurized state (equivalent to a 2.5× adhesion switching ratio) by increasing the chamber pressure from 0.3σ0 to 0.6σ0. Furthermore, the strength drops to 20% of the unpressurized strength (equivalent to a 5× adhesion switching ratio) when the chamber pressure is increased to σ0.