Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Youqiang Wang has a total of 60 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Preparation and anti-icing/de-icing performance of HWCNTs/EP-M photothermal superhydrophobic coating

    by Guijing Guo, Youqiang Wang, Haiyang Zhang

    This work reports an HWCNTs/EP-M hybrid coating that combines robust durability with efficient ice-phobic properties (anti-icing and de-icing). By optimizing the mass ratio of carbon nanotubes to epoxy resin to 3:4, the resulting coating exhibited a water contact angle of 155.3°, confirming its superhydrophobic nature. Furthermore, under 1 kW/m 2 illumination, its surface temperature climbed swiftly to 66.9°C, demonstrating outstanding photothermal conversion. At −15°C, the droplet’s freezing time increased to 1038 s, whereas photothermal deicing achieved complete melting and detachment of the ice within 54 s. The superhydrophobic characteristics of the coating were preserved following mechanical abrasion, chemical corrosion, and high-temperature exposure, demonstrating its robustness. This coating, which combines efficient photothermal conversion, anti-icing/de-icing functionality, and long-term stability, offers a novel approach for developing energy-efficient anti-icing technologies.

  • TTCLNet: Ankle foot motion classification model based on wireless wearable sEMG and IMU sensors

    by Chang Li, Yi Zheng, Youqiang Wang, Shuyan Yang, Feiyang Wang, Qixin Guo, Runhao Liu, Hanyue Zhang

  • Open Access

    Investigation into the Impact of Water Contamination and Operating Parameters on the Lubrication Performance of Thrust Bearings

    by Bing Xue, Yongbo Li, Zhi Zhang, Yibing Ren, Ziyi Yang, Ying Xu, Tao Zhao, Youqiang Wang

    Water contamination threatens the lubrication stability of thrust bearings in hydro-generator units. This study investigates the coupling effects of inlet oil temperature, rotational speed, and water content (0–200 g/L) on lubrication performance. The results show that water content below 1 g/L has negligible effect. A critical threshold of 70 g/L is identified, where pad temperature rise rate increases sharply; at 45 °C inlet temperature, outlet zone temperature reaches 73 °C, and film thickness decreases to 12 μm. A water content of 100 g/L corresponds to the maximum friction torque of 9 N·m. Increasing rotational speed enhances hydrodynamic effects; at 25 m/s and 70 g/L, peak pad temperature reaches 72 °C. When water content exceeds 100 g/L, thermal buffering of free water mitigates temperature rise, but fluctuating oil film load-carrying capacity requires vigilance. The findings provide theoretical support for condition assessment and maintenance of thrust bearings under water-contaminated conditions.


  • Machining Performance Response of Inconel 718 Under High-Moderate-Low Cutting Speeds

    by Baoguo Zhang, Longxiang Liu, Chenbing Ni, Youqiang Wang, Dejian Liu, Wei Lu

    Nickel-based superalloy Inconel 718, renowned for its high yield strength and fatigue resistance at elevated temperatures, has found extensive application in various critical aviation structures, such as combustion chambers and turbine blades in aero engines. As the range of applications expands, the demand for machining Inconel 718 is increasing rapidly. However, it is the high strength and hardness of this alloy, along with its tendency to work harden, that make it difficult to cut. Therefore, it is crucial to examine how cutting speed influences the characteristics of 718 superalloy. This study systematically examined the influence of increasing cutting speed on key machining parameters, including cutting force, surface roughness, and microhardness. Additionally, a thorough analysis was performed on surface morphology and chip formation characteristics. As the cutting speed increases within the range of 20–100 m/min, both the surface roughness and cutting force exhibit an initial rise followed by a subsequent decline. Notably, the minimal cutting force is observed when the speed reaches 90 m/min, whereas the best surface finish is attained at 100 m/min. Additionally, a noticeable change in the chip morphology is also witnessed with the increase in cutting speed. Especially above 60 m/min, the chip shape gradually transitions from spiral to nonspiral arcuation chips, and the chip edges are observed to change from a continuous state to a periodic serrated state and then to a torn serrated state. This study can provide valuable guidance for high-efficiency and high-quality processing of Inconel 718.

  • Open Access

    Advances on Hydrogel Lubrication Modification Under Diverse Design Strategies

    by Ying Xu, Youqiang Wang, Kai An, Chenbing Ni, Haiyang Zhang, Yibing Ren, Ziyi Yang

    Hydrogel is a new type of lubricating material, and its lubrication performance is influenced by factors such as water content, chemical structure, cross-linking density, and friction pair materials. Currently, research on the lubrication performance of hydrogels has not formed a unified standard and system. Given that the lubricity of hydrogels mainly depends on their components and structure, as well as the chemical interactions between the polymer chains of the hydrogel network and the friction interface, this review systematically discusses the diverse design strategies of hydrogel lubricants based on the hydration and boundary lubrication mechanisms of gels, while elucidating the underlying enhancement mechanisms, as well as the corresponding tribological behavior and applications for different strategies. Finally, the main challenges and future research directions are underlined, aiming to provide theoretical and technical support for the design optimization and practical application of advanced hydrogel lubrication materials.


  • Effect of Aging Treatments on the Nanoprecipitation Mechanism and Dynamic Impact Behavior of Mg-7.5Gd-3Y-0.5Zr Alloy

    by Xuezhao Wang, Ping Zhang, Xiaomin Jiang, Youqiang Wang

    This study aims to enhance the dynamic impact mechanical properties of Mg-7.5Gd-3Y-0.5Zr alloy by investigating the effects of aging treatments on its microstructure and dynamic impact behavior. Using various techniques, including metallographic observation, scanning electron microscopy (SEM), energy-dispersive spectroscopy (EDS), transmission electron microscopy (TEM), electron backscatter diffraction (EBSD), microhardness testing and split-Hopkinson pressure bar tests, the microstructural and macroscopic static-dynamic properties of the alloy under different aging conditions were thoroughly examined. The findings indicate the following: The aging treatments identified based on hardness curves and TEM analysis include under-aging ([ ], peak-aging ([ ] and over-aging ([ ], with specific conditions of 225[ ]C for 3[ ]h, 225[ ]C for 12[ ]h and 350[ ]C for 12[ ]h, respectively. The alloy exhibits a maximum impact strength of 560 MPa[ ]under under-aging conditions. Under peak aging, the maximum impact strength increases to 596 MPa. The optimal impact strength under over-aging conditions is 558 MPa[ ]. The deformation mechanisms of the alloy under under-aging conditions are characterized by a combination of tensile and compressive twinning. In contrast, peak-aging and over-aging conditions primarily involve tensile twinning, with compressive twinning playing a secondary role. The fracture mechanisms of the alloy under various aging states are mainly a mix of ductile and brittle fractures. However, in the under-aged sample, the volume fraction of the dimples is significantly more than that of cleavage planes, which ductile-brittle mixed fracture dominated by ductile fracture; for the peak-aging alloy, the number of cleavage planes increases, showing ductile-brittle mixed fracture dominated by brittle fracture.

  • Open Access

    Surface Integrity and Machining Mechanism of Al 7050 Induced by Multi-Physical Field Coupling in High-Speed Machining

    by Wei Lu, Chenbing Ni, Youqiang Wang, Chengguo Zong, Dejian Liu, Xingbao Huang

    Improving the surface quality and controlling the microstructure evolution of difficult-to-cut materials are always challenges in high-speed machining (HSM). In this paper, surface topography, defects and roughness are assessed to characterize the surface features of 7050 aluminum alloy (Al 7050) under HSM conditions characterized by high temperature, strain and strain rate. Based on multi-physical field coupling, the mechanism of microstructure evolution of Al 7050 is investigated in HSM. The results indicate that the surface morphology and roughness of Al7050 during HSM are optimal at fz = 0.025 mm/z, and the formation of surface defects (adherent chips, cavities, microcracks, material compression and tearing) in HSM is mainly affected by thermo-mechanical coupling. Significant differences are observed in the microstructure of different machined subsurfaces by electron backscatter diffraction (EBSD) technology, and high cutting speeds and high feed rates contributed to recrystallization. The crystallographic texture types on machined subsurface are mainly {110} Brass texture, {001} Cube texture, {123} S texture and {124} R texture, and the crystallographic texture type and intensity are significantly affected by multi-physical field coupling. The elastic–plastic deformation and microstructural evolution of Al7050 alloy during the HSM process are mainly influenced by the coupling effects of multiple physical fields (stress–strain field and thermo-mechanical coupling field). This study reveals the internal mechanism of multi-physical field coupling in HSM and provides valuable enlightenment for the control of microstructure evolution of difficult-to-cut materials in HSM.