Arumugam Sivaprakasam
Research Subjects
Arumugam Sivaprakasam has a total of 14 co-authors. Here are the top co-authors by number of shared publications:
- E. Nandhini
Research scholar, College of Engineering Guindy, Anna University, Chennai, India
2 shared publications - Jd Anunciya
Department of Mechanical, Industrial and Electrical Engineering, Namibia University of Science and Technology, Windhoek, Namibia
2 shared publications - Naveen Kumar Elangovan
Department of Electrical and Electronics Engineering, Council for Scientific and Industrial Research, Anna University, Chennai, India
2 shared publications - Ramaswamy Bharani
Prathyusha Institute of Technology and Management
2 shared publications Bhavani Somasundaram
Marine Engineering, GKMCET, Chennai-600063, India
1 shared publication- Chinnappa Rani
School of Electrical Engineering, Vellore Institute of Technology, Vellore, India
1 shared publication
Latest Publications
- Open Access
- 30 August 2025
- Published by Editura Academiei Române in REVUE ROUMAINE DES SCIENCES TECHNIQUES — SÉRIE ÉLECTROTECHNIQUE ET ÉNERGÉTIQUE
- Vol. 70 (3) , 331-336
SLIDING MODE CONTROLLED CLOSED LOOP QB-CONVERTER -TPIS FED PMSM DRIVE WITH ENHANCED RESPONSE
The primary goal of this work is to identify the most appropriate controller for a QBC-TPIS fed PMSMD used high performance drives. A drive requires fast dynamic response and accurate control for its operation. This effort deals with the design, analysis &simulation of Closed loop- Quadratic Boost (QB) Converter-TPIS (Three Phase Inverter System) fed PMSM (Permanent Magnet Synchronous Motors) with Proportional-Integral (PI) & SM (Sliding mode) controller outcomes are presented. In this work duty cycle optimization of Q-Boost Converter was done by control input of SM controller. The-consequences are related in terms of-time-domain aspects like –rise-time,-peak-time,-settling-time&- steady state error. Settling time is lowered to 2s and steady-state error in speed is also reduced to 1.98rpm in Sliding Mode (SM) control. The consequence denotes the-better outcomes of Closed- loop-Quadratic-BC-TPIS fed PMSMD with SM controller.
- 30 August 2025
- Published by Editura Academiei Române in REVUE ROUMAINE DES SCIENCES TECHNIQUES — SÉRIE ÉLECTROTECHNIQUE ET ÉNERGÉTIQUE
- Vol. 70 (3) , 331-336
Open AccessSLIDING MODE CONTROLLED CLOSED LOOP QB-CONVERTER -TPIS FED PMSM DRIVE WITH ENHANCED RESPONSE
The primary goal of this work is to identify the most appropriate controller for a QBC-TPIS fed PMSMD used high performance drives. A drive requires fast dynamic response and accurate control for its operation. This effort deals with the design, analysis &simulation of Closed loop- Quadratic Boost (QB) Converter-TPIS (Three Phase Inverter System) fed PMSM (Permanent Magnet Synchronous Motors) with Proportional-Integral (PI) & SM (Sliding mode) controller outcomes are presented. In this work duty cycle optimization of Q-Boost Converter was done by control input of SM controller. The-consequences are related in terms of-time-domain aspects like –rise-time,-peak-time,-settling-time&- steady state error. Settling time is lowered to 2s and steady-state error in speed is also reduced to 1.98rpm in Sliding Mode (SM) control. The consequence denotes the-better outcomes of Closed- loop-Quadratic-BC-TPIS fed PMSMD with SM controller.
- Open Access
Dual Mode Symmetrical Proportional Resonant Controlled Quadratic Boost Converter for PMSM-Drive
Power electronics-based converters have been widely used in several applications, specifically electric propulsion systems. Ongoing advancements in converters have led to high-gain Quadratic Boost Converters (QBC) which control Permanent Magnet Synchronous Motor (PMSM) drive. In this work, a novel scheme is employed, particularly a three-phase inverter between QBC and PMSM operated by a dual-mode controller strategy. Precisely, the novelty of this work is to use the quadratic boost converter to control the PMSM drive by applying different control strategies. This work also demonstrates the simulation of two different current control strategies applied to a Semi-Converter (SC) fed QBC based on PMSM-based EV. It also presents the strategy, inquiry, and model of SC-based QBC three-phase inverter (TPI) fed PMSM with symmetrical operated PI (Proportional Integral), FOPID (Fractional Order Proportional Integral Derivative), and PR (Proportional Resonant) controllers. The simulated results offer a significant improvement in PMSM parameters compared with the PI-PI framework, notably voltage, speed, and torque against source disturbances. Further, the PR-PR control approach provides better time-domain parameters than the PI-PI control strategy (including the least rise time (Tr) of 1.15 s, peak time (Tp) of 2.38 s, settling time (Ts) of 4.12 s, and steady-state error (Ess) of 4.89 s). Furthermore, the experimental module is designed to test the effectiveness of the proposed control strategies and was found to be more advantageous in dual mode symmetric PR-PR controlled SC-based QBC-TPI fed PMSM.
Open AccessDual Mode Symmetrical Proportional Resonant Controlled Quadratic Boost Converter for PMSM-Drive
Power electronics-based converters have been widely used in several applications, specifically electric propulsion systems. Ongoing advancements in converters have led to high-gain Quadratic Boost Converters (QBC) which control Permanent Magnet Synchronous Motor (PMSM) drive. In this work, a novel scheme is employed, particularly a three-phase inverter between QBC and PMSM operated by a dual-mode controller strategy. Precisely, the novelty of this work is to use the quadratic boost converter to control the PMSM drive by applying different control strategies. This work also demonstrates the simulation of two different current control strategies applied to a Semi-Converter (SC) fed QBC based on PMSM-based EV. It also presents the strategy, inquiry, and model of SC-based QBC three-phase inverter (TPI) fed PMSM with symmetrical operated PI (Proportional Integral), FOPID (Fractional Order Proportional Integral Derivative), and PR (Proportional Resonant) controllers. The simulated results offer a significant improvement in PMSM parameters compared with the PI-PI framework, notably voltage, speed, and torque against source disturbances. Further, the PR-PR control approach provides better time-domain parameters than the PI-PI control strategy (including the least rise time (Tr) of 1.15 s, peak time (Tp) of 2.38 s, settling time (Ts) of 4.12 s, and steady-state error (Ess) of 4.89 s). Furthermore, the experimental module is designed to test the effectiveness of the proposed control strategies and was found to be more advantageous in dual mode symmetric PR-PR controlled SC-based QBC-TPI fed PMSM.
- 9 January 2022
- Published by SAGE Publications in Transactions of the Institute of Measurement and Control
- Vol. 44 (9) , 1887-1903
A computationally efficient torque and flux ripple reduction by active vector optimization approach using direct torque control–based model predictive torque control for matrix converter–fed permanent magnet synchronous motor
The Matrix Converter–fed Finite Control Set–Model Predictive Control is an efficient drive control approach that exhibits numerous advantageous features. However, it is computationally expensive as it employs all the available matrix converter voltage vectors for the prediction and estimation. The computational complexity increases further with respect to the inclusion of additional control objectives in the cost function which degrades the potentiality of this technique. This paper proposes two computationally effective switching tables for simplifying the calculation process and optimizing the matrix converter active prediction vectors. Here, three prediction active vectors are selected out of 18 vectors by considering the torque and flux errors of the permanent magnet synchronous motor. In addition, the voltage vector location segments are modified into 12 sectors to boost the torque dynamic control. The performance superiority of the proposed concept is analyzed using the MATLAB/Simulink software and the real-time validation is conducted by implementing in the real-time OPAL-RT lab setup.
- 9 January 2022
- Published by SAGE Publications in Transactions of the Institute of Measurement and Control
- Vol. 44 (9) , 1887-1903
A computationally efficient torque and flux ripple reduction by active vector optimization approach using direct torque control–based model predictive torque control for matrix converter–fed permanent magnet synchronous motor
The Matrix Converter–fed Finite Control Set–Model Predictive Control is an efficient drive control approach that exhibits numerous advantageous features. However, it is computationally expensive as it employs all the available matrix converter voltage vectors for the prediction and estimation. The computational complexity increases further with respect to the inclusion of additional control objectives in the cost function which degrades the potentiality of this technique. This paper proposes two computationally effective switching tables for simplifying the calculation process and optimizing the matrix converter active prediction vectors. Here, three prediction active vectors are selected out of 18 vectors by considering the torque and flux errors of the permanent magnet synchronous motor. In addition, the voltage vector location segments are modified into 12 sectors to boost the torque dynamic control. The performance superiority of the proposed concept is analyzed using the MATLAB/Simulink software and the real-time validation is conducted by implementing in the real-time OPAL-RT lab setup.
- 30 November 2021
- Published by Taylor & Francis in IETE Journal of Research
- Vol. 69 (9) , 1-10
30° Discontinuous PWM-Based Closed Loop Volts/Hz Control of Induction Motor Drive with Slip Regulation
This paper proposes 30° discontinuous PWM-based closed loop volts/Hz control of induction motor drive with slip regulation. The voltage source inverter is carried out with various pulse width modulation (PWM) schemes such as continuous PWM (CPWM) and discontinuous PWM (DPWM) schemes. The inverter's performance is affected by these PWM schemes. Therefore, this paper investigates the PWM schemes for the inverter. It aims to identify a best PWM scheme based on the total harmonic distortion and torque ripple analysis for constant volts/Hz induction motor drive amongst the various PWM schemes in open loop and closed loop and also proposes a 30° DPWM-based closed-loop control. The performance investigations of various PWM schemes based on inverter-fed induction motor have been evaluated analytically and using MATLAB/Simulink environment. Experimental results have been validated. The combination of 30° DPWM with PI control and slip regulation for induction motor makes the speed control system robust and ideal for low-accuracy applications.
- 30 November 2021
- Published by Taylor & Francis in IETE Journal of Research
- Vol. 69 (9) , 1-10
30° Discontinuous PWM-Based Closed Loop Volts/Hz Control of Induction Motor Drive with Slip Regulation
This paper proposes 30° discontinuous PWM-based closed loop volts/Hz control of induction motor drive with slip regulation. The voltage source inverter is carried out with various pulse width modulation (PWM) schemes such as continuous PWM (CPWM) and discontinuous PWM (DPWM) schemes. The inverter's performance is affected by these PWM schemes. Therefore, this paper investigates the PWM schemes for the inverter. It aims to identify a best PWM scheme based on the total harmonic distortion and torque ripple analysis for constant volts/Hz induction motor drive amongst the various PWM schemes in open loop and closed loop and also proposes a 30° DPWM-based closed-loop control. The performance investigations of various PWM schemes based on inverter-fed induction motor have been evaluated analytically and using MATLAB/Simulink environment. Experimental results have been validated. The combination of 30° DPWM with PI control and slip regulation for induction motor makes the speed control system robust and ideal for low-accuracy applications.
- Open Access
Buck-Boost Single-Stage Microinverter for Building Integrated Photovoltaic Systems
Microinverters for Building Integrated Photovoltaic (BIPV) systems must have had a small number of components, be efficient, and be reliable. In this context, a single-phase Buck-Boost Single-stage Microinverter (BBSM) for grid-connected BIPV systems is presented. The concept of topology is extracted from the buck-boost converter. The leakage current in the system is kept under control. It uses an optimal number of active and passive components to function at a high-efficiency level. The suggested topology provides a high level of reliability due to the absence of shoot-through problems. To validate the findings, a simulation in combination with an experimental system for a 70 W system is developed with the design approach. The efficiency of the microinverter, total harmonic distortion of the grid current are measured as 96.4% and 4.09% respectively. Finally, a comparison study has indicated the advantages and disadvantages of the suggested inverter.
Open AccessBuck-Boost Single-Stage Microinverter for Building Integrated Photovoltaic Systems
Microinverters for Building Integrated Photovoltaic (BIPV) systems must have had a small number of components, be efficient, and be reliable. In this context, a single-phase Buck-Boost Single-stage Microinverter (BBSM) for grid-connected BIPV systems is presented. The concept of topology is extracted from the buck-boost converter. The leakage current in the system is kept under control. It uses an optimal number of active and passive components to function at a high-efficiency level. The suggested topology provides a high level of reliability due to the absence of shoot-through problems. To validate the findings, a simulation in combination with an experimental system for a 70 W system is developed with the design approach. The efficiency of the microinverter, total harmonic distortion of the grid current are measured as 96.4% and 4.09% respectively. Finally, a comparison study has indicated the advantages and disadvantages of the suggested inverter.
- 5 June 2021
- Published by Springer Nature in Journal of Materials Science: Materials in Electronics
- Vol. 32 (13) , 17612-17619
Effect of CdS thin film on the performance of methylammonium lead iodide perovskite solar cell
- 5 June 2021
- Published by Springer Nature in Journal of Materials Science: Materials in Electronics
- Vol. 32 (13) , 17612-17619
Effect of CdS thin film on the performance of methylammonium lead iodide perovskite solar cell
- 12 October 2020
- Published by Taylor & Francis in Molecular Crystals and Liquid Crystals
- Vol. 710 (1) , 66-73
Investigation of parameters affecting the performance of Perovskite solar cells
The study focuses on optoelectronic model of perovskite solar cell using finite element method to optimize the thickness of electron transport and absorber layers implemented using COMSOL multi-physics modeling. The analyzed perovskite solar cell shows a power conversion efficiency of 17.95% for an optimum film thickness of TiO2 (90 nm)/CH3NH3PbI3 (100 nm)/Spiro-OMeTAD (300 nm). The obtained simulated results were examined to improve the efficiency of the device and also to understand the impact of factors affecting the performance of the solar cell. Furthermore, the working potential of perovskite solar cell was explored to demonstrate the impending scope of stepwise progress in the novel technology.
- 12 October 2020
- Published by Taylor & Francis in Molecular Crystals and Liquid Crystals
- Vol. 710 (1) , 66-73
Investigation of parameters affecting the performance of Perovskite solar cells
The study focuses on optoelectronic model of perovskite solar cell using finite element method to optimize the thickness of electron transport and absorber layers implemented using COMSOL multi-physics modeling. The analyzed perovskite solar cell shows a power conversion efficiency of 17.95% for an optimum film thickness of TiO2 (90 nm)/CH3NH3PbI3 (100 nm)/Spiro-OMeTAD (300 nm). The obtained simulated results were examined to improve the efficiency of the device and also to understand the impact of factors affecting the performance of the solar cell. Furthermore, the working potential of perovskite solar cell was explored to demonstrate the impending scope of stepwise progress in the novel technology.
- 11 June 2020
- Published by SAGE Publications in Journal of Vibration and Control
- Vol. 27 (7-8) , 879-892
A new approach to minimize torque ripple and noise in model predictive control of permanent magnet synchronous motor drives
Model predictive control widely advocates in the better performance control technique for permanent magnet synchronous motor drives for its exceptional flexibility of incorporating nonlinear parameters. However, the higher ripples in torque and harmonics in stator current are the major criticisms in this method. Enlightened by the idea of including nonlinear constraints in the cost function, this article proposes a novel cost function with reduced ripples in torque, stator flux, and current harmonics. The improvised cost function uses torque tracking, maximum torque per ampere, minimization of switching losses, and system constraints. This approach attains effectiveness in the minimization of the ripples in torque, stator flux, and stator current harmonics and also reduces the acoustic noise of the system. The claims of the proposed work are supported by the quantitative comparison of the simulated response with the standard model predictive torque control that uses errors in the stator flux and electromagnetic torque in its cost function. The compared simulation results prove the effectiveness of the proposed control technique.
- 11 June 2020
- Published by SAGE Publications in Journal of Vibration and Control
- Vol. 27 (7-8) , 879-892
A new approach to minimize torque ripple and noise in model predictive control of permanent magnet synchronous motor drives
Model predictive control widely advocates in the better performance control technique for permanent magnet synchronous motor drives for its exceptional flexibility of incorporating nonlinear parameters. However, the higher ripples in torque and harmonics in stator current are the major criticisms in this method. Enlightened by the idea of including nonlinear constraints in the cost function, this article proposes a novel cost function with reduced ripples in torque, stator flux, and current harmonics. The improvised cost function uses torque tracking, maximum torque per ampere, minimization of switching losses, and system constraints. This approach attains effectiveness in the minimization of the ripples in torque, stator flux, and stator current harmonics and also reduces the acoustic noise of the system. The claims of the proposed work are supported by the quantitative comparison of the simulated response with the standard model predictive torque control that uses errors in the stator flux and electromagnetic torque in its cost function. The compared simulation results prove the effectiveness of the proposed control technique.
- 12 May 2020
- Published by Taylor & Francis in IETE Journal of Research
- Vol. 68 (5) , 3187-3201
A Review of Various Control Strategies Based on Space Vector Pulse Width Modulation for the Voltage Source Inverter
Voltage source inverters are the most preferred in a variety of medium and high power applications. The control of inverter output voltage gives desirable outputs in drives and many applications. Pulse width modulation (PWM) techniques strongly influence the inverter output. Space vector pulse width modulation (SVPWM) technique is one among the prominent techniques that are used for inverter switching control. This paper is devoted to the review of variety of control strategies on SVPWM evolved over the past 20 years and its thrust on the output voltage of inverter and current with the description of the various sequences and its behaviour for both two-level and three-level inverter for an induction motor drive. The various PWM control strategies based on Space vector PWM are categorized as follows: Bus Clamping PWM, Advanced Bus Clamping PWM, and Hybrid PWM. The merits and demerits of each SVPWM techniques are presented by analysing the experimental results from the literature. SVPWM can also be achieved by triangular comparison approach other than space vector approach which is meritorious in some aspects like lower computation and memory requirements. This paper also deals with the review of space vector PWM on triangular comparison approach which is termed as carrier-based SVPWM.
- 12 May 2020
- Published by Taylor & Francis in IETE Journal of Research
- Vol. 68 (5) , 3187-3201
A Review of Various Control Strategies Based on Space Vector Pulse Width Modulation for the Voltage Source Inverter
Voltage source inverters are the most preferred in a variety of medium and high power applications. The control of inverter output voltage gives desirable outputs in drives and many applications. Pulse width modulation (PWM) techniques strongly influence the inverter output. Space vector pulse width modulation (SVPWM) technique is one among the prominent techniques that are used for inverter switching control. This paper is devoted to the review of variety of control strategies on SVPWM evolved over the past 20 years and its thrust on the output voltage of inverter and current with the description of the various sequences and its behaviour for both two-level and three-level inverter for an induction motor drive. The various PWM control strategies based on Space vector PWM are categorized as follows: Bus Clamping PWM, Advanced Bus Clamping PWM, and Hybrid PWM. The merits and demerits of each SVPWM techniques are presented by analysing the experimental results from the literature. SVPWM can also be achieved by triangular comparison approach other than space vector approach which is meritorious in some aspects like lower computation and memory requirements. This paper also deals with the review of space vector PWM on triangular comparison approach which is termed as carrier-based SVPWM.