Tatyana S. Struchkova
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Tatyana S. Struchkova has a total of 13 co-authors. Here are the top co-authors by number of shared publications:
- Aitalina Alekseevna Okhlopkova
Chemical Department, Institute of Natural Sciences, North-Eastern Federal University, Yakutsk 677000, Russia
3 shared publications - Andrey P. Vasilev
North-Eastern Federal University
3 shared publications - Sakhayana Nikolaevna Danilova
Institute of Natural Sciences North‐Eastern Federal University Yakutsk Russia
2 shared publications A.A. Okhlopkova
1 shared publicationA.G. Alekseev
1 shared publicationA.P. Vasilev
1 shared publication
Latest Publications
- Open Access
Mechanical and Tribological Properties of Polytetrafluoroethylene Modified with Combined Fillers: Carbon Fibers, Zirconium Dioxide, Silicon Dioxide and Boron Nitride
The introduction of combined fillers can effectively improve the mechanical and tribological properties of polytetrafluoroethylene (PTFE). In this work, three different types of nanosized fillers (zirconium dioxide, silicon dioxide, and boron nitride) were introduced in a carbon fiber-reinforced polymer matrix for the development of polymer composite materials (PCM). Tensile and compressive testing were carried out, and the hardness of created PCM was evaluated. It is shown that the compressive strength of PCM increased by 30–70%, and the hardness, increased by 38–55% compared to the initial PTFE. The tribological properties of the developed PCM were evaluated under dry friction conditions. An analysis of the results of an experimental study of wear confirmed that the inclusion of combined fillers (two- and three-component) in PTFE significantly increased wear resistance compared to the polymer matrix with a slight increase in the coefficient of friction. It has been shown that the introduction of three-component fillers has an antagonistic effect on the wear resistance of PCMs compared to two-component fillers. The thermodynamic properties of the composites were analyzed by differential scanning calorimetry and a thermomechanical analyzer. The surface morphology of polymer composites after wear testing was studied by IR spectroscopy and scanning electron microscopy to investigate and suggest a possible mechanism for increasing the wear resistance of the developed composites.
Open AccessMechanical and Tribological Properties of Polytetrafluoroethylene Modified with Combined Fillers: Carbon Fibers, Zirconium Dioxide, Silicon Dioxide and Boron Nitride
The introduction of combined fillers can effectively improve the mechanical and tribological properties of polytetrafluoroethylene (PTFE). In this work, three different types of nanosized fillers (zirconium dioxide, silicon dioxide, and boron nitride) were introduced in a carbon fiber-reinforced polymer matrix for the development of polymer composite materials (PCM). Tensile and compressive testing were carried out, and the hardness of created PCM was evaluated. It is shown that the compressive strength of PCM increased by 30–70%, and the hardness, increased by 38–55% compared to the initial PTFE. The tribological properties of the developed PCM were evaluated under dry friction conditions. An analysis of the results of an experimental study of wear confirmed that the inclusion of combined fillers (two- and three-component) in PTFE significantly increased wear resistance compared to the polymer matrix with a slight increase in the coefficient of friction. It has been shown that the introduction of three-component fillers has an antagonistic effect on the wear resistance of PCMs compared to two-component fillers. The thermodynamic properties of the composites were analyzed by differential scanning calorimetry and a thermomechanical analyzer. The surface morphology of polymer composites after wear testing was studied by IR spectroscopy and scanning electron microscopy to investigate and suggest a possible mechanism for increasing the wear resistance of the developed composites.
- Open Access
- 28 December 2021
- Published by MDPI AG in Lubricants
- Vol. 10 (1) , 4
Mechanical and Tribological Properties of Polytetrafluoroethylene Composites Modified by Carbon Fibers and Zeolite
Currently, lightweight and high-strength polymer composites can provide weight savings in the automotive and process equipment industries by replacing metal parts. Polytetrafluoroethylene and polymer composites based on it are used in various tribological applications due to their excellent antifriction properties and thermal stability. This article examines the effect of combined fillers (carbon fibers and zeolite) on the mechanical, tribological properties, and structure of polytetrafluoroethylene. It is shown that the introduction of combined fillers into polytetrafluoroethylene retains the tensile strength and elongation at break at a content of 1–5 wt.% of carbon fibers, the compressive stress increased by 53%, and the yield stress increased by 45% relative to the initial polymer. The wear resistance of polymer composites increased 810-fold compared to the initial polytetrafluoroethylene while maintaining a low coefficient of friction. The structural features of polymer composites are characterized by X-ray diffraction analysis, infrared spectroscopy, and scanning electron microscopy.
- 28 December 2021
- Published by MDPI AG in Lubricants
- Vol. 10 (1) , 4
Open AccessMechanical and Tribological Properties of Polytetrafluoroethylene Composites Modified by Carbon Fibers and Zeolite
Currently, lightweight and high-strength polymer composites can provide weight savings in the automotive and process equipment industries by replacing metal parts. Polytetrafluoroethylene and polymer composites based on it are used in various tribological applications due to their excellent antifriction properties and thermal stability. This article examines the effect of combined fillers (carbon fibers and zeolite) on the mechanical, tribological properties, and structure of polytetrafluoroethylene. It is shown that the introduction of combined fillers into polytetrafluoroethylene retains the tensile strength and elongation at break at a content of 1–5 wt.% of carbon fibers, the compressive stress increased by 53%, and the yield stress increased by 45% relative to the initial polymer. The wear resistance of polymer composites increased 810-fold compared to the initial polytetrafluoroethylene while maintaining a low coefficient of friction. The structural features of polymer composites are characterized by X-ray diffraction analysis, infrared spectroscopy, and scanning electron microscopy.
- Open Access
Mechanical and Tribological Properties of Polytetrafluoroethylene Composites with Carbon Fiber and Layered Silicate Fillers
Mixtures of layered silicates (vermiculite and kaolinite) and carbon fibers were investigated as filler materials for polytetrafluoroethylene. The supramolecular structure and the tribological and mechanical properties of the resulting polymer composite materials were evaluated. The yield strength and compressive strength of the polymer increased by 55% and 60%, respectively, when a mixed filler was used, which was attributed to supramolecular reinforcement of the composites. In addition, the wear resistance increased by 850 times when using vermiculite/kaolinite fillers, which was due to protection of the surface by the formation of hard tribofilms.
Open AccessMechanical and Tribological Properties of Polytetrafluoroethylene Composites with Carbon Fiber and Layered Silicate Fillers
Mixtures of layered silicates (vermiculite and kaolinite) and carbon fibers were investigated as filler materials for polytetrafluoroethylene. The supramolecular structure and the tribological and mechanical properties of the resulting polymer composite materials were evaluated. The yield strength and compressive strength of the polymer increased by 55% and 60%, respectively, when a mixed filler was used, which was attributed to supramolecular reinforcement of the composites. In addition, the wear resistance increased by 850 times when using vermiculite/kaolinite fillers, which was due to protection of the surface by the formation of hard tribofilms.
- Open Access
- 12 October 2016
- Published by Knowledge E DMCC in KnE Materials Science
- Vol. 1 (1) , 155-160
Influence of Carbon Fibers on Structure and Properties of Polytetrafluoroethylene
In this paper, we studied the effect of carbon fibers on the performance properties of polymer composites based on polytetrafluoroethylene. It was shown that the introduction of PTFE carbon fibers significantly improved tribological and mechanical properties of the composite. The correlation between the performance properties and supramolecular structure was found. Initial lamellar structure of the polymer became less in size without significant changes in morphology when filled. Such process was accompanied by the increase of crystalline regions number and the crystallinity degree of composite. Structural studies have shown that materials with more densely packed and highly crystalline structure have increased mechanical and tribological properties. The developed materials can be used in friction units of machines and devices, where the use of lubricants is not acceptable or restricted.
- 12 October 2016
- Published by Knowledge E DMCC in KnE Materials Science
- Vol. 1 (1) , 155-160
Open AccessInfluence of Carbon Fibers on Structure and Properties of Polytetrafluoroethylene
In this paper, we studied the effect of carbon fibers on the performance properties of polymer composites based on polytetrafluoroethylene. It was shown that the introduction of PTFE carbon fibers significantly improved tribological and mechanical properties of the composite. The correlation between the performance properties and supramolecular structure was found. Initial lamellar structure of the polymer became less in size without significant changes in morphology when filled. Such process was accompanied by the increase of crystalline regions number and the crystallinity degree of composite. Structural studies have shown that materials with more densely packed and highly crystalline structure have increased mechanical and tribological properties. The developed materials can be used in friction units of machines and devices, where the use of lubricants is not acceptable or restricted.