Shaozhen Hua
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Shaozhen Hua has a total of 12 co-authors. Here are the top co-authors by number of shared publications:
- Binbin Dong
Key Laboratory of Materials Processing and Mold (Zhengzhou University), Ministry of Education, National Engineering Research Center for Advanced Polymer Processing Technology, Zhengzhou University, Zhengzhou, China
1 shared publication - Changyu Shen
School of Materials Science and Engineering, National Engineering Research Center for Advanced Polymer Processing Technology, Zhengzhou University, Zhengzhou 450001, China
1 shared publication - Chunguang Shao
National Engineering Research Center for Advanced Polymer Processing Technology
1 shared publication - Chuntai Liu
Zhengzhou University
1 shared publication - Fanjing Meng
Henan Institute of Technology
1 shared publication - Shixun Zhang
National Engineering Research Center of Mold & Die , Zhengzhou University , Zhengzhou , Henan, 450002 ; Key Laboratory of Materials Processing and Molding (Ministry of Education) , Zhengzhou University , Zhengzhou, Henan, 450002
1 shared publication
Latest Publications
- 12 February 2024
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 34 (3) , 2390-2397
Investigation of the Mechanical and Tribological Properties of Diamond-Like Carbon Films on YG8 and High-Speed Steel Substrates with W Buffer Layers
- 12 February 2024
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 34 (3) , 2390-2397
Investigation of the Mechanical and Tribological Properties of Diamond-Like Carbon Films on YG8 and High-Speed Steel Substrates with W Buffer Layers
- 28 February 2019
- Published by Springer Nature in Journal of the Brazilian Society of Mechanical Sciences and Engineering
- Vol. 41 (3) , 153
Fluctuation and self-diffusion research about dry granular materials under shearing
- 28 February 2019
- Published by Springer Nature in Journal of the Brazilian Society of Mechanical Sciences and Engineering
- Vol. 41 (3) , 153
Fluctuation and self-diffusion research about dry granular materials under shearing
- Open Access
Simulation of Jetting in Injection Molding Using a Finite Volume Method
In order to predict the jetting and the subsequent buckling flow more accurately, a three dimensional melt flow model was established on a viscous, incompressible, and non-isothermal fluid, and a control volume-based finite volume method was employed to discretize the governing equations. A two-fold iterative method was proposed to decouple the dependence among pressure, velocity, and temperature so as to reduce the computation and improve the numerical stability. Based on the proposed theoretical model and numerical method, a program code was developed to simulate melt front progress and flow fields. The numerical simulations for different injection speeds, melt temperatures, and gate locations were carried out to explore the jetting mechanism. The results indicate the filling pattern depends on the competition between inertial and viscous forces. When inertial force exceeds the viscous force jetting occurs, then it changes to a buckling flow as the viscous force competes over the inertial force. Once the melt contacts with the mold wall, the melt filling switches to conventional sequential filling mode. Numerical results also indicate jetting length increases with injection speed but changes little with melt temperature. The reasonable agreements between simulated and experimental jetting length and buckling frequency imply the proposed method is valid for jetting simulation.
Open AccessSimulation of Jetting in Injection Molding Using a Finite Volume Method
In order to predict the jetting and the subsequent buckling flow more accurately, a three dimensional melt flow model was established on a viscous, incompressible, and non-isothermal fluid, and a control volume-based finite volume method was employed to discretize the governing equations. A two-fold iterative method was proposed to decouple the dependence among pressure, velocity, and temperature so as to reduce the computation and improve the numerical stability. Based on the proposed theoretical model and numerical method, a program code was developed to simulate melt front progress and flow fields. The numerical simulations for different injection speeds, melt temperatures, and gate locations were carried out to explore the jetting mechanism. The results indicate the filling pattern depends on the competition between inertial and viscous forces. When inertial force exceeds the viscous force jetting occurs, then it changes to a buckling flow as the viscous force competes over the inertial force. Once the melt contacts with the mold wall, the melt filling switches to conventional sequential filling mode. Numerical results also indicate jetting length increases with injection speed but changes little with melt temperature. The reasonable agreements between simulated and experimental jetting length and buckling frequency imply the proposed method is valid for jetting simulation.