Vasily V. Koltashev
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Vasily V. Koltashev has a total of 36 co-authors. Here are the top co-authors by number of shared publications:
Alexander Velmuzhov
Devyatykh Institute of Chemistry of High-Purity Substances Russian Academy of Sciences Nizhny Novgorod Russia
2 shared publicationsAndrey Okhrimchuk
Prokhorov General Physics Institute Russian Academy of Sciences Dianov Fiber Optics Research Center Moscow Russia
2 shared publicationsBoris Denker
Prokhorov General Physics Institute Russian Academy of Sciences Moscow Russia
2 shared publicationsBoris Galagan
Prokhorov General Physics Institute Russian Academy of Sciences Moscow Russia
2 shared publicationsMaxim Sukhanov
Devyatykh Institute of Chemistry of High-Purity Substances Russian Academy of Sciences Nizhny Novgorod Russia
2 shared publicationsSergei Sverchkov
Prokhorov General Physics Institute Russian Academy of Sciences Moscow Russia
2 shared publications
Latest Publications
- 27 October 2024
- Published by Allerton Press in Physics of Wave Phenomena
- Vol. 32 (5) , 315-319
5-µm Lasing on Tb3+ Ions in a Chalcogenide Fiber Pumped by a 2.8-µm Er:ZBLAN Laser
Mid-IR lasing of a Tb3+-doped chalcogenide fiber has been demonstrated. Pumping was performed by a CW Er:ZBLAN laser, emitting at a wavelength of 2.795
- 27 October 2024
- Published by Allerton Press in Physics of Wave Phenomena
- Vol. 32 (5) , 315-319
5-µm Lasing on Tb3+ Ions in a Chalcogenide Fiber Pumped by a 2.8-µm Er:ZBLAN Laser
Mid-IR lasing of a Tb3+-doped chalcogenide fiber has been demonstrated. Pumping was performed by a CW Er:ZBLAN laser, emitting at a wavelength of 2.795
- Open Access
- 20 August 2024
- Published by Optica Publishing Group in Optica Open
Laser writing of Bragg grating in Tb3+ doped chalcogenide glass fiber for oscillations at 5 μm
A technique for direct laser writing of Bragg gratings in the fiber composed of high refractive index chalcogenide glass has been developed and verified. The fiber had a doped selenide glass core in an undoped sulfide glass cladding. The main features of the implemented inscription technique are solid immersion of the fiber and separate control of the focusing numerical apertures within planes perpendicular to the fiber and containing the fiber. A narrowband oscillation at 5 µm was obtained for the first time due to feedback by the Bragg grating.
- 20 August 2024
- Published by Optica Publishing Group in Optica Open
Open AccessLaser writing of Bragg grating in Tb3+ doped chalcogenide glass fiber for oscillations at 5 μm
A technique for direct laser writing of Bragg gratings in the fiber composed of high refractive index chalcogenide glass has been developed and verified. The fiber had a doped selenide glass core in an undoped sulfide glass cladding. The main features of the implemented inscription technique are solid immersion of the fiber and separate control of the focusing numerical apertures within planes perpendicular to the fiber and containing the fiber. A narrowband oscillation at 5 µm was obtained for the first time due to feedback by the Bragg grating.
- Open Access
- 20 August 2024
- Published by Optica Publishing Group in Optica Open
Laser writing of Bragg grating in Tb3+ doped chalcogenide glass fiber for oscillations at 5 μm
A technique for direct laser writing of Bragg gratings in the fiber composed of high refractive index chalcogenide glass has been developed and verified. The fiber had a doped selenide glass core in an undoped sulfide glass cladding. The main features of the implemented inscription technique are solid immersion of the fiber and separate control of the focusing numerical apertures within planes perpendicular to the fiber and containing the fiber. A narrowband oscillation at 5 µm was obtained for the first time due to feedback by the Bragg grating.
- 20 August 2024
- Published by Optica Publishing Group in Optica Open
Open AccessLaser writing of Bragg grating in Tb3+ doped chalcogenide glass fiber for oscillations at 5 μm
A technique for direct laser writing of Bragg gratings in the fiber composed of high refractive index chalcogenide glass has been developed and verified. The fiber had a doped selenide glass core in an undoped sulfide glass cladding. The main features of the implemented inscription technique are solid immersion of the fiber and separate control of the focusing numerical apertures within planes perpendicular to the fiber and containing the fiber. A narrowband oscillation at 5 µm was obtained for the first time due to feedback by the Bragg grating.
- Open Access
Rare-Earth-Doped Selenide Glasses as Laser Materials for the 5–6 μm Spectral Range
This paper provides an overview of mid-infrared lasers based on rare-earth-ion-doped selenide glasses. Laser action was demonstrated at the transitions between the first excited and the ground levels of Ce3+, Pr3+, Nd3+ and Tb3+ ions. The highest output parameters for bulk glass lasers (over 40 mJ of output energy) and wavelength tuning in the range of 4.6–5.6 microns were obtained with Ce3+-doped glass. The highest output parameters for fiber lasers (150 mW at 5.1–5.3 μm under continuous pumping) were demonstrated with Tb3+ ions. The longest lasing wavelengths for any glass laser and tunability within the 5.56–6.01 µm spectral band were shown with Nd3+ ions in a Tb3+-Nd3+ co-doped system.
Open AccessRare-Earth-Doped Selenide Glasses as Laser Materials for the 5–6 μm Spectral Range
This paper provides an overview of mid-infrared lasers based on rare-earth-ion-doped selenide glasses. Laser action was demonstrated at the transitions between the first excited and the ground levels of Ce3+, Pr3+, Nd3+ and Tb3+ ions. The highest output parameters for bulk glass lasers (over 40 mJ of output energy) and wavelength tuning in the range of 4.6–5.6 microns were obtained with Ce3+-doped glass. The highest output parameters for fiber lasers (150 mW at 5.1–5.3 μm under continuous pumping) were demonstrated with Tb3+ ions. The longest lasing wavelengths for any glass laser and tunability within the 5.56–6.01 µm spectral band were shown with Nd3+ ions in a Tb3+-Nd3+ co-doped system.
- Open Access
Thermal, Optical, and IR-Emission Properties of Extremely Low Hydroxyl TeO2-WO3-Bi2O3-La2O3-xEr2O3 Glasses for Mid-Infrared Photonics
A series of glass samples of the tungsten–tellurite system TeO2-WO3-Bi2O3-(4-x) La2O3-xEr2O3, x = 0; 0.4; 0.5; 0.7; 1.2; 2; 4 mol%, CEr = 0 - 15 × 1020 cm−3 were synthesized from high-purity oxides in an oxygen flow inside a specialized sealed reactor. In all samples of the series, an extremely low content of hydroxyl groups was achieved (~n × 1016 cm−3, more than 4 orders of magnitude lower than the concentration of erbium ions), which guarantees minimal effects on the luminescence properties of Er3+. The glasses are resistant to crystallization up to 4 mol% Er2O3, and the glass transition temperatures do not depend on the concentration of erbium oxide when introduced by replacing lanthanum oxide. Thin 0.2 mm plates have high transmittance at a level of 20% in the 4.7–5.3 µm range, and the absorption bands of hydroxyl groups at about 2.3, 3, and 4.4 µm, which are typical for ordinary tellurite glass samples, are indistinguishable. The introduction of erbium oxide led to an insignificant change in the refractive index. Er2O3-concentration dependences of the luminescence intensities and lifetimes near the wavelengths of 1.53 and 2.75 μm were found for the 4I13/2–4I15/2 and 4I11/2–4I13/2 /transitions of the Er3+ ion. The data obtained are necessary for the development of mid-infrared photonics; in particular, for the design of Er3+-doped fiber lasers.
Open AccessThermal, Optical, and IR-Emission Properties of Extremely Low Hydroxyl TeO2-WO3-Bi2O3-La2O3-xEr2O3 Glasses for Mid-Infrared Photonics
A series of glass samples of the tungsten–tellurite system TeO2-WO3-Bi2O3-(4-x) La2O3-xEr2O3, x = 0; 0.4; 0.5; 0.7; 1.2; 2; 4 mol%, CEr = 0 - 15 × 1020 cm−3 were synthesized from high-purity oxides in an oxygen flow inside a specialized sealed reactor. In all samples of the series, an extremely low content of hydroxyl groups was achieved (~n × 1016 cm−3, more than 4 orders of magnitude lower than the concentration of erbium ions), which guarantees minimal effects on the luminescence properties of Er3+. The glasses are resistant to crystallization up to 4 mol% Er2O3, and the glass transition temperatures do not depend on the concentration of erbium oxide when introduced by replacing lanthanum oxide. Thin 0.2 mm plates have high transmittance at a level of 20% in the 4.7–5.3 µm range, and the absorption bands of hydroxyl groups at about 2.3, 3, and 4.4 µm, which are typical for ordinary tellurite glass samples, are indistinguishable. The introduction of erbium oxide led to an insignificant change in the refractive index. Er2O3-concentration dependences of the luminescence intensities and lifetimes near the wavelengths of 1.53 and 2.75 μm were found for the 4I13/2–4I15/2 and 4I11/2–4I13/2 /transitions of the Er3+ ion. The data obtained are necessary for the development of mid-infrared photonics; in particular, for the design of Er3+-doped fiber lasers.
- 15 June 2020
- Published by Pleiades Publishing Ltd in Geochemistry International
- Vol. 58 (6) , 670-686
Influence of C–O–H Volatiles on Ni, Co, and P Partition between Silicate Melt and Liquid Metal Fe Alloy at 4 GPa, 1550°C
A set of experiments was carried out in the system NaAlSi3O8–FeO–NiO–CoO–SiC–NaH2PO4 at 1550°C, 4 GPa, and oxygen fugacity (fO2) 0.5–2.9 log. units below the iron–wüstite (IW) buffer to estimate how C–O–H components can affect Ni, Co, and P partition between silicate melt and a liquid metallic phase at redox conditions under which the metallic phase is segregated into melting products of the early reduced mantles of the Earth and other planetary bodies. It has been established that the Ni, Co, and P partition coefficients D(М)met/sil between silicate melts saturated with carbon and containing dissolved C–O–H volatiles (mainly in the form of OH groups, H2 and CH4) at relatively oxidized conditions (fO2 > IW – 1.5) correspond to D(М)met/sil values expected of metal–silicate melt equilibrium in volatile-free systems at analogous P, T, fO2, and nbo/t parameters. Under more reduced conditions (fO2 ≤ IW – 2), the presence of C–O–H volatiles leads to a decrease in D(М)met/sil for Ni and P compared to that in “dry” melts. This difference increases with decreasing fO2 and reaches ~0.5 and more than one order of magnitude for Ni and P, respectively, at fO2 = IW – 2.9. The effect of volatiles on D(Co)met/sil is much weaker, and hence, a decrease in fO2 leads to that D(Ni)met/sil and D(Co)met/sil converge. The Raman spectra of the experimental glasses and their SIMS analyses for hydrogen show that water content (OH + H2O) in the melts decreases with decreasing fO2, whereas the contents of CH4 and complexes with C–H bonds significantly increases. The likely reasons for the decrease in D(М)met/sil under strongly reduced conditions may be changes in the structure of the silicate melts and the origin of complex compounds of siderophile elements with volatiles in these melts.
- 15 June 2020
- Published by Pleiades Publishing Ltd in Geochemistry International
- Vol. 58 (6) , 670-686
Influence of C–O–H Volatiles on Ni, Co, and P Partition between Silicate Melt and Liquid Metal Fe Alloy at 4 GPa, 1550°C
A set of experiments was carried out in the system NaAlSi3O8–FeO–NiO–CoO–SiC–NaH2PO4 at 1550°C, 4 GPa, and oxygen fugacity (fO2) 0.5–2.9 log. units below the iron–wüstite (IW) buffer to estimate how C–O–H components can affect Ni, Co, and P partition between silicate melt and a liquid metallic phase at redox conditions under which the metallic phase is segregated into melting products of the early reduced mantles of the Earth and other planetary bodies. It has been established that the Ni, Co, and P partition coefficients D(М)met/sil between silicate melts saturated with carbon and containing dissolved C–O–H volatiles (mainly in the form of OH groups, H2 and CH4) at relatively oxidized conditions (fO2 > IW – 1.5) correspond to D(М)met/sil values expected of metal–silicate melt equilibrium in volatile-free systems at analogous P, T, fO2, and nbo/t parameters. Under more reduced conditions (fO2 ≤ IW – 2), the presence of C–O–H volatiles leads to a decrease in D(М)met/sil for Ni and P compared to that in “dry” melts. This difference increases with decreasing fO2 and reaches ~0.5 and more than one order of magnitude for Ni and P, respectively, at fO2 = IW – 2.9. The effect of volatiles on D(Co)met/sil is much weaker, and hence, a decrease in fO2 leads to that D(Ni)met/sil and D(Co)met/sil converge. The Raman spectra of the experimental glasses and their SIMS analyses for hydrogen show that water content (OH + H2O) in the melts decreases with decreasing fO2, whereas the contents of CH4 and complexes with C–H bonds significantly increases. The likely reasons for the decrease in D(М)met/sil under strongly reduced conditions may be changes in the structure of the silicate melts and the origin of complex compounds of siderophile elements with volatiles in these melts.
- 13 May 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Quantum Electronics
- Vol. 52 (7) , 1-12
Basic and Peculiar Properties of Chromium–Magnesium Co-Doped YAS-Based Optical Fibers
The basic and peculiar properties of new-type chromium (Cr) and magnesium (Mg) co-doped yttrio–alumino–silicate-based optical fibers, fabricated through the classic modified chemical vapor deposition method employed in conjunction with solution-doping technique, are addressed, with most of attention being paid to impact of Cr/Mg co-doping strength. The electron probe microanalysis, Raman, optical absorption, and fluorescence [at excitation at different wavelengths, spanning visible to near-infrared (NIR)] spectra’ measurements are performed for clarifying overall state-of-the-art of the fibers. Their most remarkable features are demonstrated to be pronounceable fluorescence in NIR (beyond 1 $\mu \text{m}$ ) and as well pronounceable bleaching effect under the action of 1- $\mu \text{m}$ light, both adherent to the presence of Cr 4+ ions.
- 13 May 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Quantum Electronics
- Vol. 52 (7) , 1-12
Basic and Peculiar Properties of Chromium–Magnesium Co-Doped YAS-Based Optical Fibers
The basic and peculiar properties of new-type chromium (Cr) and magnesium (Mg) co-doped yttrio–alumino–silicate-based optical fibers, fabricated through the classic modified chemical vapor deposition method employed in conjunction with solution-doping technique, are addressed, with most of attention being paid to impact of Cr/Mg co-doping strength. The electron probe microanalysis, Raman, optical absorption, and fluorescence [at excitation at different wavelengths, spanning visible to near-infrared (NIR)] spectra’ measurements are performed for clarifying overall state-of-the-art of the fibers. Their most remarkable features are demonstrated to be pronounceable fluorescence in NIR (beyond 1 $\mu \text{m}$ ) and as well pronounceable bleaching effect under the action of 1- $\mu \text{m}$ light, both adherent to the presence of Cr 4+ ions.