Yajun Xia
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Yajun Xia has a total of 10 co-authors. Here are the top co-authors by number of shared publications:
- Niansong Mei
Shanghai Advanced Research Institute, Chinese Academy of Sciences, Shanghai 201210, China
2 shared publications - Zhaofeng Zhang
Chinese Academy of Sciences
2 shared publications Chenhui Zhou
The School of Electronic and Information Engineering Fujian Polytechnic Normal University Fuzhou, P.R. China
1 shared publicationGuo-Hua Qiu
The School of Electronic and Information Engineering Fujian Polytechnic Normal University Fuzhou, P.R. China
1 shared publication- Lizhuang Liu
Shanghai Advanced Research Institute Chinese Academy of Sciences Shanghai China
1 shared publication - Peiqing Han
Shanghai Advanced Research Institute, Chinese Academy of Sciences, Shanghai 201210, China
1 shared publication
Latest Publications
- Open Access
- 13 April 2026
- Published by MDPI AG in Electronics
- Vol. 15 (8) , 1614
A Low-Power Low-IF BLE Receiver Front-End with a Common-Gate TIA and Gm-C Complex Filter for Body Area Network Applications
In this article, a low-power low-intermediate-frequency (Low-IF) receiver front-end is presented for Bluetooth Low Energy (BLE) body area network (BAN) applications. The receiver employs an input matching network, an inductorless self-biased inverter-based low-noise transconductance amplifier (LNTA), a single-balanced passive mixer, a common-gate transimpedance amplifier (TIA), and a Gm-C complex filter for image suppression. Native MOS devices are adopted to support low-voltage operation and reduce static power consumption. The interstage on-chip coupling capacitor between the RF front-end and the TIA is removed by aligning the DC operating points of the two stages. The receiver front-end is implemented in a 55 nm standard CMOS process and occupies an active area of 0.081 , excluding bonding pads. Post-layout simulations show that the proposed design achieves 45.2 dB gain, 7.2 dB noise figure, and 28.1 dB image rejection ratio over the 2.4–2.48 GHz band, while consuming 537 W. The proposed front-end is suitable for low-power BLE BAN sensor nodes.- 13 April 2026
- Published by MDPI AG in Electronics
- Vol. 15 (8) , 1614
Open AccessA Low-Power Low-IF BLE Receiver Front-End with a Common-Gate TIA and Gm-C Complex Filter for Body Area Network Applications
In this article, a low-power low-intermediate-frequency (Low-IF) receiver front-end is presented for Bluetooth Low Energy (BLE) body area network (BAN) applications. The receiver employs an input matching network, an inductorless self-biased inverter-based low-noise transconductance amplifier (LNTA), a single-balanced passive mixer, a common-gate transimpedance amplifier (TIA), and a Gm-C complex filter for image suppression. Native MOS devices are adopted to support low-voltage operation and reduce static power consumption. The interstage on-chip coupling capacitor between the RF front-end and the TIA is removed by aligning the DC operating points of the two stages. The receiver front-end is implemented in a 55 nm standard CMOS process and occupies an active area of 0.081 , excluding bonding pads. Post-layout simulations show that the proposed design achieves 45.2 dB gain, 7.2 dB noise figure, and 28.1 dB image rejection ratio over the 2.4–2.48 GHz band, while consuming 537 W. The proposed front-end is suitable for low-power BLE BAN sensor nodes. - 21 May 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-4
A Passive Noise-Shaping SAR ADC with Energy-Efficient Switching Method
In this paper, a low-voltage passive first-order noise shaping charge-redistribution successive approximation register (SAR) ADC with energy-efficient switching method is proposed. The energy -efficient switching method is achieved by one-side switching instead (OSSI) method and higher-bit switching instead (HBSI) method. The architecture is modified to realize the noise- shaping loop properly. We present a passive integrator with a dynamic DC offset to address the path gain error from the varying voltage on the capacitor array at each quantization step. Simulation results on a 180nm CMOS technology operated at 0.6V supply and 25kHz sampling rate show 130n W power consumption with a peak SNDR of 70.3dB..
- 21 May 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-4
A Passive Noise-Shaping SAR ADC with Energy-Efficient Switching Method
In this paper, a low-voltage passive first-order noise shaping charge-redistribution successive approximation register (SAR) ADC with energy-efficient switching method is proposed. The energy -efficient switching method is achieved by one-side switching instead (OSSI) method and higher-bit switching instead (HBSI) method. The architecture is modified to realize the noise- shaping loop properly. We present a passive integrator with a dynamic DC offset to address the path gain error from the varying voltage on the capacitor array at each quantization step. Simulation results on a 180nm CMOS technology operated at 0.6V supply and 25kHz sampling rate show 130n W power consumption with a peak SNDR of 70.3dB..
- Open Access
- 1 November 2020
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 1684 (1) , 012020
Research on the intelligent agricultural closed-loop system under the Internet of Things Architecture
—In this paper, a remote closed-loop agricultural monitoring system based on the Internet of things and artificial intelligence decision-making was presented. It introduces two innovations: 1. through the ZigBee wireless sensor networking module, the collected field environment information data is sent to the ARM main controller. This sensor data will be converted into complied with TCP/IP protocol data types in the main controller and send to the cloud server for storage and processing furtherly, thus can conveniently access the server to manage and know the growth status of flowers through multiple types of the smart terminal. A mixed ad-hoc network data perception system not only reduces the reliance on the electric wire but also improves system reliability and usage range. 2. smart compensated light technology used in this system can accelerate plant growth by using photosynthesis to match different red-blue light ratios that can achieve maximum growth points. The system in this paper realizes the remote monitoring and control and multi-mode management of flower plants.
- 1 November 2020
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 1684 (1) , 012020
Open AccessResearch on the intelligent agricultural closed-loop system under the Internet of Things Architecture
—In this paper, a remote closed-loop agricultural monitoring system based on the Internet of things and artificial intelligence decision-making was presented. It introduces two innovations: 1. through the ZigBee wireless sensor networking module, the collected field environment information data is sent to the ARM main controller. This sensor data will be converted into complied with TCP/IP protocol data types in the main controller and send to the cloud server for storage and processing furtherly, thus can conveniently access the server to manage and know the growth status of flowers through multiple types of the smart terminal. A mixed ad-hoc network data perception system not only reduces the reliance on the electric wire but also improves system reliability and usage range. 2. smart compensated light technology used in this system can accelerate plant growth by using photosynthesis to match different red-blue light ratios that can achieve maximum growth points. The system in this paper realizes the remote monitoring and control and multi-mode management of flower plants.
- Open Access
- 24 June 2020
- Published by MDPI AG in Electronics
- Vol. 9 (6) , 1042
A 920-MHz Dual-Mode Receiver with Energy Harvesting for UHF RFID Tag and IoT
A low-power dual-mode receiver is presented for ultra-high-frequency (UHF) radio frequency identification (RFID) systems. The reconfigurable architecture of the tag is proposed to be compatible with low-power and high-sensitivity operating modes. The read range of RFID system and the lifetime of the tag are increased by photovoltaic, thermoelectric and RF energy-harvesting topology. The receiver is implemented in a 0.18-μm standard CMOS process and occupies an active area of 0.65 mm × 0.7 mm. For low-power mode, the tag is powered by the rectifier and the sensitivity is −18 dBm. For high-sensitivity mode, the maximum PCE of the fully on-chip energy harvester is 46.5% with over 1-μW output power and the sensitivity is −40 dBm with 880 nW power consumption under the supply voltage of 0.8 V.
- 24 June 2020
- Published by MDPI AG in Electronics
- Vol. 9 (6) , 1042
Open AccessA 920-MHz Dual-Mode Receiver with Energy Harvesting for UHF RFID Tag and IoT
A low-power dual-mode receiver is presented for ultra-high-frequency (UHF) radio frequency identification (RFID) systems. The reconfigurable architecture of the tag is proposed to be compatible with low-power and high-sensitivity operating modes. The read range of RFID system and the lifetime of the tag are increased by photovoltaic, thermoelectric and RF energy-harvesting topology. The receiver is implemented in a 0.18-μm standard CMOS process and occupies an active area of 0.65 mm × 0.7 mm. For low-power mode, the tag is powered by the rectifier and the sensitivity is −18 dBm. For high-sensitivity mode, the maximum PCE of the fully on-chip energy harvester is 46.5% with over 1-μW output power and the sensitivity is −40 dBm with 880 nW power consumption under the supply voltage of 0.8 V.