Alexander Volnenko
Alexander Volnenko has a total of 15 co-authors. Here are the top co-authors by number of shared publications:
- Daulet Zhumadullayev
Department of Technological Machines and Equipment, M. Auezov South Kazakhstan University, Shymkent 160012, Kazakhstan
7 shared publications - Abay Akilbekovich Abzhapbarov
South Kazakhstan University named after M.Auezov, Shymkent, Kazakhstan
4 shared publications - Aliaksandr Eduardovich Leudanski
Belorussian State Technol Univ, Dept Proc & Apparat Chem Prod, Minsk, BELARUS
4 shared publications - Lazzat Ramatullayeva
М. Әуезов атындағы Оңтүстік Қазақстан университет
3 shared publications - Г.к. Ивахнюк3 shared publications
- М.к. Есенов3 shared publications
Latest Publications
- Open Access
- 1 July 2026
- Published by L. N. Gumilyov Eurasian National University in Eurasian Journal of Applied Engineering and Technology (EJAET)
- Vol. 155 (2) , 245-256
Расчет конструктивных параметров регулярной насадки тепломассообменного аппарата из непрерывно соединенных труб
Рассмотрены конструкции аппаратов с трубчатой насадкой регулярной структуры с внешним и внутренним расположением коллекторов и на основе анализа их работы нами создан аппарат с регулярной насадкой, выполненной в виде системы непрерывно и последовательно соединенных труб одного диаметра внутри корпуса аппарата. Основываясь на известном подходе движения газа по извилистым каналам, получены уравнения для расчета порозности трубчатой насадки из непрерывно соединенных труб в сечении аппарата, объемной порозности и эквивалентного диаметра, учитывающие конструктивные составляющие трубчатого пучка и шаги размещения труб в вертикальном и радиальном направлениях. Проведено сопоставление расчетных данных конструктивных параметров для трубчатых насадок с прямыми трубами и выносными коллекторами и непрерывно соединенных труб, которые показали, что присутствие отводов в пучке из непрерывно соединенных труб приводит к снижению численных значений объемной порозности и эквивалентного диаметра за счет уменьшения свободного пространства контактной зоны.
- 1 July 2026
- Published by L. N. Gumilyov Eurasian National University in Eurasian Journal of Applied Engineering and Technology (EJAET)
- Vol. 155 (2) , 245-256
Open AccessРасчет конструктивных параметров регулярной насадки тепломассообменного аппарата из непрерывно соединенных труб
Рассмотрены конструкции аппаратов с трубчатой насадкой регулярной структуры с внешним и внутренним расположением коллекторов и на основе анализа их работы нами создан аппарат с регулярной насадкой, выполненной в виде системы непрерывно и последовательно соединенных труб одного диаметра внутри корпуса аппарата. Основываясь на известном подходе движения газа по извилистым каналам, получены уравнения для расчета порозности трубчатой насадки из непрерывно соединенных труб в сечении аппарата, объемной порозности и эквивалентного диаметра, учитывающие конструктивные составляющие трубчатого пучка и шаги размещения труб в вертикальном и радиальном направлениях. Проведено сопоставление расчетных данных конструктивных параметров для трубчатых насадок с прямыми трубами и выносными коллекторами и непрерывно соединенных труб, которые показали, что присутствие отводов в пучке из непрерывно соединенных труб приводит к снижению численных значений объемной порозности и эквивалентного диаметра за счет уменьшения свободного пространства контактной зоны.
- Open Access
- 30 June 2026
- Published by D. Serikbayev East Kazakhstan Technical University in Central Asian Transactions on Materials Structure and Properties
- Vol. 2 (2) , 80-92
MODELING THE HEAT TRANSFER PROCESS IN A DEVICE WITH A TUBULAR PACKING OF CONTINUOUSLY CONNECTED PIPES
To conduct experimental studies and numerical experiments on the heat transfer process, based on the analysis of the design of devices with a tubular packing of a regular structure with external and internal arrangement of collectors, an apparatus with a regular packing made in the form of a system of continuously and sequentially connected pipes of the same diameter inside the device body was created. A simple zone scheme is proposed, which allows obtaining a system of linear equations for the temperaturesof the coolants in the selected zones of the device. The solution to the resulting system of equations satisfies the heat balances in the device. The distribution of the temperatures of the coolants along the device shows that the limiting stage of the heat exchange process is heat exchange from the gas side to the heat exchange surface. To eliminate this limiting stage, it is necessary that the area of the heat exchange surface on the gas side be greater than the area of heat exchange on the liquid side as many times as the heat transfer coefficient from the gas side hgis less than the heat transfer coefficient of the liquid coolant hlto the inner surface of the pipe.
- 30 June 2026
- Published by D. Serikbayev East Kazakhstan Technical University in Central Asian Transactions on Materials Structure and Properties
- Vol. 2 (2) , 80-92
Open AccessMODELING THE HEAT TRANSFER PROCESS IN A DEVICE WITH A TUBULAR PACKING OF CONTINUOUSLY CONNECTED PIPES
To conduct experimental studies and numerical experiments on the heat transfer process, based on the analysis of the design of devices with a tubular packing of a regular structure with external and internal arrangement of collectors, an apparatus with a regular packing made in the form of a system of continuously and sequentially connected pipes of the same diameter inside the device body was created. A simple zone scheme is proposed, which allows obtaining a system of linear equations for the temperaturesof the coolants in the selected zones of the device. The solution to the resulting system of equations satisfies the heat balances in the device. The distribution of the temperatures of the coolants along the device shows that the limiting stage of the heat exchange process is heat exchange from the gas side to the heat exchange surface. To eliminate this limiting stage, it is necessary that the area of the heat exchange surface on the gas side be greater than the area of heat exchange on the liquid side as many times as the heat transfer coefficient from the gas side hgis less than the heat transfer coefficient of the liquid coolant hlto the inner surface of the pipe.
- 1 October 2024
- Published by Interrin Scientific and Production Enterprise LLP in Горный журнал Казахстана
- No. 7(231),p. 46-50
Analysis of the impact of drum apparatus operating parameters on dust and pollutant emissions into the atmosphere
Бұл мақалада саптаманың екі түрінде де барабанды материалмен толтыру коэффициенті құрылғыдағы салқындатқыш жылдамдығының жоғарылауымен төмендейтіні анықталды. Тәуелділік диаграммалары жылдамдықтың жоғарылауымен кептіру материалының тығыздығына қарамастан толтыру коэффициенті төмендейтінін көрсетеді. Материалды жүктеуге қарай көлбеу барабанды орнатқан жағдайда, барабанның айналу жиілігі N жоғарылаған кезде толтыру коэффициенті жоғарылайтыны көрсетілген. Дәл осындай жағдайларда, бірақ барабанды төменге еңкейткенде, кері байланыс байқалады. Зерттеулерде материалдар мен әдістер қарастырылып, кептіру процесінің математикалық моделі жасалды. Эксперименттік нәтижелер бойынша, барабанды материалмен толтыру коэффициенті және материал бөлшектерінің болу уақыты барабанның көлбеу бұрышына, айналу жылдамдығына, салқындатқыштың жылдамдығына және саптама тиімділігіне байланысты анықталды In this paper, it was found that in both types of nozzles, the material fill factor of the drum decreases with increasing cooling rate in the device. The dependence diagrams show that as speed increases, the fill factor decreases, regardless of the density of the drying material. It is shown that in the case of installing an inclined drum, as the material is loaded, the filling coefficient increases when the drum rotation speed N increases. Under the same conditions, but when the drum is tilted towards the descent, feedback is observed. In the research, materials and methods were considered, and a mathematical model of the drying process was created. According to the experimental results, the drum filling coefficient with material and the residence time of material particles depend on the drum’s inclination angle, rotation speed, coolant speed, and nozzle efficiency В этой статье было обнаружено, что в обоих типах насадки коэффициент заполнения барабана материалом уменьшается с увеличением скорости охлаждения в устройстве. Диаграммы зависимости показывают, что с увеличением скорости коэффициент заполнения уменьшается независимо от плотности сушильного материала. Показано, что в случае установки наклонного барабана по мере загрузки материала коэффициент наполнения увеличивается, когда частота вращения барабана N увеличивается. В тех же условиях, но при наклоне барабана к спуску, наблюдается обратная связь. В исследованиях рассмотрены материалы и методы, создана математическая модель процесса сушки. По экспериментальным результатам было определено, что коэффициент заполнения барабана материалом и время нахождения частиц материала зависят от угла наклона барабана, скорости его вращения, скорости теплоносителя и эффективности насадки
- 1 October 2024
- Published by Interrin Scientific and Production Enterprise LLP in Горный журнал Казахстана
- No. 7(231),p. 46-50
Analysis of the impact of drum apparatus operating parameters on dust and pollutant emissions into the atmosphere
Бұл мақалада саптаманың екі түрінде де барабанды материалмен толтыру коэффициенті құрылғыдағы салқындатқыш жылдамдығының жоғарылауымен төмендейтіні анықталды. Тәуелділік диаграммалары жылдамдықтың жоғарылауымен кептіру материалының тығыздығына қарамастан толтыру коэффициенті төмендейтінін көрсетеді. Материалды жүктеуге қарай көлбеу барабанды орнатқан жағдайда, барабанның айналу жиілігі N жоғарылаған кезде толтыру коэффициенті жоғарылайтыны көрсетілген. Дәл осындай жағдайларда, бірақ барабанды төменге еңкейткенде, кері байланыс байқалады. Зерттеулерде материалдар мен әдістер қарастырылып, кептіру процесінің математикалық моделі жасалды. Эксперименттік нәтижелер бойынша, барабанды материалмен толтыру коэффициенті және материал бөлшектерінің болу уақыты барабанның көлбеу бұрышына, айналу жылдамдығына, салқындатқыштың жылдамдығына және саптама тиімділігіне байланысты анықталды In this paper, it was found that in both types of nozzles, the material fill factor of the drum decreases with increasing cooling rate in the device. The dependence diagrams show that as speed increases, the fill factor decreases, regardless of the density of the drying material. It is shown that in the case of installing an inclined drum, as the material is loaded, the filling coefficient increases when the drum rotation speed N increases. Under the same conditions, but when the drum is tilted towards the descent, feedback is observed. In the research, materials and methods were considered, and a mathematical model of the drying process was created. According to the experimental results, the drum filling coefficient with material and the residence time of material particles depend on the drum’s inclination angle, rotation speed, coolant speed, and nozzle efficiency В этой статье было обнаружено, что в обоих типах насадки коэффициент заполнения барабана материалом уменьшается с увеличением скорости охлаждения в устройстве. Диаграммы зависимости показывают, что с увеличением скорости коэффициент заполнения уменьшается независимо от плотности сушильного материала. Показано, что в случае установки наклонного барабана по мере загрузки материала коэффициент наполнения увеличивается, когда частота вращения барабана N увеличивается. В тех же условиях, но при наклоне барабана к спуску, наблюдается обратная связь. В исследованиях рассмотрены материалы и методы, создана математическая модель процесса сушки. По экспериментальным результатам было определено, что коэффициент заполнения барабана материалом и время нахождения частиц материала зависят от угла наклона барабана, скорости его вращения, скорости теплоносителя и эффективности насадки
- 30 September 2024
- Published by Dulaty University in Mechanics and Technologies
- No. 3,p. 276-286
ANALYSIS OF THE INFLUENCE OF DESIGN PARAMETERS ON ENERGY CONSUMPTION IN A HEAT AND MASS TRANSFER APPARATUS WITH A REGULAR ROTATING NOZZLE
The use of known designs of irregular and regular stationary nozzles, movable and regularly movable nozzles has been analyzed, their shortcomings have been identified and ways of their modernization have been established. An experimental study of the hydraulic resistance of a packed layer with rotating packed elements with rectangular blades was carried out when changing the location steps in the vertical and radial directions. It is noted that when changing the vertical step, it is possible to achieve an in-phase regime, characterized by an increase in the power of the formed vortices, which has a beneficial effect on achieving a highly developed interphase surface and the efficiency of the processes being carried out. The presence of a critical step is confirmed when the distances between adjacent packings in the same row in the radial direction change, at which a restructuring of the vortex formation mechanism occurs. The frequency of vortex formation before the critical step is determined by the size of the gap between adjacent packed elements in a row, and after it by the width of the streamlined elements. An equation has been obtained for calculating the hydraulic resistance of an apparatus with rotating packed elements with rectangular blades, which takes into account the processes of formation and interaction of vortices behind the packed elements and characterizes the energy consumption in the heat and mass transfer apparatus.
- 30 September 2024
- Published by Dulaty University in Mechanics and Technologies
- No. 3,p. 276-286
ANALYSIS OF THE INFLUENCE OF DESIGN PARAMETERS ON ENERGY CONSUMPTION IN A HEAT AND MASS TRANSFER APPARATUS WITH A REGULAR ROTATING NOZZLE
The use of known designs of irregular and regular stationary nozzles, movable and regularly movable nozzles has been analyzed, their shortcomings have been identified and ways of their modernization have been established. An experimental study of the hydraulic resistance of a packed layer with rotating packed elements with rectangular blades was carried out when changing the location steps in the vertical and radial directions. It is noted that when changing the vertical step, it is possible to achieve an in-phase regime, characterized by an increase in the power of the formed vortices, which has a beneficial effect on achieving a highly developed interphase surface and the efficiency of the processes being carried out. The presence of a critical step is confirmed when the distances between adjacent packings in the same row in the radial direction change, at which a restructuring of the vortex formation mechanism occurs. The frequency of vortex formation before the critical step is determined by the size of the gap between adjacent packed elements in a row, and after it by the width of the streamlined elements. An equation has been obtained for calculating the hydraulic resistance of an apparatus with rotating packed elements with rectangular blades, which takes into account the processes of formation and interaction of vortices behind the packed elements and characterizes the energy consumption in the heat and mass transfer apparatus.
- 26 September 2024
- Published by Interrin Scientific and Production Enterprise LLP in Горный журнал Казахстана
- No. 6(230),p. 34-41
Studying the influence of coolant speed on the processes of heat and mass transfer in technological equipment for processing disperse materials
W салқындатқыш ағынының жылдамдығы 1-4 м/с-қа дейін өскен кезде барабанның көлденең орналасуы кезінде барабанды материалмен толтыру коэффициентінің мәні 8,11%, ал барабанның көлбеу бұрышында α = 1° 5,68% төмендейтіні дәлелденді. Бұл газдың құлаған бөлшектерге әсер ету күшінің артуымен түсіндіріледі және олар перифериялық араластырғыш құрылғының қалақтарынан құлаған кезде түсіру жағына қарай үлкен қашықтыққа түсіріледі, бұл олардың кептіргіште болу уақытын τ азайтады және материалдың жылу тасымалдағышпен жанасу уақытын және температураны θ2 төмендетуге әкеледі: 2 °С (α = 0°); 1,7 °С(α = 1°). Кептіргіштен шығатын t2 кептіру агентінің температурасы сәйкесінше 5-6 °С артады. Бұл дайын өнімнің ылғалдылығының сәйкесінше өсуіне әкеледі: 2,2% (α = 0°), 3,09% (α = 1°). Мысалы, t1 80°С жоғарылаған кезде, Θ2 материалының температурасы артады: 8,5 °С (α = 0°), 3,5 °С (α = 2°). Барабанда кептіру агентінің массалық жылдамдығының артуы (wρг) 1,8-2,8 кг/(м2с) аралығында толтыру коэффициентінің 18-20% төмендеуіне әкеледі It has been proven that with an increase in coolant flow rate w in the range from 1-4m/s with a horizontal drum position, the value of the drum filling coefficient with material ψ decreases by 8.11%, and with the drum inclination angle α = 1° by 5.68% . This is explained by the fact that the force of the gas on falling particles increases and, when falling from the blades of the peripheral mixing device, they are carried a greater distance towards unloading, which reduces the time τ of their stay in the dryer and leads to a decrease in the time of contact of the material with the coolant and temperature θ2 by 2 °С (α = 0°); 1,7 °С (α = 1°). The temperature of the drying agent t2 leaving the dryer increases by 5-6 °C. In soybeans, this leads to an increase in the moisture content of the finished product by 2,2% (α = 0°), 3,09% (α = 1°). Thus, with an increase in t1 by 80 °C, the temperature of the material Θ2 increases by 8,5 °С (α = 0°), 3,5 °С (α = 2°). It was revealed that an increase in the mass velocity of the drying agent in the drum (wρг) 1.8-2.8 kg/(m2s) entails a decrease in the filling factor by 18-20% Доказано, что при возрастании скорости потока теплоносителя w = 1-4 м/с при горизонтальном расположении барабана значение коэффициента заполнения барабана материалом ψ уменьшается на 8,11%, а при угле наклона барабана α = 1° – на 5,68%. Здесь увеличивается сила воздействия газа на падающие частицы и они при падении с лопаток перемешивающего устройства сносятся на большее расстояние в сторону разгрузки, что снижает время τ их пребывания в сушилке и приводит к снижению времени контакта материала с теплоносителем и температуры θ2 на 2°С (α = 0°); 1,7 °С (α = 1°). Температура сушильного агента t2, выходящего из сушилки, увеличивается на 5-6 °С; ведет к возрастанию влажности готового продукта на 2,2% (α = 0°), 3,09% (α = 1°). При повышении t1 на 80 °С температура материала Θ2 увеличивается на 8,5 °С (α = 0°), 3,5 °С (α = 2°). Увеличение массовой скорости агента сушки в барабане (wρг) 1,8-2,8 кг/(м2с) влечет за собой понижение коэффициента заполнения на 18-20%
- 26 September 2024
- Published by Interrin Scientific and Production Enterprise LLP in Горный журнал Казахстана
- No. 6(230),p. 34-41
Studying the influence of coolant speed on the processes of heat and mass transfer in technological equipment for processing disperse materials
W салқындатқыш ағынының жылдамдығы 1-4 м/с-қа дейін өскен кезде барабанның көлденең орналасуы кезінде барабанды материалмен толтыру коэффициентінің мәні 8,11%, ал барабанның көлбеу бұрышында α = 1° 5,68% төмендейтіні дәлелденді. Бұл газдың құлаған бөлшектерге әсер ету күшінің артуымен түсіндіріледі және олар перифериялық араластырғыш құрылғының қалақтарынан құлаған кезде түсіру жағына қарай үлкен қашықтыққа түсіріледі, бұл олардың кептіргіште болу уақытын τ азайтады және материалдың жылу тасымалдағышпен жанасу уақытын және температураны θ2 төмендетуге әкеледі: 2 °С (α = 0°); 1,7 °С(α = 1°). Кептіргіштен шығатын t2 кептіру агентінің температурасы сәйкесінше 5-6 °С артады. Бұл дайын өнімнің ылғалдылығының сәйкесінше өсуіне әкеледі: 2,2% (α = 0°), 3,09% (α = 1°). Мысалы, t1 80°С жоғарылаған кезде, Θ2 материалының температурасы артады: 8,5 °С (α = 0°), 3,5 °С (α = 2°). Барабанда кептіру агентінің массалық жылдамдығының артуы (wρг) 1,8-2,8 кг/(м2с) аралығында толтыру коэффициентінің 18-20% төмендеуіне әкеледі It has been proven that with an increase in coolant flow rate w in the range from 1-4m/s with a horizontal drum position, the value of the drum filling coefficient with material ψ decreases by 8.11%, and with the drum inclination angle α = 1° by 5.68% . This is explained by the fact that the force of the gas on falling particles increases and, when falling from the blades of the peripheral mixing device, they are carried a greater distance towards unloading, which reduces the time τ of their stay in the dryer and leads to a decrease in the time of contact of the material with the coolant and temperature θ2 by 2 °С (α = 0°); 1,7 °С (α = 1°). The temperature of the drying agent t2 leaving the dryer increases by 5-6 °C. In soybeans, this leads to an increase in the moisture content of the finished product by 2,2% (α = 0°), 3,09% (α = 1°). Thus, with an increase in t1 by 80 °C, the temperature of the material Θ2 increases by 8,5 °С (α = 0°), 3,5 °С (α = 2°). It was revealed that an increase in the mass velocity of the drying agent in the drum (wρг) 1.8-2.8 kg/(m2s) entails a decrease in the filling factor by 18-20% Доказано, что при возрастании скорости потока теплоносителя w = 1-4 м/с при горизонтальном расположении барабана значение коэффициента заполнения барабана материалом ψ уменьшается на 8,11%, а при угле наклона барабана α = 1° – на 5,68%. Здесь увеличивается сила воздействия газа на падающие частицы и они при падении с лопаток перемешивающего устройства сносятся на большее расстояние в сторону разгрузки, что снижает время τ их пребывания в сушилке и приводит к снижению времени контакта материала с теплоносителем и температуры θ2 на 2°С (α = 0°); 1,7 °С (α = 1°). Температура сушильного агента t2, выходящего из сушилки, увеличивается на 5-6 °С; ведет к возрастанию влажности готового продукта на 2,2% (α = 0°), 3,09% (α = 1°). При повышении t1 на 80 °С температура материала Θ2 увеличивается на 8,5 °С (α = 0°), 3,5 °С (α = 2°). Увеличение массовой скорости агента сушки в барабане (wρг) 1,8-2,8 кг/(м2с) влечет за собой понижение коэффициента заполнения на 18-20%
- 18 July 2024
- Published by Interrin Scientific and Production Enterprise LLP in Горный журнал Казахстана
- No. 4(228),p. 50-58
Optimizing the capture of aerosol particles to protect the environment
Бұл мақалада газ-дисперсті қатты материалдар жүйесінде процестерді жүргізу үшін агрегаттарды экологиялық жаңғырту мәселелері ашылады және барабанды кептіру агрегатындағы аэрозоль ағынын бөлудің ғылыми негіздері қарастырылады. Тегіс және цилиндр тәрізді арналарда аэрозоль ағыны бөлшектерінің турбулентті-инерциялық тұндыруын бағалау көрсетілген. Тегіс және цилиндрлік беттерде аэрозоль ағынының динамикалық жылдамдығы анықталды. Аэрозоль ағынын бөлу тиімділігін бағалаудың энергетикалық тәсілі қарастырылды. Барабанды кептіргіште аэрозоль ағынының бөлшектерін бөлу тиімділігін бағалау ұсынылған. Келтірілген зерттеулер кептіру агрегаттарының жұмысын оңтайландыруға және олардың өнімділігін арттыруға арналған жаңа тәсілдер мен әдістерді ұсынады. Олар газдисперсиялы қатты материалдарды өңдеу технологияларын әрі қарай дамытуға қажетті маңызды деректерді ұсынады, бұл қоршаған ортаға теріс әсерді азайтуға ықпал етеді This article reveals the problems of environmental modernization of aggregates for conducting processes in a system of gas – dispersed solid materials and considers the scientific basis for the separation of aerosol flow in a drum drying aggregate. Evaluation of turbulent-inertial deposition of aerosol flow particles in smooth and cylindrical channels is shown. On smooth and cylindrical surfaces, the dynamic speed of the aerosol flow is determined. An energy approach to assessing the efficiency of aerosol flow distribution was considered. It is proposed to evaluate the efficiency of separation of Aerosol Jet particles in a drum dryer. The cited studies suggest new approaches and methods for optimizing the operation of drying aggregates and increasing their productivity. They provide important data necessary for the further development of technologies for processing gasdispersed solid materials, which will contribute to reducing the negative impact on the environment В данной статье раскрываются вопросы экологической модернизации агрегатов для проведения процессов в системе газодисперсных твердых материалов и рассматриваются научные основы распределения аэрозольного потока в барабанном сушильном агрегате. Показана оценка турбулентно-инерционного осаждения частиц аэрозольного потока в гладких и цилиндрических каналах. Определена динамическая скорость потока аэрозоля на гладких и цилиндрических поверхностях. Рассмотрен энергетический подход к оценке эффективности распределения аэрозольного потока. Предложена оценка эффективности разделения частиц аэрозольного потока в барабанной сушилке. Приведенные исследования предлагают новые подходы и методы оптимизации работы сушильных агрегатов и повышения их производительности. Они предоставляют важные данные, необходимые для дальнейшего развития технологий переработки твердых газодисперсных материалов, что способствует снижению негативного воздействия на окружающую среду
- 18 July 2024
- Published by Interrin Scientific and Production Enterprise LLP in Горный журнал Казахстана
- No. 4(228),p. 50-58
Optimizing the capture of aerosol particles to protect the environment
Бұл мақалада газ-дисперсті қатты материалдар жүйесінде процестерді жүргізу үшін агрегаттарды экологиялық жаңғырту мәселелері ашылады және барабанды кептіру агрегатындағы аэрозоль ағынын бөлудің ғылыми негіздері қарастырылады. Тегіс және цилиндр тәрізді арналарда аэрозоль ағыны бөлшектерінің турбулентті-инерциялық тұндыруын бағалау көрсетілген. Тегіс және цилиндрлік беттерде аэрозоль ағынының динамикалық жылдамдығы анықталды. Аэрозоль ағынын бөлу тиімділігін бағалаудың энергетикалық тәсілі қарастырылды. Барабанды кептіргіште аэрозоль ағынының бөлшектерін бөлу тиімділігін бағалау ұсынылған. Келтірілген зерттеулер кептіру агрегаттарының жұмысын оңтайландыруға және олардың өнімділігін арттыруға арналған жаңа тәсілдер мен әдістерді ұсынады. Олар газдисперсиялы қатты материалдарды өңдеу технологияларын әрі қарай дамытуға қажетті маңызды деректерді ұсынады, бұл қоршаған ортаға теріс әсерді азайтуға ықпал етеді This article reveals the problems of environmental modernization of aggregates for conducting processes in a system of gas – dispersed solid materials and considers the scientific basis for the separation of aerosol flow in a drum drying aggregate. Evaluation of turbulent-inertial deposition of aerosol flow particles in smooth and cylindrical channels is shown. On smooth and cylindrical surfaces, the dynamic speed of the aerosol flow is determined. An energy approach to assessing the efficiency of aerosol flow distribution was considered. It is proposed to evaluate the efficiency of separation of Aerosol Jet particles in a drum dryer. The cited studies suggest new approaches and methods for optimizing the operation of drying aggregates and increasing their productivity. They provide important data necessary for the further development of technologies for processing gasdispersed solid materials, which will contribute to reducing the negative impact on the environment В данной статье раскрываются вопросы экологической модернизации агрегатов для проведения процессов в системе газодисперсных твердых материалов и рассматриваются научные основы распределения аэрозольного потока в барабанном сушильном агрегате. Показана оценка турбулентно-инерционного осаждения частиц аэрозольного потока в гладких и цилиндрических каналах. Определена динамическая скорость потока аэрозоля на гладких и цилиндрических поверхностях. Рассмотрен энергетический подход к оценке эффективности распределения аэрозольного потока. Предложена оценка эффективности разделения частиц аэрозольного потока в барабанной сушилке. Приведенные исследования предлагают новые подходы и методы оптимизации работы сушильных агрегатов и повышения их производительности. Они предоставляют важные данные, необходимые для дальнейшего развития технологий переработки твердых газодисперсных материалов, что способствует снижению негативного воздействия на окружающую среду
- 30 June 2024
- Published by Dulaty University in Mechanics and Technologies
- No. 2,p. 289-298
CALCULATION OF POROSITY AND EQUIVALENT NOZZLE DIAMETER OF A HEAT AND MASS TRANSFER APPARATUS WITH A REGULAR ROTATING NOZZLE
The use of modernized irregular stationary nozzles, regular stationary nozzles, movable (suspended, gushing and circulating) and regular movable nozzles in heat and mass transfer devices is considered. It is established that the gas movement is carried out along tortuous channels formed by regularly placed nozzle elements. Equations for calculating the porosity of the rotating nozzle in the cross-section of the apparatus, volume porosity and equivalent diameter, taking into account the structural components of rotating nozzle elements with rectangular blades and the steps of placing the nozzle elements in the vertical and radial directions, have been obtained. The influence of arrangement steps of the nozzle elements on the equivalent diameter on the basis of the obtained graphical dependences is considered and analysed. It is determined that the equivalent diameter depends on the steps of rotating elements arrangement in vertical and radial directions in direct proportion. It allows to assume that at average values of steps of arrangement of the nozzle elements it is possible to reduce energy consumption.
- 30 June 2024
- Published by Dulaty University in Mechanics and Technologies
- No. 2,p. 289-298
CALCULATION OF POROSITY AND EQUIVALENT NOZZLE DIAMETER OF A HEAT AND MASS TRANSFER APPARATUS WITH A REGULAR ROTATING NOZZLE
The use of modernized irregular stationary nozzles, regular stationary nozzles, movable (suspended, gushing and circulating) and regular movable nozzles in heat and mass transfer devices is considered. It is established that the gas movement is carried out along tortuous channels formed by regularly placed nozzle elements. Equations for calculating the porosity of the rotating nozzle in the cross-section of the apparatus, volume porosity and equivalent diameter, taking into account the structural components of rotating nozzle elements with rectangular blades and the steps of placing the nozzle elements in the vertical and radial directions, have been obtained. The influence of arrangement steps of the nozzle elements on the equivalent diameter on the basis of the obtained graphical dependences is considered and analysed. It is determined that the equivalent diameter depends on the steps of rotating elements arrangement in vertical and radial directions in direct proportion. It allows to assume that at average values of steps of arrangement of the nozzle elements it is possible to reduce energy consumption.
- Open Access
- 26 February 2021
- Published by Private Company Technology Center in Technology audit and production reserves
- Vol. 1 (3(57)) , 21-25
Study of dust collection effectiveness in cyclonic-vortex action apparatus
The object of research is the efficiency of dust collection of fine dust in an apparatus with an intense turbulent mode of phase interaction. One of the most problematic areas of the existing dust and gas cleaning equipment is the low efficiency of collecting fine dust. Effective cleaning of exhaust gases from dust involves the use of multi-stage cleaning systems, including wet and dry dust cleaning devices, which entails high capital and operating costs. These disadvantages are eliminated in the developed design of the cyclone-vortex dust collector with two contact zones. The device implements both dry and wet dust collection mechanisms, which allows for high efficiency of dust removal at high productivity. The conducted studies of the total and fractional efficiency of dust collection when changing the operating parameters of the developed device showed that the efficiency of collecting fine dust is 98–99 %. The increase in the efficiency of dust collection in the dry stage of the device is due to an increase in centrifugal force. In the wet stage of contact, the efficiency reaches its maximum values due to the vortex crushing of the liquid in the nozzle zone of the apparatus. Studies of the fractional efficiency of the apparatus show that with an increase in the diameter of the captured particles, the efficiency of the dust collection process for dry and wet stages, as well as the overall efficiency, increases. With an increase in the density of irrigation, the overall efficiency of dust collection in the apparatus increases. It has been established that an increase in the efficiency of capturing highly dispersed particles occurs due to turbulent diffusion, the value of which is determined by the frequency of turbulent pulsations and the degree of entrainment of particles during the pulsating motion of packed bodies. To describe the results obtained, a centrifugal-inertial model for a dry contact stage and a turbulent-diffusion model of solid particle deposition for a wet contact stage are proposed, which make it possible to calculate the dust collection efficiency of the contact stages, as well as the overall efficiency of the cyclone-vortex apparatus. The results obtained show the prospects of using devices of this design at heat power plants and other industries.
- 26 February 2021
- Published by Private Company Technology Center in Technology audit and production reserves
- Vol. 1 (3(57)) , 21-25
Open AccessStudy of dust collection effectiveness in cyclonic-vortex action apparatus
The object of research is the efficiency of dust collection of fine dust in an apparatus with an intense turbulent mode of phase interaction. One of the most problematic areas of the existing dust and gas cleaning equipment is the low efficiency of collecting fine dust. Effective cleaning of exhaust gases from dust involves the use of multi-stage cleaning systems, including wet and dry dust cleaning devices, which entails high capital and operating costs. These disadvantages are eliminated in the developed design of the cyclone-vortex dust collector with two contact zones. The device implements both dry and wet dust collection mechanisms, which allows for high efficiency of dust removal at high productivity. The conducted studies of the total and fractional efficiency of dust collection when changing the operating parameters of the developed device showed that the efficiency of collecting fine dust is 98–99 %. The increase in the efficiency of dust collection in the dry stage of the device is due to an increase in centrifugal force. In the wet stage of contact, the efficiency reaches its maximum values due to the vortex crushing of the liquid in the nozzle zone of the apparatus. Studies of the fractional efficiency of the apparatus show that with an increase in the diameter of the captured particles, the efficiency of the dust collection process for dry and wet stages, as well as the overall efficiency, increases. With an increase in the density of irrigation, the overall efficiency of dust collection in the apparatus increases. It has been established that an increase in the efficiency of capturing highly dispersed particles occurs due to turbulent diffusion, the value of which is determined by the frequency of turbulent pulsations and the degree of entrainment of particles during the pulsating motion of packed bodies. To describe the results obtained, a centrifugal-inertial model for a dry contact stage and a turbulent-diffusion model of solid particle deposition for a wet contact stage are proposed, which make it possible to calculate the dust collection efficiency of the contact stages, as well as the overall efficiency of the cyclone-vortex apparatus. The results obtained show the prospects of using devices of this design at heat power plants and other industries.
- 1 November 2020
- Published by National Academy of Sciences of the Republic of Kazakshtan in Series of Geology and Technical Sciences
- Vol. 6 (6) , 50-58
POLYMER WASTES' FLOTATION SEPARATION RESEARCH RESULTS
For separation of plastic wastes (polyamide (PA), acrylonitrile butadiene styrene (ABS) and polystyrene (PS), a flotation method is proposed. Using this method, the effect of concentration of surface-active substances (surfactants), which were used as polidocanol, sulphanole and a mixture of surfactants containing sodium laureth sulfate and diethanolamide, was studied. The research results analysis of the flotation separation of a mixture of crushed plastic wastes was carried out according to the calculated values of the extraction of a floated component c and the purity of a concentrate beta. It was noted that the maximum extraction of the floated component depends on the polymer and surfactant type. A mixture of surfactants at lower concentrations allows to achieve greater extraction of the floated component with less foaming ability. The research results on the extraction of polystyrene from the air flow rate at various concentrations of surfactants' mixture show that the extraction has a maximum at a certain air flow rate. At low air flow rates, the working volume of liquid is not saturated enough with gas bubbles. If the optimal value of air flow rates is exceeded, many gas bubbles are formed that are not involved in the flotation process. The research results on the extraction of polystyrene from the aerated liquid layer height at various concentrations of surfactants' mixture show that, at a low height of the aerated liquid layer, the probability of collision of a plastic particle with an air bubble is low and some potentially floated particles seek the bottom of an apparatus without having time to collide with an air bubble. When assessing the influence of liquid temperature on the flotation process, it was found that increasing the liquid temperature above 20 degrees C leads to a sharp decrease in ABS and PS extraction. This is explained by the fact that the dependence of the surfactants' foaming ability on the temperature is characterized by solubility curves and for most surfactants they have an extremum.
- 1 November 2020
- Published by National Academy of Sciences of the Republic of Kazakshtan in Series of Geology and Technical Sciences
- Vol. 6 (6) , 50-58
POLYMER WASTES' FLOTATION SEPARATION RESEARCH RESULTS
For separation of plastic wastes (polyamide (PA), acrylonitrile butadiene styrene (ABS) and polystyrene (PS), a flotation method is proposed. Using this method, the effect of concentration of surface-active substances (surfactants), which were used as polidocanol, sulphanole and a mixture of surfactants containing sodium laureth sulfate and diethanolamide, was studied. The research results analysis of the flotation separation of a mixture of crushed plastic wastes was carried out according to the calculated values of the extraction of a floated component c and the purity of a concentrate beta. It was noted that the maximum extraction of the floated component depends on the polymer and surfactant type. A mixture of surfactants at lower concentrations allows to achieve greater extraction of the floated component with less foaming ability. The research results on the extraction of polystyrene from the air flow rate at various concentrations of surfactants' mixture show that the extraction has a maximum at a certain air flow rate. At low air flow rates, the working volume of liquid is not saturated enough with gas bubbles. If the optimal value of air flow rates is exceeded, many gas bubbles are formed that are not involved in the flotation process. The research results on the extraction of polystyrene from the aerated liquid layer height at various concentrations of surfactants' mixture show that, at a low height of the aerated liquid layer, the probability of collision of a plastic particle with an air bubble is low and some potentially floated particles seek the bottom of an apparatus without having time to collide with an air bubble. When assessing the influence of liquid temperature on the flotation process, it was found that increasing the liquid temperature above 20 degrees C leads to a sharp decrease in ABS and PS extraction. This is explained by the fact that the dependence of the surfactants' foaming ability on the temperature is characterized by solubility curves and for most surfactants they have an extremum.
- Open Access
- 15 June 2020
- Published by National Academy of Sciences of the Republic of Kazakshtan in SERIES CHEMISTRY AND TECHNOLOGY
- Vol. 3 (441) , 36-43
STUDY OF THE EFFECT OF AIR CONSUMPTION, LIQUID LAYER HEIGHT AND TEMPERATURE ON THE PROCESS OF FLOTATION SEPARATION OF GROUND PLASTICS
- 15 June 2020
- Published by National Academy of Sciences of the Republic of Kazakshtan in SERIES CHEMISTRY AND TECHNOLOGY
- Vol. 3 (441) , 36-43
Open AccessSTUDY OF THE EFFECT OF AIR CONSUMPTION, LIQUID LAYER HEIGHT AND TEMPERATURE ON THE PROCESS OF FLOTATION SEPARATION OF GROUND PLASTICS