NKNusret Kaya

Nusret Kaya

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Nusret Kaya has a total of 33 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Metal–Ceramic AlSiC Hybrid Fillers for Polypropylene Composites: Thermal–Electrical Transport Decoupling for Thermal Interface Applications

    by Nusret Kaya

    Hybrid metal–ceramic fillers offer an effective strategy to overcome the intrinsic trade‐off between thermal conductivity and electrical insulation in polymer composites. Here, aluminum–silicon carbide (Al/SiC) hybrid particles were incorporated into a polypropylene (PP) matrix to achieve thermally conductive yet electrically insulating composites. The hybrid fillers were prepared by ball milling and melt compounded into PP at loadings up to 60 wt%. Thermal, electrical, mechanical, viscoelastic, and morphological properties were systematically characterized. Thermal conductivity increased monotonically with filler content, reaching a threefold enhancement ( k / k PP ≈3.04) at high loading, while electrical insulation was maintained up to 50 wt% without electrically percolated networks. Effective medium theory and percolation‐based modeling revealed a transition from isolated dispersion to thermally connected pathways dominated by phonon transport. Dynamic mechanical analysis showed a significant increase in storage modulus and a pronounced reduction in tan δ above 30 wt%, indicating suppressed viscous dissipation. This behavior is attributed to reduced interfacial damping enabled by the hybrid architecture, where aluminum particles act as localized mechanical and thermal bridges between adjacent SiC particles, enhancing stress transfer while limiting interfacial sliding and phonon scattering. These results demonstrate a viable interfacial engineering strategy for advanced thermal management applications.

  • Synergetic effects in hybrid hexagonal boron nitride/high thermal conductive graphite reinforced polypropylene composites for advanced thermal applications

    by Nusret Kaya, Merve Karaman

    Effective thermal management has become crucial for the performance and reliability of miniaturized electronic devices. While high filler loading improves heat dissipation, it often compromises other essential properties. Therefore, hybrid fillers combining distinct functionalities offer promising alternatives. In this study, we investigated the mechanical, electrical, and thermal properties of polypropylene (PP) composites reinforced with a novel hybrid filler consisting of hexagonal boron nitride ( h BN) and high conductive graphite (Gr). The influence of filler ratios and the use of maleic anhydride grafted polypropylene (MaPP) as a compatibilizer are systematically explored. The results showed that the addition of h BN enhanced both tensile and flexural modulus as well as the thermal stability. The addition of 10 wt% h BN and 20 wt% graphite, along with 3 wt% MaPP, enhanced the tensile modulus of polypropylene composites from 2000 MPa to 2475 MPa and increased thermal conductivity from 0.32 W/m·K to 0.51 W/m·K. Additionally, while graphite reduced surface electrical resistivity from ∼10 15 to ∼10 8 Ω/sq, MaPP moderately mitigated this effect by disrupting conductive pathways.


  • Synergistic Effects of Aluminum Nitride and Super Thermal Conductive Graphite in Polypropylene‐Based Hybrid Composites: Structural, Mechanical, and Thermal Insights

    by Nusret Kaya, Merve Karaman

    In this study, hybrid polymer composites based on polypropylene (PP) are developed using aluminum nitride (AlN) and super thermal conductive graphite (Gr) as fillers to improve mechanical, structural, thermal, and electrical properties. A series of composites containing varying ratios of AlN and Gr are fabricated via melt mixing and hot‐press molding techniques. The synergistic effects of ceramic and carbon‐based fillers are systematically investigated through mechanical testing, SEM analysis, DSC/TGA thermal characterization, and electrical resistivity measurements. Results show that low filler concentrations led to improved dispersion, mechanical integrity, and enhanced thermal properties. The Gr addition act as an efficient nucleating agent and significantly increases crystallinity and thermal conductivity, while AlN contributes to mechanical reinforcement. In comparison with neat PP, the 10A20G composite exhibits ≈63% (≈1.6‐fold) higher thermal conductivity and about 10 4 times lower electrical resistivity, confirming its suitability for thermal interface applications. The findings suggest that the hybrid use of AlN and Gr can lead to high‐performance PP‐based composites for electronic packaging and thermal management applications.


  • Enhanced Gamma Radiation Shielding of Polyester Composites Reinforced With the Recycled Tungsten Oxide and Their Structural, Thermal Characteristics

    by Nusret Kaya, Merve Karaman, Mehmet Yeşil, Alif Ngimbi Diambu, Cenk Külçe

    While precise data are lacking, it is estimated that thousands of tons of tungsten waste are generated globally each year, highlighting the need for efficient utilization and recycling. Recycling tungsten lowers costs, reduces energy consumption, and minimizes environmental impact compared to primary mining. Using recycled tungsten carbide waste in gamma radiation shielding materials offers both environmental and economic advantages. This study investigates the gamma‐ray shielding performance of recycled tungsten oxide/polyester (WO‐PEs) composites, focusing on the impact of tungsten oxide content on structural and shielding characteristics. XRD results showed that higher tungsten oxide content enhanced the crystallinity of the polyester matrix. FTIR and Raman spectra confirmed successful integration of tungsten oxide into the composite structure. Gamma‐ray shielding performance was evaluated at 662 keV by measuring the linear attenuation coefficient (LAC), mass attenuation coefficient (MAC), and half‐value layer. The highest attenuation was achieved with the composite containing 50% tungsten oxide. Comparisons with conventional materials demonstrated the potential of WO‐PEs as an effective and economical shielding alternative. Theoretical LAC and MAC values calculated with XCOM software supported experimental results, although slight discrepancies appeared at higher gamma‐ray energies.


  • Photocatalytic performance and characterization of tungsten oxide powders recycled from cutting tool wastes

    by Nusret Kaya, Ahmet Yavaş, Mücahit Sütçü, Merve Karaman

    In this study, with recycling process from waste sludge formed by the wear of WC cutting tools used as a cutting tool in the machining industry has been presented. WC waste transformed to WO 3− x have been characterized by the X‐ray diffraction, and scanning electron microscopy–EDS analysis. The formation of WO 3− x from the waste WC bulk materials was further confirmed by Fourier transform infrared spectroscopy and Raman spectroscopy. To understand its photocatalytic performance, the photophysical properties of the material were investigated with UV–vis. The photocatalytic degradation of organic impurities in the water from a recycled material was carried out. According to the results, the best photodegradation efficiency was obtained with the 0.4 × 10 −5  M catalyst concentration. The maximum degradation efficiency reached 93.34% for an initial MB concentration of 0.4 × 10⁻⁵ M using 7.5 mg catalyst (0.25 g·L⁻¹), with an apparent reaction rate constant ( k _app) of 4.401 × 10⁻¹ h⁻¹. The presence of the WO 3 − x catalyst enhanced the degradation rate by up to 6 times compared to photolysis. These findings demonstrate the high photocatalytic performance of WO 3 − x obtained from industrial waste, presenting a promising solution for wastewater treatment.


  • Open Access

    Structural, Mechanical, and Radiation Shielding Properties of Epoxy Composites Reinforced with Tungsten Carbide and Hexagonal Boron Nitride

    by Nusret Kaya, Merve Karaman, Raziye Aksoy

    In this work, tungsten carbide (WC) and hexagonal boron nitride ( h BN) have been used as a filler in epoxy resin to a novel composite to enhance the radiation attenuation properties. Four composites were obtained by using various WC/ h BN concentrations. The linear attenuation coefficients of all composites were measured experimentally. At 662keV, the 7W1B composite (%20 epoxy, %40 h BN and %40 WC) had the lowest radiation shielding parameters, including half value length, tenth value layer, and mean free path with the 7.73 cm, 3.356 cm and 2.326 cm values, respectively. Thermal neutron absorption increased proportionally with h BN content, reaching 0.575 cm⁻¹, while fast neutron absorption ranged from 0.0522 to 0.1232 cm⁻¹. Experimental radiation shielding results are supported by theoretical results. In addition, thermal and fast neutron absorption values ​​of the materials were calculated. Thermal neutron absorption values ​​(Σₐ) increased from 0.344 to 0.575 cm⁻¹ with rising h BN content, confirming the contribution of boron-10 isotope in neutron shielding. Similarly, fast neutron absorption values ​​ranged from 0.0522 to 0.1232 cm⁻¹, further supporting the hybrid composite’s potential in mixed radiation environments Mechanical testing revealed that excessive filler loading led to reduced flexural strength due to agglomeration, while balanced compositions achieved better dispersion and structural performance. Thermal analysis indicated enhanced heat conduction with increased WC content. These results demonstrate that WC– h BN–epoxy composites offer a lightweight, efficient, and tunable alternative for radiation shielding in nuclear, aerospace, and defense applications.


  • Fabrication of Carbon Fiber/Silicon Carbide Hybride Polypropylene Composites as Thermal Interface Material

    by Nusret Kaya, Şerafettin Demiç, Merve Karaman

    A wide variety of thermal interface materials (TIMs) used in the electronics semiconductor industry, but heat dissipation is still a problem. Meeting this challenge requires the development of new polymer-based composite materials with improved thermal conductivity. In this study, carbon fiber (CF)/Silicon carbide (SiC) hybrid filler-loaded polypropylene (PP) matrix composites were produced. Thermal properties of composites were investigated by the simultaneous differential thermal analysis, differential scanning calorimeter and thermal conductive measurement system. The mechanical properties of composites were measured by dynamic mechanic analysis and universal mechanical analysis test systems. The molecular structure changes and crystallinity of composites were analyzed by X-ray diffraction analysis. The composites microstructure was identified by scanning electron microscopy technique. The electrical conductivity of the composites investigated with the electrical conductivity measurement technique. The addition of CF into the SiC particles improved thermal degradation and mechanical properties of composites according to only SiC loaded PP matrix. The mixture of 3% CF and 47% SiC particle by weight into the PP matrix improved the thermal conductivity of composites almost 40% than the 50% SiC loaded PP. The viscoelastic properties and the durability of the composites increased with the CF addition.


  • The effect of carbon nanoparticles on cellulosic handsheets

    by Merve Engin, Nusret Kaya

    This article describes the study of the effects of carbon nanoparticles on fibrous cellulosic webs. The handsheets were coated with coating colours containing graphene oxide (GO), carbon nanotube (CNT) and super conductive black carbon (SCBC) nanoparticles at different concentrations. The Raman method was used to assess the quality of the carbon materials and the changes in the band gap of the nanoparticles deposited on the handsheets. The influence of the type and content of the nanoparticles on the structural, mechanical, chemical and electrical properties of the composites was investigated and discussed. It was found that the range of failure modes and fracture surfaces seen in the SEM image is due to the influence of the different carbon materials as the main source of coating colour. The experimental percolation threshold curve and the total surface electrical resistivity of the samples were investigated. The SCBC coated samples exhibited low percolation threshold and comparatively high electrical conductivity at a certain maximum concentration. Each composite exhibited a pronounced stress distribution along the surface layer and the nanoparticle distribution was uniform. The surface resistance of the coated handsheets declined by about 14.103 times with the addition of only 1.0 wt% SCBC compared to the control sample. The composites coated with GO and SCBC nanoparticles at a concentration of 1.0 wt% had the highest tensile strength values.