Ivan Peleshko
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Ivan Peleshko has a total of 20 co-authors. Here are the top co-authors by number of shared publications:
- Vitalina Yurchenko
Kyiv National University of Construction and Architecture
13 shared publications - Dmytro Sydorak
Lviv Polytechnic National University
3 shared publications - Pavlo Rusyn
National Technical University of Ukraine “Igor Sikorsky Kyiv Polytechnic Institute
3 shared publications - Myron Hohol
Lviv Polytechnic National University
2 shared publications - Anatolii Perelmuter
Науково-виробниче об'єднання SCAD Soft
1 shared publication - Ferahim Veliyev
Azerbaijan University of Architecture and Construction
1 shared publication
Latest Publications
- 28 August 2026
- Published by Springer Nature
- p. 433-442
Topology Optimization of Bar Structures Using the Harmony Search Method
- 28 August 2026
- Published by Springer Nature
- p. 433-442
Topology Optimization of Bar Structures Using the Harmony Search Method
- Open Access
- 29 April 2025
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 2 (7 (134)) , 33-40
Estimating deflections of castellated beams using SolidWorks Simulation
The object of this study is a castellated beam, in which the large openings in the web have the shape of a regular hexagon. The beam is investigated for the purpose of assessing deflections. Based on a set of experimental studies, the features of the stress-strain state of castellated beams have been defined. The need to take into account the increased deflections of castellated beams due to the openings in the beam web when calculating the deflections of castellated beams at the serviceability limit state verifications has been determined. A comparative analysis of the deflections obtained as a result of the numerical experiment with the deflections of beams determined using the design code technique has been performed. It was established that for verifications of castellated beams at the serviceability limit state, the error in assessing the deflections of a single-span hinged beam loaded with a uniformly distributed transverse load in some cases reaches 20 %. Recommendations have been devised for estimating deflections of castellated beams. According to the proposed recommendations, the error in estimating castellated beam deflections does not exceed 3 % for the range of the beam span to the total height of its cross-section 8.5<L/h<25. The results are valid only for the range of I-section profiles and only for the case of a uniformly distributed load acting on the beam when the compressed beam flange is out of bending plane restrained and the beam web is perforated with large openings in the form of regular hexagons. It is under such conditions that the results could be implemented in practice both at the stage of selecting cross-sections of the studied class of structures and when designing effective ranges of castellated beams
- 29 April 2025
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 2 (7 (134)) , 33-40
Open AccessEstimating deflections of castellated beams using SolidWorks Simulation
The object of this study is a castellated beam, in which the large openings in the web have the shape of a regular hexagon. The beam is investigated for the purpose of assessing deflections. Based on a set of experimental studies, the features of the stress-strain state of castellated beams have been defined. The need to take into account the increased deflections of castellated beams due to the openings in the beam web when calculating the deflections of castellated beams at the serviceability limit state verifications has been determined. A comparative analysis of the deflections obtained as a result of the numerical experiment with the deflections of beams determined using the design code technique has been performed. It was established that for verifications of castellated beams at the serviceability limit state, the error in assessing the deflections of a single-span hinged beam loaded with a uniformly distributed transverse load in some cases reaches 20 %. Recommendations have been devised for estimating deflections of castellated beams. According to the proposed recommendations, the error in estimating castellated beam deflections does not exceed 3 % for the range of the beam span to the total height of its cross-section 8.5<L/h<25. The results are valid only for the range of I-section profiles and only for the case of a uniformly distributed load acting on the beam when the compressed beam flange is out of bending plane restrained and the beam web is perforated with large openings in the form of regular hexagons. It is under such conditions that the results could be implemented in practice both at the stage of selecting cross-sections of the studied class of structures and when designing effective ranges of castellated beams
- 20 June 2024
- Published by Lviv Polytechnic National University in Theory and Building Practice
- Vol. 2024 (1) , 124-129
FORMULATION OF THE OPTIMIZATION PROBLEM FOR UNDERGROUND ENGINEERING NETWORK ROUTES
The article considers the implementation of methods for optimizing underground external engineering networks in order to reduce construction costs. For this purpose, the problem of optimizing the route of such networks is set in the form of a nonlinear programming problem. The route is modeled by a spatial polyline with rectilinear segments, and the coordinates of its vertices are considered design variables. The ground surface in the designated area is modeled as a continuous function of two coordinates in the plan using BIM technologies, which ensures the automated use of topographic information when calculating the volume of earthworks and checking compliance with constraints specified by standards requirements. The main result of the study is the formulation of the problem of optimizing the route of the engineering network taking into account the terrain.
- 20 June 2024
- Published by Lviv Polytechnic National University in Theory and Building Practice
- Vol. 2024 (1) , 124-129
FORMULATION OF THE OPTIMIZATION PROBLEM FOR UNDERGROUND ENGINEERING NETWORK ROUTES
The article considers the implementation of methods for optimizing underground external engineering networks in order to reduce construction costs. For this purpose, the problem of optimizing the route of such networks is set in the form of a nonlinear programming problem. The route is modeled by a spatial polyline with rectilinear segments, and the coordinates of its vertices are considered design variables. The ground surface in the designated area is modeled as a continuous function of two coordinates in the plan using BIM technologies, which ensures the automated use of topographic information when calculating the volume of earthworks and checking compliance with constraints specified by standards requirements. The main result of the study is the formulation of the problem of optimizing the route of the engineering network taking into account the terrain.
- Open Access
- 3 June 2024
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 3 (7 (129)) , 6-16
Optimization of cross-sectional dimensions of castellated beams with hexagonal openings
The object of this study is a castellated beam, in which the web openings have the shape of a regular hexagon. The beam is examined to find optimal cross-sectional dimensions. The optimization task is stated as the task of finding the optimal profile numbers for top and bottom Tees of the beam and the optimal width of the web opening while ensuring the required load-carrying capacity of the beam. Minimization of the volume of the beam material was considered as an optimality criterion. The stated optimization problem was solved using the exhaustive search method. For an assortment of normal I-beams with parallel flanges, castellated beams were obtained with optimal cross-sectional dimensions depending on the steel grade, the beam span, and the magnitude of transverse uniformly distributed load. The optimization calculations proved that it was possible to increase the elastic section modulus of the beam to 35.48...50 % through the use of a castellated web. Castellated beams with optimal cross-sectional dimensions at the same load-carrying capacity are characterized by lower steel consumption (up to 23.19 %) compared to I-beams with a solid web. Analysis of the results has made it possible to devise recommendations for the optimal distribution of material in the cross-sections of such beams. The results are valid only for the assortment of normal I-beam profiles and only for the case of uniformly distributed load acting on the beam when the compressed beam flange is laterally restrained from the bending plane and the beam web has openings in the form of regular hexagons. It is under such conditions that the reported results can be implemented in practice both at the stage of selecting cross-sections of the studied class of structures, and at the development of effective assortments of castellated beams
- 3 June 2024
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 3 (7 (129)) , 6-16
Open AccessOptimization of cross-sectional dimensions of castellated beams with hexagonal openings
The object of this study is a castellated beam, in which the web openings have the shape of a regular hexagon. The beam is examined to find optimal cross-sectional dimensions. The optimization task is stated as the task of finding the optimal profile numbers for top and bottom Tees of the beam and the optimal width of the web opening while ensuring the required load-carrying capacity of the beam. Minimization of the volume of the beam material was considered as an optimality criterion. The stated optimization problem was solved using the exhaustive search method. For an assortment of normal I-beams with parallel flanges, castellated beams were obtained with optimal cross-sectional dimensions depending on the steel grade, the beam span, and the magnitude of transverse uniformly distributed load. The optimization calculations proved that it was possible to increase the elastic section modulus of the beam to 35.48...50 % through the use of a castellated web. Castellated beams with optimal cross-sectional dimensions at the same load-carrying capacity are characterized by lower steel consumption (up to 23.19 %) compared to I-beams with a solid web. Analysis of the results has made it possible to devise recommendations for the optimal distribution of material in the cross-sections of such beams. The results are valid only for the assortment of normal I-beam profiles and only for the case of uniformly distributed load acting on the beam when the compressed beam flange is laterally restrained from the bending plane and the beam web has openings in the form of regular hexagons. It is under such conditions that the reported results can be implemented in practice both at the stage of selecting cross-sections of the studied class of structures, and at the development of effective assortments of castellated beams
- Open Access
- 21 December 2023
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 6 (7 (126)) , 6-18
Layout and cross-sectional size optimization of truss structures with mixed design variables based on gradient method
The object of the study was truss-type rod structures, which were investigated for the purpose of finding the optimal design solution in a mixed (continuous and discrete) space of variables. The parameters of the geometric scheme of the truss, as well as the dimensions of the cross-sections of its elements, were considered as design variables. The stated optimization problem is represented as a nonlinear programming task, in which the objective function and nonlinear constraints of the mathematical model are continuously differentiable functions of the design variables. The system of constraints includes strength and stability inequalities, formulated for the design cross-sections of the rod elements of the structure, which is subject to the effect of the design load combinations of the ultimate limit states. As a part of the system of constraints, the displacement constraints formulated for the specified structural nodes, which is subject to the action of design load combinations of the serviceability limit states, are considered. To solve the stated optimization problem, a method of the objective function gradient on the surface of active constraints was used, with the simultaneous elimination of residuals in the violated restrictions. For design variables, the variation of which must be performed according to a given set of possible discrete values, a discretization procedure for the optimal solution obtained in the continuous space of design variables is proposed. A comparison of the proposed optimization methodology with alternative metaheuristic methods and algorithms reported in the literature was performed. On the considered problem of parametric optimization of a 47-span tower structure, a design solution with a weight of 835,403 kg was obtained, which is 1.53...4.6 % better than the optimal solutions obtained by other authors
- 21 December 2023
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 6 (7 (126)) , 6-18
Open AccessLayout and cross-sectional size optimization of truss structures with mixed design variables based on gradient method
The object of the study was truss-type rod structures, which were investigated for the purpose of finding the optimal design solution in a mixed (continuous and discrete) space of variables. The parameters of the geometric scheme of the truss, as well as the dimensions of the cross-sections of its elements, were considered as design variables. The stated optimization problem is represented as a nonlinear programming task, in which the objective function and nonlinear constraints of the mathematical model are continuously differentiable functions of the design variables. The system of constraints includes strength and stability inequalities, formulated for the design cross-sections of the rod elements of the structure, which is subject to the effect of the design load combinations of the ultimate limit states. As a part of the system of constraints, the displacement constraints formulated for the specified structural nodes, which is subject to the action of design load combinations of the serviceability limit states, are considered. To solve the stated optimization problem, a method of the objective function gradient on the surface of active constraints was used, with the simultaneous elimination of residuals in the violated restrictions. For design variables, the variation of which must be performed according to a given set of possible discrete values, a discretization procedure for the optimal solution obtained in the continuous space of design variables is proposed. A comparison of the proposed optimization methodology with alternative metaheuristic methods and algorithms reported in the literature was performed. On the considered problem of parametric optimization of a 47-span tower structure, a design solution with a weight of 835,403 kg was obtained, which is 1.53...4.6 % better than the optimal solutions obtained by other authors
- Open Access
- 26 June 2023
- Published by Kyiv National University of Construction and Architecture in Strength of Materials and Theory of Structures
- No. 110,p. 178-198
Parametric optimization of bar structures with discrete and continuous design variables using improved gradient projection method
The paper considers a parametric optimization problem for the bar structures formulated as nonlinear programming task, where the purpose function and non-linear constraints of the mathematical model are continuously differentiable functions of the design variables. The method of the objective function gradient projection onto the active constraints surface with simultaneous correction of the constraints violations has been used to solve the parametric optimization problem. A discretization technique for the design variables that should vary discretely has been proposed. The discretization of the optimal design solution obtained in the continuous space of the design variables is performed by the purposefully selecting discrete points around the point of the continuous optimum. The comparison of the optimization results presented by the paper demonstrates that improved gradient method together with proposed discretization technique for the discrete design variables converges to better solutions of the problem comparing to the meta-heuristic algorithms.
- 26 June 2023
- Published by Kyiv National University of Construction and Architecture in Strength of Materials and Theory of Structures
- No. 110,p. 178-198
Open AccessParametric optimization of bar structures with discrete and continuous design variables using improved gradient projection method
The paper considers a parametric optimization problem for the bar structures formulated as nonlinear programming task, where the purpose function and non-linear constraints of the mathematical model are continuously differentiable functions of the design variables. The method of the objective function gradient projection onto the active constraints surface with simultaneous correction of the constraints violations has been used to solve the parametric optimization problem. A discretization technique for the design variables that should vary discretely has been proposed. The discretization of the optimal design solution obtained in the continuous space of the design variables is performed by the purposefully selecting discrete points around the point of the continuous optimum. The comparison of the optimization results presented by the paper demonstrates that improved gradient method together with proposed discretization technique for the discrete design variables converges to better solutions of the problem comparing to the meta-heuristic algorithms.
- Open Access
- 11 November 2022
- Published by Kyiv National University of Construction and Architecture in Strength of Materials and Theory of Structures
- No. 109,p. 72-92
Searching for a compromise solution in cross-section size optimization problems of cold-formed steel structural members
A parametric optimization problem of cross-sectional sizes for cold-formed steel lipped channel structural members subjected to axial compression has been considered by the paper. An optimization problem is formulated as to define optimum cross-sectional sizes of cold-formed structural member taking into account post-buckling behavior (web and flange local and distortional buckling) of the member as well as structural requirements when the profile perimeter (strip width), profile thickness, design lengths of the structural member as well as material properties are constant and specified in advance. Maximization of the load-carrying capacity of the cold-formed structural member has been assumed as purpose function. The formulated parametric optimization problem has been solved by exhaustive search method using the software written in Python. As optimization results the cold-formed steel lipped channels with optimum cross-sectional dimensions have been obtained depending on the profile thickness and design lengths of the structural member. In order to obtain optimum solutions for cross-sectional dimensions of the CFS lipped channel structural members which are independent from the design flexural lengths and profile thickness, searching for a compromise solution has been performed by exhaustive search method. The obtained cold-formed steel lipped channel structural members with optimum cross-sectional sizes have higher design buckling resistance under the axial compression at the same material consumption (stripe width) comparing with the cold-formed steel lipped channels proposed by the manufacturer. Web local buckling phenomenon has been occurred in all obtained CFS lipped channel cross-sections with optimum sizes.
- 11 November 2022
- Published by Kyiv National University of Construction and Architecture in Strength of Materials and Theory of Structures
- No. 109,p. 72-92
Open AccessSearching for a compromise solution in cross-section size optimization problems of cold-formed steel structural members
A parametric optimization problem of cross-sectional sizes for cold-formed steel lipped channel structural members subjected to axial compression has been considered by the paper. An optimization problem is formulated as to define optimum cross-sectional sizes of cold-formed structural member taking into account post-buckling behavior (web and flange local and distortional buckling) of the member as well as structural requirements when the profile perimeter (strip width), profile thickness, design lengths of the structural member as well as material properties are constant and specified in advance. Maximization of the load-carrying capacity of the cold-formed structural member has been assumed as purpose function. The formulated parametric optimization problem has been solved by exhaustive search method using the software written in Python. As optimization results the cold-formed steel lipped channels with optimum cross-sectional dimensions have been obtained depending on the profile thickness and design lengths of the structural member. In order to obtain optimum solutions for cross-sectional dimensions of the CFS lipped channel structural members which are independent from the design flexural lengths and profile thickness, searching for a compromise solution has been performed by exhaustive search method. The obtained cold-formed steel lipped channel structural members with optimum cross-sectional sizes have higher design buckling resistance under the axial compression at the same material consumption (stripe width) comparing with the cold-formed steel lipped channels proposed by the manufacturer. Web local buckling phenomenon has been occurred in all obtained CFS lipped channel cross-sections with optimum sizes.
- Open Access
- 31 October 2022
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 5 (7 (119)) , 84-95
Optimization of cross-section dimensions of structural members made of cold-formed profiles using compromise search
The object of this study is a structural member made from a C-shaped cold-formed profile, investigated to search for optimal cross-sectional dimensions. The parametric optimization task is stated as the problem to find the optimal cross-sectional dimensions of the structural member under axial compression conditions, taking into account its post-buckling behavior (local buckling of the web and flanges, as well as a distortional buckling of the cross-section) and structural requirements. In this case, the material consumption and mechanical characteristics of steel, as well as the design lengths of the structural member, were considered constant and predefined. The considered criterion of optimality was the maximization of the load-carrying capacity of the structural member for the overall buckling under the axial compression. The stated optimization problem is solved using the method of exhaustive search while applying the developed software. Additionally, for fixed steel consumption, compromise solutions were searched that do not depend on the thickness of the profile and the design lengths of the structural member. The resulting cold-formed C-shaped profiles with optimal cross-sectional dimensions are characterized by a higher load-carrying capacity for the overall buckling under axial compression (to 24.45 % and 22.19 %) at the same steel consumption compared to the profiles offered by the manufacturer. Analysis of the reported results made it possible to devise recommendations for optimal ratios of dimensions and geometric characteristics of the structural members made from C-shaped profiles operating under axial compression. The ratios could be used both at the stage of selection of cross-sections of structural members from cold-formed profiles, and in the development of effective assortments of cold-formed profiles
- 31 October 2022
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 5 (7 (119)) , 84-95
Open AccessOptimization of cross-section dimensions of structural members made of cold-formed profiles using compromise search
The object of this study is a structural member made from a C-shaped cold-formed profile, investigated to search for optimal cross-sectional dimensions. The parametric optimization task is stated as the problem to find the optimal cross-sectional dimensions of the structural member under axial compression conditions, taking into account its post-buckling behavior (local buckling of the web and flanges, as well as a distortional buckling of the cross-section) and structural requirements. In this case, the material consumption and mechanical characteristics of steel, as well as the design lengths of the structural member, were considered constant and predefined. The considered criterion of optimality was the maximization of the load-carrying capacity of the structural member for the overall buckling under the axial compression. The stated optimization problem is solved using the method of exhaustive search while applying the developed software. Additionally, for fixed steel consumption, compromise solutions were searched that do not depend on the thickness of the profile and the design lengths of the structural member. The resulting cold-formed C-shaped profiles with optimal cross-sectional dimensions are characterized by a higher load-carrying capacity for the overall buckling under axial compression (to 24.45 % and 22.19 %) at the same steel consumption compared to the profiles offered by the manufacturer. Analysis of the reported results made it possible to devise recommendations for optimal ratios of dimensions and geometric characteristics of the structural members made from C-shaped profiles operating under axial compression. The ratios could be used both at the stage of selection of cross-sections of structural members from cold-formed profiles, and in the development of effective assortments of cold-formed profiles
- Open Access
- 30 May 2022
- Published by Kyiv National University of Construction and Architecture in Strength of Materials and Theory of Structures
- No. 108,p. 156-170
Optimization cross-sectional dimensions for cold-formed steel lipped channel columns
Parametric optimization problem of cross-sectional sizes for cold-formed C-profiles subjected to central compression has been considered by the paper. Parametric optimization problem for cross-sectional sizes of cold-formed C-profiles has been formulated as follow: to define optimum cross-sectional sizes taking into account post-buckling behavior and structural requirements when stripe width and thickness as well as type of the cold-formed profile are constant and defined by the designer. Criterion of the profile load-bearing capacity maximization has been assumed as purpose function. The latter has been presented in the form of linear convolution of the resistance to central compression taking into account flexural, torsional and torsional-flexural buckling of thin-walled structural member determined according to the requirements EN 1993-1-3:2012 and EN 1993-1-5:2012. Searching for the optimum cross-sectional sizes has been performed taking into account a possibility of post-critical buckling behavior of the structural member based on the local buckling of the web and flanges and/or distortional buckling of the edge fold stiffeners. Formulated parametric optimization problem has been solved using software OptCAD. Update gradient method of the purpose function projection on the active constraints hyperplanes with simultaneous liquidations of the residuals in the constraints has been implemented by the software. As optimization results cold-formed C-profiles have been obtained. With the same stripe width optimum profiles have higher load-bearing capacity level taking into account buckling resistance under central compression comparing with the cold-formed C-profiles proposed by Ukrainian manufacturers. Besides, torsional-flexural buckling resistance of the cold-formed C-profile is determinative for all optimum cross-sectional decisions.
- 30 May 2022
- Published by Kyiv National University of Construction and Architecture in Strength of Materials and Theory of Structures
- No. 108,p. 156-170
Open AccessOptimization cross-sectional dimensions for cold-formed steel lipped channel columns
Parametric optimization problem of cross-sectional sizes for cold-formed C-profiles subjected to central compression has been considered by the paper. Parametric optimization problem for cross-sectional sizes of cold-formed C-profiles has been formulated as follow: to define optimum cross-sectional sizes taking into account post-buckling behavior and structural requirements when stripe width and thickness as well as type of the cold-formed profile are constant and defined by the designer. Criterion of the profile load-bearing capacity maximization has been assumed as purpose function. The latter has been presented in the form of linear convolution of the resistance to central compression taking into account flexural, torsional and torsional-flexural buckling of thin-walled structural member determined according to the requirements EN 1993-1-3:2012 and EN 1993-1-5:2012. Searching for the optimum cross-sectional sizes has been performed taking into account a possibility of post-critical buckling behavior of the structural member based on the local buckling of the web and flanges and/or distortional buckling of the edge fold stiffeners. Formulated parametric optimization problem has been solved using software OptCAD. Update gradient method of the purpose function projection on the active constraints hyperplanes with simultaneous liquidations of the residuals in the constraints has been implemented by the software. As optimization results cold-formed C-profiles have been obtained. With the same stripe width optimum profiles have higher load-bearing capacity level taking into account buckling resistance under central compression comparing with the cold-formed C-profiles proposed by Ukrainian manufacturers. Besides, torsional-flexural buckling resistance of the cold-formed C-profile is determinative for all optimum cross-sectional decisions.
- 15 December 2021
- Published by Lviv Polytechnic National University in Theory and Building Practice
- Vol. 2021 (2) , 24-31
REGULATION OF STRESS-DEFORMED STATE IN COMPRESSED ELEMENTS OF STEEL FRAMES
The article is devoted to the regulation of the stress-strain state in the compressed elements of steel frames under full operating load. It is proposed to perform reinforcement of such elements with different end eccentricities of load application by rational regulation of the stress-strain state in the reinforcement elements. It is shown that the use of SDS adjustment for frame racks increases their bearing capacity and reduces deformability and welds. The new proposed technology of SDS regulation and possible constructive decisions are offered. Numerical experiment revealed high efficiency of application of the proposed solutions during the reconstruction and reinforcement of the metal frame system. The implementation of the proposed method of SDS regulation confirmed its effectiveness.
- 15 December 2021
- Published by Lviv Polytechnic National University in Theory and Building Practice
- Vol. 2021 (2) , 24-31
REGULATION OF STRESS-DEFORMED STATE IN COMPRESSED ELEMENTS OF STEEL FRAMES
The article is devoted to the regulation of the stress-strain state in the compressed elements of steel frames under full operating load. It is proposed to perform reinforcement of such elements with different end eccentricities of load application by rational regulation of the stress-strain state in the reinforcement elements. It is shown that the use of SDS adjustment for frame racks increases their bearing capacity and reduces deformability and welds. The new proposed technology of SDS regulation and possible constructive decisions are offered. Numerical experiment revealed high efficiency of application of the proposed solutions during the reconstruction and reinforcement of the metal frame system. The implementation of the proposed method of SDS regulation confirmed its effectiveness.