Kangkai Tian
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Kangkai Tian has a total of 57 co-authors. Here are the top co-authors by number of shared publications:
- Zi-Hui Zhang
Guangdong University of Technology
19 shared publications - Yonghui Zhang
Hebei university of Technology
16 shared publications - Chunshuang Chu
School of Integrated Circuits, Guangdong University of Technology, Guangzhou, China
11 shared publications - Wengang Bi
The Chinese University of Hong Kong (Shenzhen)
7 shared publications - Hua Shao
School of Electronics and Information Engineering, Hebei University of Technology, Tianjin, China
6 shared publications - Jiamang Che
Hebei Petroleum University of Technology 1 , Chengde 067000
6 shared publications
Latest Publications
- 27 July 2026
- Published by AIP Publishing in Applied Physics Letters
- Vol. 129 (4)
Recorded 1.4 kV/1.24 GW/cm2 BFOM AlGaN/GaN Schottky barrier diodes grown on Si substrate with fan-shaped AlGaN polarization superjunction
In this work, AlGaN/GaN Schottky barrier diodes on silicon (Si) substrates are proposed and fabricated. The proposed devices feature fan-shaped AlGaN polarization field plates (FPs) with a gradient decrease in Al content along the [0001] direction. The resulting negative polarization-induced bulk charges effectively extend the depletion region in the GaN drift layer and homogenize the electric field distribution near both the Schottky contact region and the FP edge. Benefiting from the strong polarization charge-coupling effect enabled by the fan-shaped structures, the electric field can be efficiently modulated while preserving efficient two-dimensional electron gas conduction under forward bias. As a result, the proposed devices achieve a low specific on-resistance (Ron,sp) of ∼1.58 mΩ cm2 together with a high breakdown voltage of ∼1400 V, yielding a recorded Baliga figure of merit of ∼1.24 GW/cm2. Electrical-stress measurements further show a pronounced reduction in dynamic Ron,sp degradation. This confirms that the electron trapping effect is effectively suppressed. These results demonstrate that polarization charge engineering that is combined with fan-shaped FP structures favors a three-dimensional charge-coupling effect. As a result, a highly effective strategy for simultaneously improving static performance and dynamic stability in Si-based GaN power devices has been provided.
- 27 July 2026
- Published by AIP Publishing in Applied Physics Letters
- Vol. 129 (4)
Recorded 1.4 kV/1.24 GW/cm2 BFOM AlGaN/GaN Schottky barrier diodes grown on Si substrate with fan-shaped AlGaN polarization superjunction
In this work, AlGaN/GaN Schottky barrier diodes on silicon (Si) substrates are proposed and fabricated. The proposed devices feature fan-shaped AlGaN polarization field plates (FPs) with a gradient decrease in Al content along the [0001] direction. The resulting negative polarization-induced bulk charges effectively extend the depletion region in the GaN drift layer and homogenize the electric field distribution near both the Schottky contact region and the FP edge. Benefiting from the strong polarization charge-coupling effect enabled by the fan-shaped structures, the electric field can be efficiently modulated while preserving efficient two-dimensional electron gas conduction under forward bias. As a result, the proposed devices achieve a low specific on-resistance (Ron,sp) of ∼1.58 mΩ cm2 together with a high breakdown voltage of ∼1400 V, yielding a recorded Baliga figure of merit of ∼1.24 GW/cm2. Electrical-stress measurements further show a pronounced reduction in dynamic Ron,sp degradation. This confirms that the electron trapping effect is effectively suppressed. These results demonstrate that polarization charge engineering that is combined with fan-shaped FP structures favors a three-dimensional charge-coupling effect. As a result, a highly effective strategy for simultaneously improving static performance and dynamic stability in Si-based GaN power devices has been provided.
- 21 April 2026
- Published by Optica Publishing Group in Optics Letters
- Vol. 51 (9) , 2556-2559
Enhancing the p-type ohmic contact characteristics of deep ultraviolet light-emitting diodes through an Au sacrificial layer without deteriorating the reflectivity
Improving the wall-plug efficiency (WPE) of AlGaN-based deep ultraviolet light-emitting diodes (DUV LEDs) requires the optimization of both the p-type ohmic contact and the reflectivity, which remains a significant challenge. In this study, we employ a simple and effective Au-sacrificial-layer process, achieving the lowest specific contact resistivity of 6.1 × 10 −6 Ω·cm² for the Ni/Rh/Ni/Au contact on p-GaN—6 times reduction compared to the reference device. This approach enhances the p-type ohmic contact via Ga vacancies generated by the annealed Au layer, while the wet-etching reduces optical absorption to preserve the high reflectivity of the p-contact. The DUV LEDs fabricated with the 10-nm Au-sacrificial-layer process exhibit 0.69 V reduction in operating voltage and 15.54% enhancement in WPE at an injection current of 100 mA, compared to the reference device. This research provides a cost-effective strategy to improve the WPE of mass-produced AlGaN-based DUV LEDs.
- 21 April 2026
- Published by Optica Publishing Group in Optics Letters
- Vol. 51 (9) , 2556-2559
Enhancing the p-type ohmic contact characteristics of deep ultraviolet light-emitting diodes through an Au sacrificial layer without deteriorating the reflectivity
Improving the wall-plug efficiency (WPE) of AlGaN-based deep ultraviolet light-emitting diodes (DUV LEDs) requires the optimization of both the p-type ohmic contact and the reflectivity, which remains a significant challenge. In this study, we employ a simple and effective Au-sacrificial-layer process, achieving the lowest specific contact resistivity of 6.1 × 10 −6 Ω·cm² for the Ni/Rh/Ni/Au contact on p-GaN—6 times reduction compared to the reference device. This approach enhances the p-type ohmic contact via Ga vacancies generated by the annealed Au layer, while the wet-etching reduces optical absorption to preserve the high reflectivity of the p-contact. The DUV LEDs fabricated with the 10-nm Au-sacrificial-layer process exhibit 0.69 V reduction in operating voltage and 15.54% enhancement in WPE at an injection current of 100 mA, compared to the reference device. This research provides a cost-effective strategy to improve the WPE of mass-produced AlGaN-based DUV LEDs.
- 16 December 2025
- Published by Wiley in Physica Status Solidi (a)
- Vol. 223 (1)
Numerically Investigate Al 0.78 Ga 0.22 N/Al 0.72 Ga 0.28 N/Al 0.78 Ga 0.22 N p‐Electron Blocking Layer to Manipulate the Carrier Transport for AlGaN‐based Deep‐Ultraviolet Fabry–Pérot Laser Diodes
Due to high ionization energy of Mg impurity and low hole mobility, AlGaN‐based deep‐ultraviolet Fabry–Pérot laser diodes suffer from poor hole injection efficiency and thus low laser power. Here, we design an Al 0.78 Ga 0.22 N (L1)/Al 0.72 Ga 0.28 N (L2)/Al 0.78 Ga 0.22 N (L3) p‐type electron blocking layer (p‐EBL) structure. We find that the proposed p‐EBL affects both thermionic emission and intraband tunneling for holes. Our studies indicate that thin layer L3 favors the hole injection into the layer L2. The very strong polarization‐induced electric field causes hole accumulation at the L1/L2 interface. The other advantage for such a design is that the layer L2 can spatially separate the injection holes and leakage electrons. This will suppress the recombination between holes with leakage electrons in the bulk p‐type region, which further increases the local hole concentration at the L1/L2 interface and helps reduce the valence band barrier height of the layer L1. As a result, the thermionic emission for holes can be enhanced, leading to the enhanced laser power. The simultaneously reduced electron leakage level also suppresses the roll‐over of the laser power for the proposed device. Moreover, if the carrier injection and optical loss are balanced, the performance can be further improved.
- 16 December 2025
- Published by Wiley in Physica Status Solidi (a)
- Vol. 223 (1)
Numerically Investigate Al 0.78 Ga 0.22 N/Al 0.72 Ga 0.28 N/Al 0.78 Ga 0.22 N p‐Electron Blocking Layer to Manipulate the Carrier Transport for AlGaN‐based Deep‐Ultraviolet Fabry–Pérot Laser Diodes
Due to high ionization energy of Mg impurity and low hole mobility, AlGaN‐based deep‐ultraviolet Fabry–Pérot laser diodes suffer from poor hole injection efficiency and thus low laser power. Here, we design an Al 0.78 Ga 0.22 N (L1)/Al 0.72 Ga 0.28 N (L2)/Al 0.78 Ga 0.22 N (L3) p‐type electron blocking layer (p‐EBL) structure. We find that the proposed p‐EBL affects both thermionic emission and intraband tunneling for holes. Our studies indicate that thin layer L3 favors the hole injection into the layer L2. The very strong polarization‐induced electric field causes hole accumulation at the L1/L2 interface. The other advantage for such a design is that the layer L2 can spatially separate the injection holes and leakage electrons. This will suppress the recombination between holes with leakage electrons in the bulk p‐type region, which further increases the local hole concentration at the L1/L2 interface and helps reduce the valence band barrier height of the layer L1. As a result, the thermionic emission for holes can be enhanced, leading to the enhanced laser power. The simultaneously reduced electron leakage level also suppresses the roll‐over of the laser power for the proposed device. Moreover, if the carrier injection and optical loss are balanced, the performance can be further improved.
- 25 July 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electron Device Letters
- Vol. 46 (10) , 1745-1748
Integrating a Photon-Assisted Hole Regenerator Into AlGaN-Based Deep Ultraviolet Light-Emitting Diodes to Boost the Wall-Plug Efficiency
For AlGaN-based deep ultraviolet light-emitting diodes, more than 50% ultraviolet photons are not able to escape from chips despite the ever-designed advanced light extraction structures. In this work, we take the advantage of the unescaped ultraviolet photons to regenerate holes. The photon-assisted hole regenerator in our integrated optoelectronic device consists of a reversely biased n-ZnO/p-GaN structure. Our optical transmittance measurement shows that the n-ZnO layer of as thick as ~70 nm can effectively absorb the ultraviolet emission from the active region, so that the electron-hole pairs can be regenerated. Considering the resistive reversely biased n-ZnO/p-GaN junction, we also design and fabricate n-ZnO microrod matrix so that the p-type ohmic contact is also fabricated on the exposed p-GaN region. Our studies show that the proposed design enhances the wall-plug efficiency by 44%.
- 25 July 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electron Device Letters
- Vol. 46 (10) , 1745-1748
Integrating a Photon-Assisted Hole Regenerator Into AlGaN-Based Deep Ultraviolet Light-Emitting Diodes to Boost the Wall-Plug Efficiency
For AlGaN-based deep ultraviolet light-emitting diodes, more than 50% ultraviolet photons are not able to escape from chips despite the ever-designed advanced light extraction structures. In this work, we take the advantage of the unescaped ultraviolet photons to regenerate holes. The photon-assisted hole regenerator in our integrated optoelectronic device consists of a reversely biased n-ZnO/p-GaN structure. Our optical transmittance measurement shows that the n-ZnO layer of as thick as ~70 nm can effectively absorb the ultraviolet emission from the active region, so that the electron-hole pairs can be regenerated. Considering the resistive reversely biased n-ZnO/p-GaN junction, we also design and fabricate n-ZnO microrod matrix so that the p-type ohmic contact is also fabricated on the exposed p-GaN region. Our studies show that the proposed design enhances the wall-plug efficiency by 44%.
- 24 June 2025
- Published by Optica Publishing Group in Optics Express
- Vol. 33 (13) , 28022-28030
Enhancing deflection efficiency of resonant cavity light-emitting diodes integrating with metagrating via the internal absorption effect
Controlling the light-emitting direction is crucial for the application of micro light-emitting diodes in the display field. Resonant cavity light-emitting diodes (RCLEDs) integrating with metagrating can achieve efficient deflection functionality. In this work, we systematically investigate the impact of the number of TiO2/SiO2 pairs in the upper distributed Bragg reflectors (DBR) and spacing between the RCLED and metagrating on deflection efficiency using a three-dimensional finite-difference time-domain (3D FDTD) method. Compared to 2 and 5 pairs of TiO2/SiO2 in the upper DBR, a higher deflection efficiency is achieved with 3 pairs of TiO2/SiO2. This is because 3 pairs of TiO2/SiO2 can effectively constrain the divergence angles of RCLEDs while minimizing the re-reflection of the non-vertical light from the metagrating back to the metagrating, thereby ensuring that the non-vertical light is gradually absorbed within RCLED. In addition, the deflection efficiency exhibits periodic oscillations as the thickness of the spacer layer. When the thickness of the spacer layer is an even multiple of one-fourth of the wavelength, the deflection efficiency is enhanced. This is because an even-multiple-thickness spacer layer enables a significant portion of the non-vertical light reflected by the metagrating to reach the interior of RCLED, while simultaneously maximizing the prevention of the non-vertical light traveling from the RCLED toward the metagrating.
- 24 June 2025
- Published by Optica Publishing Group in Optics Express
- Vol. 33 (13) , 28022-28030
Enhancing deflection efficiency of resonant cavity light-emitting diodes integrating with metagrating via the internal absorption effect
Controlling the light-emitting direction is crucial for the application of micro light-emitting diodes in the display field. Resonant cavity light-emitting diodes (RCLEDs) integrating with metagrating can achieve efficient deflection functionality. In this work, we systematically investigate the impact of the number of TiO2/SiO2 pairs in the upper distributed Bragg reflectors (DBR) and spacing between the RCLED and metagrating on deflection efficiency using a three-dimensional finite-difference time-domain (3D FDTD) method. Compared to 2 and 5 pairs of TiO2/SiO2 in the upper DBR, a higher deflection efficiency is achieved with 3 pairs of TiO2/SiO2. This is because 3 pairs of TiO2/SiO2 can effectively constrain the divergence angles of RCLEDs while minimizing the re-reflection of the non-vertical light from the metagrating back to the metagrating, thereby ensuring that the non-vertical light is gradually absorbed within RCLED. In addition, the deflection efficiency exhibits periodic oscillations as the thickness of the spacer layer. When the thickness of the spacer layer is an even multiple of one-fourth of the wavelength, the deflection efficiency is enhanced. This is because an even-multiple-thickness spacer layer enables a significant portion of the non-vertical light reflected by the metagrating to reach the interior of RCLED, while simultaneously maximizing the prevention of the non-vertical light traveling from the RCLED toward the metagrating.
- 28 May 2025
- Published by Optica Publishing Group in Optics Letters
- Vol. 50 (11) , 3720-3723
Impact of carrier injection and recombination on the −3 dB bandwidth for GaN-based VCSELs
In this study, we investigate the impact of the carrier transport and recombination on frequency response capability for GaN-based vertical-cavity-surface-emitting laser diodes (VCSELs). The carrier transport and recombination are manipulated by using composition-gradient quantum barriers and a p-type electron-blocking layer. The alloy composition-gradient approach is able to generate polarization bulk charges that favor the polarization self-screening effect to reduce the electric field at heterojunctions. This on the one hand suppresses the quantum confined Stark effect to increase the stimulated recombination rate in the active region. On the other hand, the Al-gradient design enables the decreased electron leakage level. Our results show that the −3 dB bandwidth can be improved either when the stimulated radiative recombination lifetime gets decreased or the escape time for electrons becomes long. As a result, the −3 dB bandwidth can be mostly increased by both decreasing the electron leakage level and increasing the stimulated radiative recombination rate.
- 28 May 2025
- Published by Optica Publishing Group in Optics Letters
- Vol. 50 (11) , 3720-3723
Impact of carrier injection and recombination on the −3 dB bandwidth for GaN-based VCSELs
In this study, we investigate the impact of the carrier transport and recombination on frequency response capability for GaN-based vertical-cavity-surface-emitting laser diodes (VCSELs). The carrier transport and recombination are manipulated by using composition-gradient quantum barriers and a p-type electron-blocking layer. The alloy composition-gradient approach is able to generate polarization bulk charges that favor the polarization self-screening effect to reduce the electric field at heterojunctions. This on the one hand suppresses the quantum confined Stark effect to increase the stimulated recombination rate in the active region. On the other hand, the Al-gradient design enables the decreased electron leakage level. Our results show that the −3 dB bandwidth can be improved either when the stimulated radiative recombination lifetime gets decreased or the escape time for electrons becomes long. As a result, the −3 dB bandwidth can be mostly increased by both decreasing the electron leakage level and increasing the stimulated radiative recombination rate.
- 14 May 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 72 (7) , 3543-3549
A High-Accuracy STT-MTJ SPICE Model Based on Variable Parameters
Fokker–Planck equation (FPE)-based spin-transfer torque magnetic tunnel junction (STT-MTJ) SPICE model demonstrates advantages in terms of time efficiency and the description of magnetic moment dynamics. However, achieving high-accuracy simulation results remains a challenge. In this article, we present a variable parameter model to compensate for the physical effects that are not captured by the FPE. By defining relaxation time and thermal stability factor as functions of effective input current, the model achieves strong agreement with multiple sets of experimental data and reduces the error rate to below 2%. Furthermore, this approach preserves the model’s ability to describe both the dynamic and stochastic characteristics of the STT-MTJ, ensuring its suitability for a broad range of practical applications in circuit simulation. The model is implemented in Verilog-A language, and hybrid circuit simulations prove that it has the ability to work with other standard devices in electronic design automation (EDA) tools, just like HSPICE.
- 14 May 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 72 (7) , 3543-3549
A High-Accuracy STT-MTJ SPICE Model Based on Variable Parameters
Fokker–Planck equation (FPE)-based spin-transfer torque magnetic tunnel junction (STT-MTJ) SPICE model demonstrates advantages in terms of time efficiency and the description of magnetic moment dynamics. However, achieving high-accuracy simulation results remains a challenge. In this article, we present a variable parameter model to compensate for the physical effects that are not captured by the FPE. By defining relaxation time and thermal stability factor as functions of effective input current, the model achieves strong agreement with multiple sets of experimental data and reduces the error rate to below 2%. Furthermore, this approach preserves the model’s ability to describe both the dynamic and stochastic characteristics of the STT-MTJ, ensuring its suitability for a broad range of practical applications in circuit simulation. The model is implemented in Verilog-A language, and hybrid circuit simulations prove that it has the ability to work with other standard devices in electronic design automation (EDA) tools, just like HSPICE.
- Open Access
- 27 September 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Photonics Journal
- Vol. 13 (5) , 1-7
Tuning the Plasmonic Resonance Peak for Al Nanorods on AlGaN Layer to Deep Ultraviolet Band
Tuning the plasmonic resonance peak to the deep ultraviolet (DUV) band is critical for plasmonic-enhanced AlGaN-based DUV photodetector. However,the high refractive index of AlGaN layer seriously limits the plasmonic resonance peak in DUV band. Therefore, in this work, we study how various Al nanoparticles on the AlGaN layer surface affect the plasmonic resonance performance. Compared with the Al-based nanosphere, nanohemisphere and nanodisk, the Al-based nanorod is the most suitable candidate for AlGaN-based DUV photodetectors. This is because the DUV plasmonic dipolar mode excited from the upper part of nanorod is not affected by the interface between the nanorods and the AlGaN layer. However, the interface also leads to another plasmonic dipolar mode at longer wavelengths. Moreover, the DUV plasmonic resonance peak will be influenced by the diameter, the height and the Al 2 O 3 layer thickness. We also find that the diffraction can enhance the resonance peak intensity when the Al nanorod period is smaller than the resonance peak wavelength. Besides, to make the enhanced electric field located in active layer, a layer of Ga 2 O 3 shell is proposed to cover Al nanorods, which causes a quadrupole mode in DUV band excited from the sidewall of Al nanorods.
- 27 September 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Photonics Journal
- Vol. 13 (5) , 1-7
Open AccessTuning the Plasmonic Resonance Peak for Al Nanorods on AlGaN Layer to Deep Ultraviolet Band
Tuning the plasmonic resonance peak to the deep ultraviolet (DUV) band is critical for plasmonic-enhanced AlGaN-based DUV photodetector. However,the high refractive index of AlGaN layer seriously limits the plasmonic resonance peak in DUV band. Therefore, in this work, we study how various Al nanoparticles on the AlGaN layer surface affect the plasmonic resonance performance. Compared with the Al-based nanosphere, nanohemisphere and nanodisk, the Al-based nanorod is the most suitable candidate for AlGaN-based DUV photodetectors. This is because the DUV plasmonic dipolar mode excited from the upper part of nanorod is not affected by the interface between the nanorods and the AlGaN layer. However, the interface also leads to another plasmonic dipolar mode at longer wavelengths. Moreover, the DUV plasmonic resonance peak will be influenced by the diameter, the height and the Al 2 O 3 layer thickness. We also find that the diffraction can enhance the resonance peak intensity when the Al nanorod period is smaller than the resonance peak wavelength. Besides, to make the enhanced electric field located in active layer, a layer of Ga 2 O 3 shell is proposed to cover Al nanorods, which causes a quadrupole mode in DUV band excited from the sidewall of Al nanorods.
- Open Access
- 24 September 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Photonics Journal
- Vol. 13 (5) , 1-5
Polarization Self-Screened Multiple Quantum Wells for Deep Ultraviolet Light-Emitting Diodes to Enhance the Optical Power
We experimentally and numerically propose a deep ultraviolet light-emitting diode (DUV LED) possessing the quantum barriers (QBs) with the gradually reduced Al composition along the [0001] orientation. The induced negative polarization bulk charges in the graded QBs can screen the positive polarization sheet charges at the QB/quantum well (QW) interface, i.e., generating the polarization self-screening effect, which weakens the electric field in the QWs. The polarization self-screened feature is important in enhancing the overlap level of the electron and hole wave functions within the active region and increasing the hole injection, thus improving the electroluminescence intensity and the optical power.
- 24 September 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Photonics Journal
- Vol. 13 (5) , 1-5
Open AccessPolarization Self-Screened Multiple Quantum Wells for Deep Ultraviolet Light-Emitting Diodes to Enhance the Optical Power
We experimentally and numerically propose a deep ultraviolet light-emitting diode (DUV LED) possessing the quantum barriers (QBs) with the gradually reduced Al composition along the [0001] orientation. The induced negative polarization bulk charges in the graded QBs can screen the positive polarization sheet charges at the QB/quantum well (QW) interface, i.e., generating the polarization self-screening effect, which weakens the electric field in the QWs. The polarization self-screened feature is important in enhancing the overlap level of the electron and hole wave functions within the active region and increasing the hole injection, thus improving the electroluminescence intensity and the optical power.