Xianggeng Wei
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Xianggeng Wei has a total of 116 co-authors. Here are the top co-authors by number of shared publications:
- Fei Qin
National Key Laboratory of Solid Propulsion, Northwestern Polytechnical University 1 , Xi'an, Shaanxi 710129
24 shared publications Guoqiang He
21 shared publicationsLei Shi
10 shared publicationsGuo-Qiang He
Science and Technology on Combustion, Internal Flow and Thermal-Structure Laboratory, Northwestern Polytechnical University, Xi’an, China
9 shared publications- Jinying Ye
National Key Laboratory of Solid Propulsion, Northwestern Polytechnical University, Xi’an, Shaanxi, 710072, PR China
7 shared publications Fei Qin
6 shared publications
Latest Publications
- 1 October 2026
- Published by AIP Publishing in Physics of Fluids
- Vol. 38 (10)
Impinging atomization regimes and breakup dynamics of a shear-thinning supramolecular gel sheet
Atomization of non-Newtonian gel fluids is of significant importance in two-phase fluid mechanics. To address the difficulty of liquid-sheet breakup caused by the high viscosity of conventional macromolecular gels, this study focuses on supramolecular gelled kerosene with pronounced shear-thinning characteristics and experimentally investigates its atomization and breakup behavior under impinging-jet conditions using high-speed photography, a laser particle-size analyzer, and image-processing techniques. The evolution of spray morphology, discharge coefficient, droplet-size distribution, and breakup mechanisms is analyzed. The results demonstrate that, compared with conventional macromolecular gelled kerosene, supramolecular gelled kerosene exhibits pronounced post-yield shear-thinning behavior, with a Herschel–Bulkley flow behavior index of n=0.0880 in the stable shear-thinning regime, and can form a well-developed spray even at relatively low injection pressure drops. As the injection pressure drop increases, the discharge coefficient continuously decreases from 0.82 to 0.69, corresponding to a reduction of approximately 15.85%. A generalized Reynolds number applicable to non-Newtonian fluids is introduced to interpret this behavior, indicating the influence of the pronounced shear-thinning characteristics on flow resistance. The droplet-size distribution further reveals a transition of the breakup mechanism from a viscosity-dominated regime to a turbulence-dominated regime. This study reveals the atomization characteristics of supramolecular gels and demonstrates the feasibility of employing supramolecular gels as a novel modification strategy for gelled kerosene propellants. The present findings provide experimental guidance for the design and operating-condition selection of impinging injectors, as well as for spray organization and atomization-distance control in gel-propellant rocket and ramjet propulsion systems.
- 1 October 2026
- Published by AIP Publishing in Physics of Fluids
- Vol. 38 (10)
Impinging atomization regimes and breakup dynamics of a shear-thinning supramolecular gel sheet
Atomization of non-Newtonian gel fluids is of significant importance in two-phase fluid mechanics. To address the difficulty of liquid-sheet breakup caused by the high viscosity of conventional macromolecular gels, this study focuses on supramolecular gelled kerosene with pronounced shear-thinning characteristics and experimentally investigates its atomization and breakup behavior under impinging-jet conditions using high-speed photography, a laser particle-size analyzer, and image-processing techniques. The evolution of spray morphology, discharge coefficient, droplet-size distribution, and breakup mechanisms is analyzed. The results demonstrate that, compared with conventional macromolecular gelled kerosene, supramolecular gelled kerosene exhibits pronounced post-yield shear-thinning behavior, with a Herschel–Bulkley flow behavior index of n=0.0880 in the stable shear-thinning regime, and can form a well-developed spray even at relatively low injection pressure drops. As the injection pressure drop increases, the discharge coefficient continuously decreases from 0.82 to 0.69, corresponding to a reduction of approximately 15.85%. A generalized Reynolds number applicable to non-Newtonian fluids is introduced to interpret this behavior, indicating the influence of the pronounced shear-thinning characteristics on flow resistance. The droplet-size distribution further reveals a transition of the breakup mechanism from a viscosity-dominated regime to a turbulence-dominated regime. This study reveals the atomization characteristics of supramolecular gels and demonstrates the feasibility of employing supramolecular gels as a novel modification strategy for gelled kerosene propellants. The present findings provide experimental guidance for the design and operating-condition selection of impinging injectors, as well as for spray organization and atomization-distance control in gel-propellant rocket and ramjet propulsion systems.
- 1 October 2026
- Published by AIP Publishing in Physics of Fluids
- Vol. 38 (10)
Effects of back pressure and injector geometry on the flashing spray characteristics of nitrous oxide under critical conditions
Nitrous oxide (N2O) has emerged as a highly promising green propellant for spacecraft attitude and orbit control systems. However, its high-saturation vapor pressure readily triggers violent non-equilibrium flash phase transition during injection, posing significant challenges to injector flow rate prediction and reliable combustion chamber ignition. This study employs the backlight shadowgraphy technique to investigate the effects of back pressure (0.01–1.00 MPa) and plain-orifice injector geometry (orifice diameter, length-to-diameter ratio, L/D) on the flash spray characteristics of N2O under critical conditions. The experimental results demonstrate that the pressure ratio (Rp) is the dominant factor governing the extent of flash. The flash spray field exhibits a pronounced cooling effect, even inducing a gas–liquid–solid phase transition, with lower back pressures resulting in a significant increase in solid particles; L/D has a comparatively weak effect on spray development and discharge characteristics within the investigated range; in contrast, increasing the orifice diameter leads to a power-law decrease in the manifold pressure, which significantly weakens the flashing intensity. Based on the present experimental data, an empirical correlation is established for predicting the flow rate of N2O plain-orifice injectors within the investigated flashing critical flow regime and geometric range. These findings contribute experimental data and a theoretical foundation to fundamental investigations of flash phase-change kinetics in multiphase systems.
- 1 October 2026
- Published by AIP Publishing in Physics of Fluids
- Vol. 38 (10)
Effects of back pressure and injector geometry on the flashing spray characteristics of nitrous oxide under critical conditions
Nitrous oxide (N2O) has emerged as a highly promising green propellant for spacecraft attitude and orbit control systems. However, its high-saturation vapor pressure readily triggers violent non-equilibrium flash phase transition during injection, posing significant challenges to injector flow rate prediction and reliable combustion chamber ignition. This study employs the backlight shadowgraphy technique to investigate the effects of back pressure (0.01–1.00 MPa) and plain-orifice injector geometry (orifice diameter, length-to-diameter ratio, L/D) on the flash spray characteristics of N2O under critical conditions. The experimental results demonstrate that the pressure ratio (Rp) is the dominant factor governing the extent of flash. The flash spray field exhibits a pronounced cooling effect, even inducing a gas–liquid–solid phase transition, with lower back pressures resulting in a significant increase in solid particles; L/D has a comparatively weak effect on spray development and discharge characteristics within the investigated range; in contrast, increasing the orifice diameter leads to a power-law decrease in the manifold pressure, which significantly weakens the flashing intensity. Based on the present experimental data, an empirical correlation is established for predicting the flow rate of N2O plain-orifice injectors within the investigated flashing critical flow regime and geometric range. These findings contribute experimental data and a theoretical foundation to fundamental investigations of flash phase-change kinetics in multiphase systems.
- Open Access
- 1 July 2026
- Published by KEAI Publishing in Defence Technology
- Vol. 61, 250-260
Research on the influence of nano-metal additives on the combustion performance of kerosene in a wide-range ramjet combined engine
- 1 July 2026
- Published by KEAI Publishing in Defence Technology
- Vol. 61, 250-260
Open AccessResearch on the influence of nano-metal additives on the combustion performance of kerosene in a wide-range ramjet combined engine
- 23 April 2026
- Published by Elsevier in Aerospace Science and Technology
- Vol. 178
Experimental study on the operating characteristics of a nitrous oxide/kerosene pintle-type throttling rocket engine
- 23 April 2026
- Published by Elsevier in Aerospace Science and Technology
- Vol. 178
Experimental study on the operating characteristics of a nitrous oxide/kerosene pintle-type throttling rocket engine
- 12 February 2026
- Published by Elsevier in Acta Astronautica
- Vol. 244, 214-222
Efficient wide pressure range characterization of solid propellant dynamic burning rate and pressure exponent
- 12 February 2026
- Published by Elsevier in Acta Astronautica
- Vol. 244, 214-222
Efficient wide pressure range characterization of solid propellant dynamic burning rate and pressure exponent
- Open Access
- 2 July 2025
- Published by Elsevier in Chinese Journal of Aeronautics
- Vol. 39 (1)
Dynamic characteristics and sensitivity of water hammer problems in liquid propulsion system using lattice Boltzmann method with entropy limiter
- 2 July 2025
- Published by Elsevier in Chinese Journal of Aeronautics
- Vol. 39 (1)
Open AccessDynamic characteristics and sensitivity of water hammer problems in liquid propulsion system using lattice Boltzmann method with entropy limiter
- 21 June 2025
- Published by Elsevier in Aerospace Science and Technology
- Vol. 165
Numerical study on the influence of plug nozzle expansion ratio on RBCC engine performance in ejector mode
- 21 June 2025
- Published by Elsevier in Aerospace Science and Technology
- Vol. 165
Numerical study on the influence of plug nozzle expansion ratio on RBCC engine performance in ejector mode
- 1 August 2024
- Published by AIP Publishing in Physics of Fluids
- Vol. 36 (8)
Mechanisms of electrospray jet formation and atomized droplet motion in pulsed-jet mode
Electrospray (ES) has attracted significant interest due to its advantages in generating uniform droplets and enabling controlled deposition. However, the complex interactions and droplet motion mechanisms between fluids and electric fields are still not well understood. Herein, this study presents a three-dimensional numerical model based on the volume of fluid and Lagrangian approaches to simulate the ES process in the pulsed jet mode. The model accurately captures the morphology and the atomization characteristics in the pulsed jet mode of ES. The effects of voltage and Reynolds number on the length of the non-atomized zone (including quasi-static Taylor cone, transition zone, and jet), diameter of the jet breakup, and atomization characteristics are discussed. Also, the mechanism of atomized droplets is revealed by analyzing the magnitudes of different types of forces imposing on the droplets in the electric field. The results indicate that higher Reynolds numbers lead to increased length of non-atomized zone and diameter of jet breakup, while the elevated voltages enhance atomization. Electric and Coulomb forces are, respectively, the dominant forces of forming the jet and expanding the atomization angle. Coulomb force increases the atomization angle, and electric field force increases the velocity of atomized droplets. Gravity and drag-force effects are relatively negligible throughout the atomization process. These findings contribute to a better understanding of the electrospray mechanisms and provide insights for optimizing electrospray applications.
- 1 August 2024
- Published by AIP Publishing in Physics of Fluids
- Vol. 36 (8)
Mechanisms of electrospray jet formation and atomized droplet motion in pulsed-jet mode
Electrospray (ES) has attracted significant interest due to its advantages in generating uniform droplets and enabling controlled deposition. However, the complex interactions and droplet motion mechanisms between fluids and electric fields are still not well understood. Herein, this study presents a three-dimensional numerical model based on the volume of fluid and Lagrangian approaches to simulate the ES process in the pulsed jet mode. The model accurately captures the morphology and the atomization characteristics in the pulsed jet mode of ES. The effects of voltage and Reynolds number on the length of the non-atomized zone (including quasi-static Taylor cone, transition zone, and jet), diameter of the jet breakup, and atomization characteristics are discussed. Also, the mechanism of atomized droplets is revealed by analyzing the magnitudes of different types of forces imposing on the droplets in the electric field. The results indicate that higher Reynolds numbers lead to increased length of non-atomized zone and diameter of jet breakup, while the elevated voltages enhance atomization. Electric and Coulomb forces are, respectively, the dominant forces of forming the jet and expanding the atomization angle. Coulomb force increases the atomization angle, and electric field force increases the velocity of atomized droplets. Gravity and drag-force effects are relatively negligible throughout the atomization process. These findings contribute to a better understanding of the electrospray mechanisms and provide insights for optimizing electrospray applications.