HOHamdullah Ozturk

Hamdullah Ozturk

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Hamdullah Ozturk has a total of 39 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Design and production of low-profile, easy-to-manufacture microstrip antennas operating in the low frequency range

    by Hamdullah Öztürk

    In this article, design, fabrication, and analysis of low profile, easy fabricated microstrip antennas operating in the 0-2.5 GHz frequency range were carried out. These antennas operate at frequencies of approximately 2.3-2.21-2.16 GHz. The antennas consist of three parts such as patch, substrate, and ground plate. Substrate consists of FR-4 (dielectric coefficient 4.3 and loss tangent 0.025). The other parts, patch and ground plate, are made of copper material (electrical conductivity 5.8e+0.7 S/m). To realize the design of these antennas, Computer Simulation Technique (CST) studio suite microwave software was preferred. The frequency was chosen in the range of 0-2.5 GHz. The antenna was manufactured in order to evaluate the results of the simulations. A portable Vector Network Analyzer (VNA) device was preferred to compare the simulation and fabrication results. The reflection coefficient parameter was considered to evaluate proposed antenna results. The simulation result showed this value to be -23 dB at 2.2576 GHz, while for production this value was found to be 2.1575 GHz and -22.71 dB. It was observed that the simulation and fabrication results were in compatible with each other.

  • Permittivity Extraction of Electrically Thin Samples by Reflection-Only Free-Space Measurements

    by Ugur C. Hasar, Bing Xue, Hamdullah Ozturk, Yunus Kaya, Gokhan Ozturk

    A permittivity extraction procedure is devised for electrically thin samples from reflection-only free-space measurements. Unlike previous studies, this procedure relies on sample-back metal termination measurements especially useful for thinner samples. An objective function independent of antenna transmission characteristics and reference plane position is derived. Minimum and maximum thickness and permittivity values for which our method is applicable are also examined. Free-space measurements at X-band (8.2–12.4 GHz) of a Rogers 4350B sample ( $\approx$ 1.52 mm) and a FR4 sample ( $\approx$ 1.60 mm) were performed to validate our method with a dielectric constant less than 5% variation.


  • Open Access

    Design and Manufacture of a Low-Profile, Ultra-Thin, Cost-Effective, Easy Production Metasurface-Based Polarization Converter With Linear and Circular Polarization Properties Suitable for Different Frequency Bands

    by Hamdullah Ozturk

    In this article, the design and production process of a multipurpose polarization converter with a single-layer feature has been carried out using a low-profile, ultra-thin, cost-effective metasurface for different frequency band applications such as C-band (5.8–8.2 GHz), X-band (8.2–12.4 GHz), Ku-band (12.4–18.0 GHz). The polarization converter (PC) has two different features: Linear polarization (LP) and circular polarization (CP). PC has LP characteristics in the frequency ranges 6.768–7.184 GHz, 10.432–11.856 GHz, 16.896–17.520 GHz. These frequencies (6.768–7.184, 10.432–11.856, 16.896–17.520) also exhibit CP–CP functionality. In addition, it has left-handed circular polarization (LHCP) in the 8.208–8.960 GHz range and right-handed circular polarization (RHCP) in the 13.344–15.888 GHz range. A Computer Simulation Technique (CST) Studio Suite was selected for the design process of the PC. The PC is made of FR4 material and a layer thickness of 1.6 mm. The CUBE 3D device was chosen to carry out the production process. The performance analysis of the proposed converter was implemented in the frequency range of 4–20 GHz.Considering the results, it was observed that the design and production process results of the PC were compatible with each other to the desired extent.


  • Open Access

    A metasurface-based polarization converter designed for different band applications, with circular and linear polarization properties

    by Hamdullah Öztürk

    In this study, design and simulation processes of a simple structure polarization converter preferred for different band applications were carried out. FR-4 material was selected for the middle part and copper material was preferred for the top and bottom (ground). FR-4 material has been selected for the polarization converter (PC). For this material, loss tangent is 0.025, dielectric constant is 4.3 and thickness is 1.6 mm. The simulation of the study was performed using a Computer Simulation Technique (CST) studio suite. Frequency range selected for this study is 4–16 GHz. The simulation was carried out taking into account the frequency-domain solver. Tetrahedral was selected as the mesh type. The aim of the proposed study is to implement a design with different polarization properties. Polarization conversion ratio (PCR) value for PC was found to be greater than 0.9, and it exhibited magnetic properties at all three frequencies where the PCR value was greater than 0.9. PCR value reached 0.99 in the X-band range. PC, which exhibits circular polarization in the C-band frequency range, was observed to have a 90 degree phase shift. Matlab program was preferred in evaluating the CST simulation results and interpreting the reflection coefficient, PCR, ellipticity (e) value, axial ratio (AR) and phase values.

  • Detection of Storage Container and Temperature Effects in Extra Virgin Olive Oil by a Sensitive Microwave Sensor in Transmission Mode

    by Ugur Cem Hasar, Huseyin Korkmaz, Hafize Hasar, Hamdullah Ozturk, Onur Gokgoz

    The storage conditions of olive oil, particularly the type of container and environmental factors, play a crucial role in preserving its natural quality. Improper storage may lead to adverse effects that could pose risks to human health. In this context, a range of sensors, including electronic noses, UV-VIS spectrophotometers, and gas chromatography, have been developed to analyze these factors effectively. While each of these sensors offers distinct advantages, they also have certain limitations, such as low sensitivity, complex setup procedures, and high cost, which restrict their widespread applications. In this study, for the first time in the literature, we proposed a high-quality and sensitive metamaterial (MM)-based Microwave (MW) sensor to monitor the effects of various storage containers (green PET, dark glass, and tinplate) and environmental conditions (temperature variations of 23°C and 60°C) on the electromagnetic properties of extra virgin olive oil over 90 days. The proposed sensor exhibits an outstanding quality factor (110.2) and sensitivity (12.69 %), positioning it as a leading solution compared to similar MM-based MW sensors reported in the literature. Our study reveals that the resonance frequency of the proposed sensor changes over time for oil samples stored in any container type under a given environmental condition. Additionally, oil samples stored in green PET containers exhibit a more significant resonance frequency shift, which can be attributed to their higher dielectric constant. It is also observed that the proposed sensor shows more frequency shifts for samples stored in any type of container as the temperature increases. This shift is closely linked to the intensified interaction between the oil sample and its container.


  • Double-Sided Metamaterial-Inspired Microwave Sensor for Monitoring of Alkali-Silica-Reaction (ASR) in Cement-Based Mortar Samples

    by Ugur C. Hasar, Hamdullah Ozturk, Huseyin Korkmaz

    Ordinary Portland cement (OPC) structures are the simplest and oldest type of cement in use today. Their service lives, however, are largely limited by the alkali-silica-reaction (ASR), which has the potential of producing microstructures throughout OPC structures. There is therefore a need for accurate detection of ASR. In this study, we propose a double-sided metamaterial-inspired microwave sensor for the identification of ASR occurring inside OPC mortar samples. Different from previous studies for ASR detection, our design heavily relies on a resonance phenomenon, resulting in a relatively highly accurate and sensitive detection. The resonator has designed cells operating over 2.6 − 3.95 GHz (S-band) within which microwave signals are very tender to water reactions, giving a high sensitivity for ASR detection. Simulations and experiments were performed for the S-band to validate our sensor. Expansion tests are conducted, and SEM micrographs are taken to support microwave measurements. Confidence interval analysis is conducted to assess the integrity of measurements.

  • Open Access

    Quantification of Honey Adulteration Using a Planar Microstrip Metamaterial-Motivated Sensor and Software-Defined Radio

    by Ugur Cem Hasar, Hafize Hasar, Yunus Kaya, Hamdullah Ozturk, Huseyin Korkmaz, Selahattin Kosunalp, Teodor Iliev, Mohammad Tariqul Islam, Vahid Nayyeri, Omar Mustafa Ramahi

    This work presents the application of a planar microstrip metamaterial (MM)- motivated sensor in the form of a split-ring resonator (SRR) for the detection and quantification of water adulteration in honey samples. The proposed sensor utilizes inexpensive software-defined radio (SDR) measurements, offering a cost-effective solution. Unlike previous MM sensors employing SRR configuration, our proposed MM-motivated sensor is integrated with a microstrip feedline and an additional vertical bar, enhancing its sensing capability. To enable accurate measurements, a simple calibration procedure based on baseline normalization is implemented, allowing for amplitude-only transmission measurements (|S21|) using the SDR. A special sample holder was designed to increase repeatability of measurements. We separately employ two post-processing techniques, namely the rolling average (RA) approach and the Savitzky-Golay (SG) filter, to effectively eliminate ripples in the measured |S21| data obtained from the SDR. For validation and evaluation of the proposed sensor and post-processing techniques, measurements of flower honey samples with water adulteration levels (δ) up to 10% (mass-to-mass basis) were also performed using a vector network analyzer. The resonance frequency of |S21| is utilized as the basis for analysis. We establish a metric function (linear function) that correlates the shift in resonance frequency with the δ. It is observed that this function fits to measured resonance frequency values with an R2 value greater than 0.96 for both post-processing techniques with or without the sample holder. By inverting this function, we can predict δ with considerable accuracy for a given resonance frequency by using another linear function. It is observed that percentage variations between predicted and measured δ values are between 1.54% and 6.46% for testing samples with δ = 5% and δ = 7%.


  • Sensitive Microwave Sensor for Detection and Quantification of Water in Adulterated Honey

    by Hafize Hasar, Ugur Cem Hasar, Yunus Kaya, Hamdullah Ozturk, Huseyin Korkmaz, Kadir Yuzgulec, Muharrem Karaaslan, Amir Ebrahimi, Vahid Nayyeri, Omar M. Ramahi

    Honey is a rich source of sugar and is one of the indispensable ingredients in infant foods. Thus, it can be subjected to adulteration due to its cost. Measurement techniques such as liquid chromatography and near-infrared spectroscopy, used for detecting any adulteration, are expensive and need to be conducted by highly trained personnel for off-line analysis. Microwave measurements, as a fast, simple, and relatively inexpensive analysis, have recently shown great potential in detecting adulteration within honey samples. Nonetheless, sensor types used in such measurements are conventional. In this study, a reflection-type sensitive microwave sensor terminated by a metal back is proposed for the first time in the literature for detection and quantification of water percentage (δ) level (mass-to-mass basis) within water-adulterated honey samples. When compared with other resonance-based microwave cavity sensors, thanks to its eight strips located at the centers of two closed circular loops, it demonstrates superior frequency selectivity and sensitivity (S = 5.13%) validated by full-wave 3D simulations performed by the CST Microwave Studio and equivalent circuit analysis carried out by the ADS software. For example, for ethanol, the proposed sensor gives a frequency shift of more than 1 GHz in the X-band. Resonance frequency shift and variation of the reflection coefficient amplitude (|S11|) are measured at X-band to detect honey samples with up to 8% adulteration level. Three different honey samples (flower honey, highland honey, and thyme honey) were examined to test the performance and applicability of the proposed sensor.


  • Noniterative and Stable Permittivity Extraction of Solid Dielectrics Using a New Formalism Based on Frequency-Domain and Time-Domain Analyses

    by Ugur C. Hasar, Hamdullah Ozturk

    A non-iterative and stable reference-plane-invariant microwave non-resonant method is proposed for accurate and stable relative permittivity ε r extraction of solid samples without the need for information of sample thickness L . The method first evaluates reference plane transformation distances L 01 and L 02 and then calculates L using the location of first peaks (but not their values) of the magnitudes of forward and backward reflection scattering (S-) parameters in the time-domain. After, this information is utilized for non-iterative and stable determination of ε r in frequency-domain. Accuracy and uncertainty analyses are performed to examine the performance of the method. Permittivities of acrylonitrile butadiene styrene and polyethylene dielectric samples were measured by coaxial line (30kHz–26.5 GHz) and free-space (8.2–12.4 GHz) measurements.