Isabelle Brajer
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Isabelle Brajer has a total of 9 co-authors. Here are the top co-authors by number of shared publications:
- Mette Midtgaard
The National Museum of Denmark, Kgs. Lyngby, Denmark
2 shared publications - Michelle Taube
Universidade do Vale do Taquari
2 shared publications - Charlotte Martin de Fonjaudran
Private Conservator
1 shared publication - David Chelazzi
Department of Chemistry “Ugo Schiff” and CSGI, University of Florence, Florence, Italy
1 shared publication - Kathrine Segel
The National Museum of Denmark
1 shared publication - Michele Baglioni
Department of Biotechnology, Chemistry and Pharmacy, University of Siena, Via Aldo Moro 2, 53100 Siena, Italy
1 shared publication
Latest Publications
- 24 July 2020
- Published by Taylor & Francis in Studies in Conservation
- Vol. 65 (sup1) , 284-291
Removing Ingrained Soiling from Medieval Lime-based Wall Paintings Using Nanorestore Gel® Peggy 6 in Combination with Aqueous Cleaning Liquids
This paper describes a cleaning method for removing ingrained carbonaceous dirt from lime-based wall paintings by utilizing hydrogels in combination with aqueous cleaning liquids. Nanorestore Gel® Peggy 6 has a number of advantages over traditional cleaning methods, and it is capable of holding large amounts of liquid, but it limits liquid penetration into the substrate. Cleaning action occurs only at the interface, without affecting the surrounding area or leaving residues. Furthermore, its viscosity makes it an ideal tool for treating irregular, vaulted surfaces. Laboratory experiments conducted on limewashed model tiles were decisive in the design of in situ experiments on fifteenth-century wall paintings. The cleaning efficiency of each method was assessed and quantified using colorimetry, 2-D FTIR mapping and image analysis using Cultural Heritage ImageJ. SEM-EDX was used for seeking residues. Results of both the model and in situ cleaning tests show a significant reduction of ingrained dirt when comparing Nanorestore Gel® Peggy 6 to traditional methods. Best visual results were obtained when cleaning with hydrogel loaded with 5% triammonium citrate was following by swabbing with a wet sponge. However, using water alone with the gel yielded almost as good a result in situ, making cleaning possible without any risk of residues.
- 24 July 2020
- Published by Taylor & Francis in Studies in Conservation
- Vol. 65 (sup1) , 284-291
Removing Ingrained Soiling from Medieval Lime-based Wall Paintings Using Nanorestore Gel® Peggy 6 in Combination with Aqueous Cleaning Liquids
This paper describes a cleaning method for removing ingrained carbonaceous dirt from lime-based wall paintings by utilizing hydrogels in combination with aqueous cleaning liquids. Nanorestore Gel® Peggy 6 has a number of advantages over traditional cleaning methods, and it is capable of holding large amounts of liquid, but it limits liquid penetration into the substrate. Cleaning action occurs only at the interface, without affecting the surrounding area or leaving residues. Furthermore, its viscosity makes it an ideal tool for treating irregular, vaulted surfaces. Laboratory experiments conducted on limewashed model tiles were decisive in the design of in situ experiments on fifteenth-century wall paintings. The cleaning efficiency of each method was assessed and quantified using colorimetry, 2-D FTIR mapping and image analysis using Cultural Heritage ImageJ. SEM-EDX was used for seeking residues. Results of both the model and in situ cleaning tests show a significant reduction of ingrained dirt when comparing Nanorestore Gel® Peggy 6 to traditional methods. Best visual results were obtained when cleaning with hydrogel loaded with 5% triammonium citrate was following by swabbing with a wet sponge. However, using water alone with the gel yielded almost as good a result in situ, making cleaning possible without any risk of residues.
- 21 July 2020
- Published by Taylor & Francis in Studies in Conservation
- Vol. 66 (4) , 230-243
Replicating Medieval Wall Painting Plaster using the Hot-mix Technique
This paper describes attempts to replicate medieval plaster using hot-mixing, where quicklime, aggregate, and water are combined in a single exothermic process. The experimental study aimed to reproduce the structural characteristics of medieval plaster while making sample materials for conservation trials, rendering them more relevant and comparable with the medieval materials on which treatments take place. For wall painting conservation, similar capillarity and permeability are particularly important for trials focusing on consolidation, desalination, and cleaning. These characteristics are greatly influenced by the materials, working protocol, and curing conditions used in the replication process. Replicated plaster and plaster sampled from Gothic wall paintings were analysed to provide data regarding porosity, type of lime, aggregates, and binder/aggregate ratio using thin-section analyses, X-ray diffraction, porosity measurements, and mercury intrusion porosimetry. The comparative study showed a close match between one of the two recreated mortars and the original plaster.
- 21 July 2020
- Published by Taylor & Francis in Studies in Conservation
- Vol. 66 (4) , 230-243
Replicating Medieval Wall Painting Plaster using the Hot-mix Technique
This paper describes attempts to replicate medieval plaster using hot-mixing, where quicklime, aggregate, and water are combined in a single exothermic process. The experimental study aimed to reproduce the structural characteristics of medieval plaster while making sample materials for conservation trials, rendering them more relevant and comparable with the medieval materials on which treatments take place. For wall painting conservation, similar capillarity and permeability are particularly important for trials focusing on consolidation, desalination, and cleaning. These characteristics are greatly influenced by the materials, working protocol, and curing conditions used in the replication process. Replicated plaster and plaster sampled from Gothic wall paintings were analysed to provide data regarding porosity, type of lime, aggregates, and binder/aggregate ratio using thin-section analyses, X-ray diffraction, porosity measurements, and mercury intrusion porosimetry. The comparative study showed a close match between one of the two recreated mortars and the original plaster.
- 25 June 2020
- Published by Taylor & Francis in Journal of Architectural Conservation
- Vol. 26 (3) , 235-246
Hot-mixed lime mortar: historical and analytical evidence of its use in medieval wall painting plaster
This paper presents evidence supported by scientific analyses and historical documents that medieval plasters used for wall paintings in Denmark were, with high probability, produced by mixing quicklime, aggregate and water in an exothermic process, resulting in a mortar referred to as hot-mixed. This process enables the production of plaster with a very high binder content. Previous thin-section analyses were supplemented by recent analyses of samples collected from three medieval wall paintings in Danish churches. Also included in the analyses were plaster samples produced from hot-mixed mortar and samples produced from lime putty mortar. The analyses of the medieval plasters showed an average binder content in the range of two parts lime to one part aggregate. Moreover, lime inclusions, a characteristic of hot-mix, were found in all samples. SEM analyses showed a similar microstructure in the medieval plasters and the samples produced by hot-mixed mortar, while significant differences were found between the medieval plaster and lime putty samples.
- 25 June 2020
- Published by Taylor & Francis in Journal of Architectural Conservation
- Vol. 26 (3) , 235-246
Hot-mixed lime mortar: historical and analytical evidence of its use in medieval wall painting plaster
This paper presents evidence supported by scientific analyses and historical documents that medieval plasters used for wall paintings in Denmark were, with high probability, produced by mixing quicklime, aggregate and water in an exothermic process, resulting in a mortar referred to as hot-mixed. This process enables the production of plaster with a very high binder content. Previous thin-section analyses were supplemented by recent analyses of samples collected from three medieval wall paintings in Danish churches. Also included in the analyses were plaster samples produced from hot-mixed mortar and samples produced from lime putty mortar. The analyses of the medieval plasters showed an average binder content in the range of two parts lime to one part aggregate. Moreover, lime inclusions, a characteristic of hot-mix, were found in all samples. SEM analyses showed a similar microstructure in the medieval plasters and the samples produced by hot-mixed mortar, while significant differences were found between the medieval plaster and lime putty samples.