Giannino Ponchio Camillo
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Giannino Ponchio Camillo has a total of 23 co-authors. Here are the top co-authors by number of shared publications:
- Alexander Wagner
German Aerospace Center (DLR), Institute of Aerodynamics and Flow Technology, 37073 Göttingen, Germany
7 shared publications - Carlo Scalo
School of Mechanical Engineering, Purdue University, West Lafayette, IN 47907, USA
2 shared publications - Takahiko Toki
School of Mechanical Engineering, Purdue University, West Lafayette, IN 47907, USA
2 shared publications - Adriano Cerminara
Sheffield Hallam University
1 shared publication - Bijaylakshmi Saikia
Department of Aerospace Engineering, University of Maryland, College Park, MD 20742, USA
1 shared publication - Christian Dittert
German Aerospace Center (DLR), Institute of Structures and Design, Stuttgart, Germany
1 shared publication
Latest Publications
- Open Access
- 1 February 2025
- Published by AIP Publishing in Physics of Fluids
- Vol. 37 (2)
Transpiration cooling in hypersonic flow and mutual effect on turbulent transition and cooling performance
This work presents recent advancements in the study of film cooling in hypersonic flows, considering experimental and numerical investigations, with the aim to characterize the wall-cooling performance in different coolant injection and baseflow conditions in a Mach number range 2–7.7. The study explores the mutual interaction between the injected coolant film and the boundary-layer flow, with emphasis on the effects of wall blowing on the boundary-layer characteristics, stability, and transition to turbulence, as well as the effect of transition on wall-cooling performance. Considered flow configurations include cases of effusion cooling in both wall-normal or slightly inclined and wall-parallel blowing, different types of coolant, cases of favorable pressure gradient compared to zero pressure gradient, as well as transpiration cooling cases at different blowing ratios and surface geometries. For the transpiration cooling case, experiments in different hypersonic wind tunnel facilities are presented for flat plate and cone geometries, with coolant injected through C/C porous samples, whereas numerical simulations of modeled porous injection are presented for a flat plate and a blunt cone, showing results for the boundary-layer receptivity with coolant injection and the associated effects on transition and cooling performance. A summary of the main findings is provided along with a critical analysis based on a comparative study to evaluate the effect of each configuration, injection strategy, and key parameters on the boundary-layer flow and the feedback on wall-cooling performance. Conclusions are drawn about potential directions of study for the further development and optimization of the film cooling technique for future hypersonic vehicles.
- 1 February 2025
- Published by AIP Publishing in Physics of Fluids
- Vol. 37 (2)
Open AccessTranspiration cooling in hypersonic flow and mutual effect on turbulent transition and cooling performance
This work presents recent advancements in the study of film cooling in hypersonic flows, considering experimental and numerical investigations, with the aim to characterize the wall-cooling performance in different coolant injection and baseflow conditions in a Mach number range 2–7.7. The study explores the mutual interaction between the injected coolant film and the boundary-layer flow, with emphasis on the effects of wall blowing on the boundary-layer characteristics, stability, and transition to turbulence, as well as the effect of transition on wall-cooling performance. Considered flow configurations include cases of effusion cooling in both wall-normal or slightly inclined and wall-parallel blowing, different types of coolant, cases of favorable pressure gradient compared to zero pressure gradient, as well as transpiration cooling cases at different blowing ratios and surface geometries. For the transpiration cooling case, experiments in different hypersonic wind tunnel facilities are presented for flat plate and cone geometries, with coolant injected through C/C porous samples, whereas numerical simulations of modeled porous injection are presented for a flat plate and a blunt cone, showing results for the boundary-layer receptivity with coolant injection and the associated effects on transition and cooling performance. A summary of the main findings is provided along with a critical analysis based on a comparative study to evaluate the effect of each configuration, injection strategy, and key parameters on the boundary-layer flow and the feedback on wall-cooling performance. Conclusions are drawn about potential directions of study for the further development and optimization of the film cooling technique for future hypersonic vehicles.
- Open Access
- 20 January 2025
- Published by Cambridge University Press (CUP) in Journal of Fluid Mechanics
- Vol. 1003, A28
Large-eddy simulations of conical hypersonic turbulent boundary layers over cooled walls via volumetric rescaling method
Large-eddy simulations (LES) of a hypersonic boundary layer on a $7^\circ$ -half-angle cone are performed to investigate the effects of highly cooled walls (wall-to-recovery temperature ratio of $T_w / T_r \sim 0.1$ ) on fully developed turbulence and to validate a newly developed rescaling method based on volumetric flow extraction. Two Reynolds numbers are considered, $Re_m = 4.1 \times 10^6\ \text {m}^{-1}$ and $6.4 \times 10^6\ \text {m}^{-1}$ , at free-stream Mach numbers of $M_\infty = 7.4$ . A comparison with a reference laminar-to-turbulent simulation, capturing the full history of the transitional flow dynamics, reveals that the volumetric rescaling method can generate a synthetic turbulent inflow that preserves the structure of the fluctuations. Equilibrium conditions are recovered after approximately 40 inlet boundary layer thicknesses. Numerical trials show that a longer streamwise extent of the rescaling box increases numerical stability. Analyses of turbulent statistics and flow visualizations reveal strong pressure oscillations, up to $50\,\%$ of local mean pressure near the wall, and two-dimensional longitudinal wave structures resembling second-mode waves, with wavelengths up to 50 % of the boundary layer thickness, and convective Mach numbers of $M_c \simeq 4.5$ . It is shown that their quasi-periodic recurrence in the flow is not an artefact of the rescaling method. Strong and localized temperature fluctuations and spikes in the wall-heat flux are associated with such waves. Very high values of temperature variance near the wall result in oscillations of the wall-heat flux exceeding its average. Instances of near-wall temperature falling below the imposed wall temperature of $T_w=300$ K result in pockets of instantaneous heat flux oriented against the statistical mean direction.- 20 January 2025
- Published by Cambridge University Press (CUP) in Journal of Fluid Mechanics
- Vol. 1003, A28
Open AccessLarge-eddy simulations of conical hypersonic turbulent boundary layers over cooled walls via volumetric rescaling method
Large-eddy simulations (LES) of a hypersonic boundary layer on a $7^\circ$ -half-angle cone are performed to investigate the effects of highly cooled walls (wall-to-recovery temperature ratio of $T_w / T_r \sim 0.1$ ) on fully developed turbulence and to validate a newly developed rescaling method based on volumetric flow extraction. Two Reynolds numbers are considered, $Re_m = 4.1 \times 10^6\ \text {m}^{-1}$ and $6.4 \times 10^6\ \text {m}^{-1}$ , at free-stream Mach numbers of $M_\infty = 7.4$ . A comparison with a reference laminar-to-turbulent simulation, capturing the full history of the transitional flow dynamics, reveals that the volumetric rescaling method can generate a synthetic turbulent inflow that preserves the structure of the fluctuations. Equilibrium conditions are recovered after approximately 40 inlet boundary layer thicknesses. Numerical trials show that a longer streamwise extent of the rescaling box increases numerical stability. Analyses of turbulent statistics and flow visualizations reveal strong pressure oscillations, up to $50\,\%$ of local mean pressure near the wall, and two-dimensional longitudinal wave structures resembling second-mode waves, with wavelengths up to 50 % of the boundary layer thickness, and convective Mach numbers of $M_c \simeq 4.5$ . It is shown that their quasi-periodic recurrence in the flow is not an artefact of the rescaling method. Strong and localized temperature fluctuations and spikes in the wall-heat flux are associated with such waves. Very high values of temperature variance near the wall result in oscillations of the wall-heat flux exceeding its average. Instances of near-wall temperature falling below the imposed wall temperature of $T_w=300$ K result in pockets of instantaneous heat flux oriented against the statistical mean direction. - Open Access
- 1 November 2024
- Published by AIP Publishing in Physics of Fluids
- Vol. 36 (11)
Significance of the smaller scales for hypersonic turbulent boundary layers with focused laser differential interferometry
While designed to suppress disturbances located away from its beam foci, focused laser differential interferometry (FLDI) is known to have some integration of signals along its optical axis. This is especially true for longer-wavelength signals, although smaller-scale flow structures also have a non-infinitesimal sensitivity length. This study investigates the performance of FLDI in a hypersonic turbulent boundary layer to better understand its behavior. FLDI simulations were conducted using both full-scale direct numerical simulation (DNS) and spatially averaged DNS inputs to directly assess the influence of smaller flow structures on FLDI measurements. The full-scale FLDI results indicate that integration along the optical axis likely results in lower FLDI amplitudes than for true point measurements. Comparison with the spatially averaged FLDI simulations reveals the significance of small-scale structures in FLDI signal roll-off and root mean square amplitudes. Further, the influence of FLDI setup parameters on the response across the frequency spectrum are analyzed. Circular, Gaussian beams with smaller widths are verified to present increased performance relative to elliptical or uniform-intensity beams. Also, measurements using distinct differentiation directions suggest an experimental way to measure turbulence isotropy scales. These results have notable implications for understanding hypersonic turbulent boundary-layer dynamics and interpreting experimental data. Distribution Statement A: Approved for Public Release; Distribution is Unlimited. PA# AFRL-2024-4678; Cleared 08/23/2024.
- 1 November 2024
- Published by AIP Publishing in Physics of Fluids
- Vol. 36 (11)
Open AccessSignificance of the smaller scales for hypersonic turbulent boundary layers with focused laser differential interferometry
While designed to suppress disturbances located away from its beam foci, focused laser differential interferometry (FLDI) is known to have some integration of signals along its optical axis. This is especially true for longer-wavelength signals, although smaller-scale flow structures also have a non-infinitesimal sensitivity length. This study investigates the performance of FLDI in a hypersonic turbulent boundary layer to better understand its behavior. FLDI simulations were conducted using both full-scale direct numerical simulation (DNS) and spatially averaged DNS inputs to directly assess the influence of smaller flow structures on FLDI measurements. The full-scale FLDI results indicate that integration along the optical axis likely results in lower FLDI amplitudes than for true point measurements. Comparison with the spatially averaged FLDI simulations reveals the significance of small-scale structures in FLDI signal roll-off and root mean square amplitudes. Further, the influence of FLDI setup parameters on the response across the frequency spectrum are analyzed. Circular, Gaussian beams with smaller widths are verified to present increased performance relative to elliptical or uniform-intensity beams. Also, measurements using distinct differentiation directions suggest an experimental way to measure turbulence isotropy scales. These results have notable implications for understanding hypersonic turbulent boundary-layer dynamics and interpreting experimental data. Distribution Statement A: Approved for Public Release; Distribution is Unlimited. PA# AFRL-2024-4678; Cleared 08/23/2024.
- Open Access
- 15 January 2024
- Published by Forschungszentrum Julich, Zentralbibliothek in Journal of large-scale research facilities JLSRF
- Vol. 9 (1)
High Enthalpy Shock Tunnel Göttingen of the German Aerospace Center (DLR)
The High Enthalpy Shock Tunnel Göttingen (HEG) of the German Aerospace Center (DLR) is one of the major European hypersonic test facilities. It was commissioned for use in 1991 and was utilized since then extensively in a large number of national and international space and hypersonic flight projects. Originally, the facility was designed for the investigation of the influence of high temperature effects such as chemical and thermal relaxation on the aerothermodynamics of entry or re-entry space vehicles. Over the last years its range of operating conditions was subsequently extended. In this framework the main emphasis was to generate test conditions which allow investigating the flow past hypersonic flight configurations from low altitude Mach 6 up to Mach 10 in a wide altitude range. The studies performed in HEG focused on external as well as internal aerodynamics including combustion of hydrogen in supersonic combustion, shock-wave boundary layer interaction, the investigation and control of boundary layer transition in hypersonic flows and hypersonic turbulence.
- 15 January 2024
- Published by Forschungszentrum Julich, Zentralbibliothek in Journal of large-scale research facilities JLSRF
- Vol. 9 (1)
Open AccessHigh Enthalpy Shock Tunnel Göttingen of the German Aerospace Center (DLR)
The High Enthalpy Shock Tunnel Göttingen (HEG) of the German Aerospace Center (DLR) is one of the major European hypersonic test facilities. It was commissioned for use in 1991 and was utilized since then extensively in a large number of national and international space and hypersonic flight projects. Originally, the facility was designed for the investigation of the influence of high temperature effects such as chemical and thermal relaxation on the aerothermodynamics of entry or re-entry space vehicles. Over the last years its range of operating conditions was subsequently extended. In this framework the main emphasis was to generate test conditions which allow investigating the flow past hypersonic flight configurations from low altitude Mach 6 up to Mach 10 in a wide altitude range. The studies performed in HEG focused on external as well as internal aerodynamics including combustion of hydrogen in supersonic combustion, shock-wave boundary layer interaction, the investigation and control of boundary layer transition in hypersonic flows and hypersonic turbulence.
- Open Access
Combined Experimental and Numerical Investigation of a Hypersonic Turbulent Boundary Layer by Means of FLDI and Large-Eddy Simulations
This work investigates a hypersonic turbulent boundary layer over a half angle cone at a wall-to-total temperature ratio of 0.1, and m, in terms of density fluctuations and the convection velocity of density disturbances. Experimental shock tunnel data are collected using a multi-foci Focused Laser Differential Interferometer (FLDI) to probe the boundary layer at several heights. In addition, a high-fidelity, time-resolved Large-Eddy Simulation (LES) of the conical flowfield under the experimentally observed free stream conditions is conducted. The experimentally measured convection velocity of density disturbances is found to follow literature data of pressure disturbances. The spectral distributions evidence the presence of regions with well-defined power laws that are present in pressure spectra. A framework to combine numerical and experimental observations without requiring complex FLDI post-processing strategies is explored using a computational FLDI (cFLDI) on the numerical solution for direct comparisons. Frequency bounds of 160 kHz MHz are evaluated in consideration of the constraining conditions of both experimental and numerical data. Within these limits, the direct comparisons yield good agreement. Furthermore, it is verified that in the present case, the cFLDI algorithm may be replaced with a simple line integral on the numerical solution.Open AccessCombined Experimental and Numerical Investigation of a Hypersonic Turbulent Boundary Layer by Means of FLDI and Large-Eddy Simulations
This work investigates a hypersonic turbulent boundary layer over a half angle cone at a wall-to-total temperature ratio of 0.1, and m, in terms of density fluctuations and the convection velocity of density disturbances. Experimental shock tunnel data are collected using a multi-foci Focused Laser Differential Interferometer (FLDI) to probe the boundary layer at several heights. In addition, a high-fidelity, time-resolved Large-Eddy Simulation (LES) of the conical flowfield under the experimentally observed free stream conditions is conducted. The experimentally measured convection velocity of density disturbances is found to follow literature data of pressure disturbances. The spectral distributions evidence the presence of regions with well-defined power laws that are present in pressure spectra. A framework to combine numerical and experimental observations without requiring complex FLDI post-processing strategies is explored using a computational FLDI (cFLDI) on the numerical solution for direct comparisons. Frequency bounds of 160 kHz MHz are evaluated in consideration of the constraining conditions of both experimental and numerical data. Within these limits, the direct comparisons yield good agreement. Furthermore, it is verified that in the present case, the cFLDI algorithm may be replaced with a simple line integral on the numerical solution. - Open Access
- 1 April 2023
- Published by AIP Publishing in Review of Scientific Instruments
- Vol. 94 (4) , 045102
Focused laser differential interferometry post-processing methodology for flowfields with circular symmetry
An analytic methodology is presented to reconstruct the pressure waveform of flowfields with circular symmetry from the phase shift detected with Focused Laser Differential Interferometry (FLDI). A weak blast wave generated by an electric spark in ambient air is investigated with the proposed approach. Values of separation distance between the differentiating foci of the FLDI Δx of 76, 120, 175, and 252 μm are employed to probe the flowfield at locations between 3 and 50 mm from the spark source. In a subset of these distances, reference measurements of peak pressure obtained with a surface pressure sensor indicate good agreement with the reconstructed data when small separation distances are used. Further analysis of FLDI reconstructed data is conducted using theoretical correlations for N-waves in terms of the distribution of pressure peak amplitude and compression phase as the wave front propagates. Agreement with theory is verified for all differentiation separation distances except the largest, for which peak pressure comparison shows a 10% loss of measured vs predicted value. A computational FLDI is employed to scrutinize the simplifying hypotheses supporting the waveform reconstruction approach. The direct comparison between experimental and computational FLDI output reveals additional discrepancies for intermediate Δx values but very good agreement for the smallest Δx. The proposed methodology is thus verified to be reasonable, upon appropriate minimization of the FLDI differentiation distance. A parametric analysis using computational FLDI indicates the adequate value of FLDI Δx to be 20% or less of the flowfield characteristic length in terms of density gradient.
- 1 April 2023
- Published by AIP Publishing in Review of Scientific Instruments
- Vol. 94 (4) , 045102
Open AccessFocused laser differential interferometry post-processing methodology for flowfields with circular symmetry
An analytic methodology is presented to reconstruct the pressure waveform of flowfields with circular symmetry from the phase shift detected with Focused Laser Differential Interferometry (FLDI). A weak blast wave generated by an electric spark in ambient air is investigated with the proposed approach. Values of separation distance between the differentiating foci of the FLDI Δx of 76, 120, 175, and 252 μm are employed to probe the flowfield at locations between 3 and 50 mm from the spark source. In a subset of these distances, reference measurements of peak pressure obtained with a surface pressure sensor indicate good agreement with the reconstructed data when small separation distances are used. Further analysis of FLDI reconstructed data is conducted using theoretical correlations for N-waves in terms of the distribution of pressure peak amplitude and compression phase as the wave front propagates. Agreement with theory is verified for all differentiation separation distances except the largest, for which peak pressure comparison shows a 10% loss of measured vs predicted value. A computational FLDI is employed to scrutinize the simplifying hypotheses supporting the waveform reconstruction approach. The direct comparison between experimental and computational FLDI output reveals additional discrepancies for intermediate Δx values but very good agreement for the smallest Δx. The proposed methodology is thus verified to be reasonable, upon appropriate minimization of the FLDI differentiation distance. A parametric analysis using computational FLDI indicates the adequate value of FLDI Δx to be 20% or less of the flowfield characteristic length in terms of density gradient.
- Open Access
- 1 February 2022
- Published by Springer Nature in Experiments in Fluids
- Vol. 63 (2) , 1-13
A low-effort and inexpensive methodology to determine beam separation distance of multi-foci FLDI
A new method is presented to measure the separation distance between probing volumes of closely spaced multi-foci Focused Laser Differential Interferometers (FLDI). The accuracy and precision of this distance measurement directly translate into the quality of convection velocity measurements performed by means of arrays of FLDI. The suggested method is based on the detection of a propagating weak blast wave, generated with a simple and inexpensive apparatus using an automotive spark plug. Demonstration is conducted using an FLDI with two foci (D-FLDI). The generated blast wave is probed at multiple distances from its source to verify its weakening into an acoustic pulse, which offers ideal conditions to the proposed methodology. D-FLDI separation distance measurement using the new approach is compared to measurements using beam profiler images and to the alternative currently established in the literature, based on the FLDI response to a moving weak lens. Tests are made on varying internal configurations of the D-FLDI, while the distance between the two systems is kept constant. Results show the present method to have improved accuracy and robustness in comparison with the moving lens approach, while requiring significantly less effort. Measured separation distances obtained from blast wave detections in a single location are within $$0.5 \%$$ of the reference value measured through the beam profiler. This procedure is therefore a practical and reliable alternative to the measurement using beam profiler imaging, with similar quality. Its advantages concern associated costs, flexibility when measuring in constrained spaces such as in proximity to walls, and applicability to systems in which beam imaging is not an option, such as multi-point line FLDI.- 1 February 2022
- Published by Springer Nature in Experiments in Fluids
- Vol. 63 (2) , 1-13
Open AccessA low-effort and inexpensive methodology to determine beam separation distance of multi-foci FLDI
A new method is presented to measure the separation distance between probing volumes of closely spaced multi-foci Focused Laser Differential Interferometers (FLDI). The accuracy and precision of this distance measurement directly translate into the quality of convection velocity measurements performed by means of arrays of FLDI. The suggested method is based on the detection of a propagating weak blast wave, generated with a simple and inexpensive apparatus using an automotive spark plug. Demonstration is conducted using an FLDI with two foci (D-FLDI). The generated blast wave is probed at multiple distances from its source to verify its weakening into an acoustic pulse, which offers ideal conditions to the proposed methodology. D-FLDI separation distance measurement using the new approach is compared to measurements using beam profiler images and to the alternative currently established in the literature, based on the FLDI response to a moving weak lens. Tests are made on varying internal configurations of the D-FLDI, while the distance between the two systems is kept constant. Results show the present method to have improved accuracy and robustness in comparison with the moving lens approach, while requiring significantly less effort. Measured separation distances obtained from blast wave detections in a single location are within $$0.5 \%$$ of the reference value measured through the beam profiler. This procedure is therefore a practical and reliable alternative to the measurement using beam profiler imaging, with similar quality. Its advantages concern associated costs, flexibility when measuring in constrained spaces such as in proximity to walls, and applicability to systems in which beam imaging is not an option, such as multi-point line FLDI. - Open Access
- 27 June 2020
- Published by Springer Nature in Experiments in Fluids
- Vol. 61 (7) , 1-19
Experimental investigation of the effect of transpiration cooling on second mode instabilities in a hypersonic boundary layer
The influence of localized nitrogen transpiration on second mode instabilities in a hypersonic boundary layer is experimentally investigated. The study is conducted using a $$7^\circ$$ half-angle cone with a length of 1100 mm and small nose bluntness at $$0^\circ$$ angle-of-attack. Transpiration is realized through a porous Carbon/Carbon patch of $$44 \times 82$$ mm located near the expected boundary layer transition onset location. Transpiration mass flow rates in the range of 0.05–1% of the equivalent boundary layer edge mass flow rate were used. Experiments were conducted in the High Enthalpy Shock Tunnel Göttingen (HEG) at total enthalpies around 3 MJ/kg and unit Reynolds numbers in the range of $$1.4 \cdot 10^6 \,$$ to $$6.4 \cdot 10^6 \, {\text {m}}^{-1}$$ . Measurements were conducted by means of coaxial thermocouples, Atomic Layer Thermopiles (ALTP), pressure transducers and high-speed schlieren. The present study shows that the most amplified second mode frequencies were shifted to lower values as nitrogen is transpired into the boundary layer. In some cases the instability amplitudes were found to be significantly reduced. The observed frequency reduction was verified to correlate with the change of the relative sonic line height in the boundary layer. The amplitude damping was observed to occur only until the most amplified frequencies were reduced to around 50% of their undisturbed values. When transpiration within this limit was performed shortly upstream of the natural boundary layer transition onset, a transition delay of approximately 17% could be observed. Graphic- 27 June 2020
- Published by Springer Nature in Experiments in Fluids
- Vol. 61 (7) , 1-19
Open AccessExperimental investigation of the effect of transpiration cooling on second mode instabilities in a hypersonic boundary layer
The influence of localized nitrogen transpiration on second mode instabilities in a hypersonic boundary layer is experimentally investigated. The study is conducted using a $$7^\circ$$ half-angle cone with a length of 1100 mm and small nose bluntness at $$0^\circ$$ angle-of-attack. Transpiration is realized through a porous Carbon/Carbon patch of $$44 \times 82$$ mm located near the expected boundary layer transition onset location. Transpiration mass flow rates in the range of 0.05–1% of the equivalent boundary layer edge mass flow rate were used. Experiments were conducted in the High Enthalpy Shock Tunnel Göttingen (HEG) at total enthalpies around 3 MJ/kg and unit Reynolds numbers in the range of $$1.4 \cdot 10^6 \,$$ to $$6.4 \cdot 10^6 \, {\text {m}}^{-1}$$ . Measurements were conducted by means of coaxial thermocouples, Atomic Layer Thermopiles (ALTP), pressure transducers and high-speed schlieren. The present study shows that the most amplified second mode frequencies were shifted to lower values as nitrogen is transpired into the boundary layer. In some cases the instability amplitudes were found to be significantly reduced. The observed frequency reduction was verified to correlate with the change of the relative sonic line height in the boundary layer. The amplitude damping was observed to occur only until the most amplified frequencies were reduced to around 50% of their undisturbed values. When transpiration within this limit was performed shortly upstream of the natural boundary layer transition onset, a transition delay of approximately 17% could be observed. Graphic