Gavin B. M. Vaughan
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Gavin B. M. Vaughan has a total of 201 co-authors. Here are the top co-authors by number of shared publications:
- Anna Yu. Romanchuk
Lomonosov Moscow State University, Leninskie Gory 1, 119991 Moscow, Russia
4 shared publications - Beatrice Ruta
Institut Néel Université Grenoble Alpes and Centre National de la Recherche Scientifique 25 rue des Martyrs -BP 166 38042 cedex Grenoble
4 shared publications - Evgeny Gerber
Frumkin Institute of Physical Chemistry and Electrochemistry, Russian Academy of Sciences, Moscow, Russia
4 shared publications - Kristina O. Kvashnina
Institute of Resource Ecology, Helmholtz-Zentrum Dresden-Rossendorf, Dresden, Germany
4 shared publications - Lucia Amidani
Helmholtz-Zentrum Dresden-Rossendorf, Institute of Resource Ecology, Dresden, Germany
4 shared publications - Stepan Nikolaevich Kalmykov
Department of Chemistry, M. V. Lomonosov Moscow State University, 119991 Moscow, Russian Federation
4 shared publications
Latest Publications
- Open Access
- 20 November 2025
- Published by Royal Society of Chemistry (RSC) in Catalysis Science & Technology
- Vol. 16 (2) , 390-401
X-ray absorption and diffraction computed tomography characterization of deactivation and coking in spray-dried ZSM-5/alumina catalysts
One of the main drawbacks of acid-based heterogeneous catalytic processes involving hydrocarbons is coke formation. Still, research on shaped catalysts remains limited. The main objective of this study was to gain insight on the catalyst deactivation in the methanol-to-hydrocarbon (MTH) reaction. Diffraction and absorption computed tomography experiments were performed on spray dried, hollow semi-spherically shaped ZSM-5/alumina catalysts of approximately 250 microns size. The catalysts were employed in the MTH at two different pressures, resulting in varying degrees of coking. Absorption tomography (0.027 μm3 /voxel) revealed the structural features and sponginess of the shaped catalysts. These are not perfect spheres; they rather have openings as they burst during spray drying process. Further, high resolution powder X-ray diffraction computed tomography slices (0.125 μm3 /voxel) were analyzed by parametric Rietveld refinement. The analysis showed that catalyst and binder overall are rather homogenously spatially distributed within each sphere, but that bubbles and agglomerates of a single phase are frequent. In addition, it is demonstrated that there were no coking gradients across the sphere wall at both partially and fully deactivation. This indicates that the binder and the catalyst shape and size were suitable for the reaction conditions. Indeed, the catalyst lifetime was almost doubled relative to the pure, powdered zeolite catalyst. A series of catalysts with varying degree of deactivation have been fully characterized ex-situ, suggesting significant spillover of coke from the zeolite to the alumina matrix. These findings demonstrate the need for greater efforts to understand the formulation of shaped catalyst objects, where the matrix should not only hold the components together but also support and enhance the overall catalytic process.
- 20 November 2025
- Published by Royal Society of Chemistry (RSC) in Catalysis Science & Technology
- Vol. 16 (2) , 390-401
Open AccessX-ray absorption and diffraction computed tomography characterization of deactivation and coking in spray-dried ZSM-5/alumina catalysts
One of the main drawbacks of acid-based heterogeneous catalytic processes involving hydrocarbons is coke formation. Still, research on shaped catalysts remains limited. The main objective of this study was to gain insight on the catalyst deactivation in the methanol-to-hydrocarbon (MTH) reaction. Diffraction and absorption computed tomography experiments were performed on spray dried, hollow semi-spherically shaped ZSM-5/alumina catalysts of approximately 250 microns size. The catalysts were employed in the MTH at two different pressures, resulting in varying degrees of coking. Absorption tomography (0.027 μm3 /voxel) revealed the structural features and sponginess of the shaped catalysts. These are not perfect spheres; they rather have openings as they burst during spray drying process. Further, high resolution powder X-ray diffraction computed tomography slices (0.125 μm3 /voxel) were analyzed by parametric Rietveld refinement. The analysis showed that catalyst and binder overall are rather homogenously spatially distributed within each sphere, but that bubbles and agglomerates of a single phase are frequent. In addition, it is demonstrated that there were no coking gradients across the sphere wall at both partially and fully deactivation. This indicates that the binder and the catalyst shape and size were suitable for the reaction conditions. Indeed, the catalyst lifetime was almost doubled relative to the pure, powdered zeolite catalyst. A series of catalysts with varying degree of deactivation have been fully characterized ex-situ, suggesting significant spillover of coke from the zeolite to the alumina matrix. These findings demonstrate the need for greater efforts to understand the formulation of shaped catalyst objects, where the matrix should not only hold the components together but also support and enhance the overall catalytic process.
- Open Access
- 3 October 2025
- Published by American Association for the Advancement of Science (AAAS) in Science Advances
- Vol. 11 (40) , eadz7406
Linking the pressure dependence of the structure and thermal stability to α- and β-relaxations in metallic glasses
Glasses derive their functional properties from complex relaxation dynamics that remain enigmatic under extreme conditions. Although the temperature dependence of these relaxation processes is well established, their behavior under high-pressure conditions remains poorly understood due to substantial experimental difficulties. In this study, we use cutting-edge experimental techniques to probe the pressure evolution of the relaxation spectrum in a Zr 46.8 Ti 8.2 Cu 7.5 Ni 10 Be 27.5 metallic glass across gigapascal pressure ranges. Our findings reveal two distinct relaxation mechanisms under high pressure: In the β-relaxation regime, compression drives the system with reduced atomic mobility and enhanced structural disorder, without appreciable density changes. Conversely, α-relaxation under pressure promotes density-driven structural ordering that improves thermal stability. Notably, the transition between these regimes occurs at a constant T / T g,P ratio, independent of applied pressure. These results provide crucial insights for decoupling the competing structural and relaxation contributions to glass stability, establishing a systematic framework for tailoring glass properties through controlled thermomechanical processing.
- 3 October 2025
- Published by American Association for the Advancement of Science (AAAS) in Science Advances
- Vol. 11 (40) , eadz7406
Open AccessLinking the pressure dependence of the structure and thermal stability to α- and β-relaxations in metallic glasses
Glasses derive their functional properties from complex relaxation dynamics that remain enigmatic under extreme conditions. Although the temperature dependence of these relaxation processes is well established, their behavior under high-pressure conditions remains poorly understood due to substantial experimental difficulties. In this study, we use cutting-edge experimental techniques to probe the pressure evolution of the relaxation spectrum in a Zr 46.8 Ti 8.2 Cu 7.5 Ni 10 Be 27.5 metallic glass across gigapascal pressure ranges. Our findings reveal two distinct relaxation mechanisms under high pressure: In the β-relaxation regime, compression drives the system with reduced atomic mobility and enhanced structural disorder, without appreciable density changes. Conversely, α-relaxation under pressure promotes density-driven structural ordering that improves thermal stability. Notably, the transition between these regimes occurs at a constant T / T g,P ratio, independent of applied pressure. These results provide crucial insights for decoupling the competing structural and relaxation contributions to glass stability, establishing a systematic framework for tailoring glass properties through controlled thermomechanical processing.
- Open Access
- 17 February 2025
- Published by International Union of Crystallography (IUCr) in Journal of Synchrotron Radiation
- Vol. 32 (2) , 378-384
Enhancing high-energy powder X-ray diffraction applications using a PILATUS4 CdTe detector
Hybrid photon counting detectors have significantly advanced synchrotron research. In particular, the introduction of large cadmium telluride-based detectors in 2015 enabled a whole new range of high-energy X-ray measurements. This article describes the specifications of the new PILATUS4 cadmium telluride detector and presents results from prototype testing for high-energy powder X-ray diffraction studies conducted at two synchrotrons. The experiments concern time-resolved in situ solid-state reactions at MAX IV (Sweden) and fast-scanning X-ray diffraction computed tomography of a battery cell at the ESRF (France). The detector's high quantum efficiency up to 100 keV, combined with a maximum frame rate of 4000 Hz, enables fast data collection. This study demonstrates how these capabilities contribute to improved time and spatial resolution in high-energy powder X-ray diffraction studies, facilitating advancements in materials, chemical and energy research.
- 17 February 2025
- Published by International Union of Crystallography (IUCr) in Journal of Synchrotron Radiation
- Vol. 32 (2) , 378-384
Open AccessEnhancing high-energy powder X-ray diffraction applications using a PILATUS4 CdTe detector
Hybrid photon counting detectors have significantly advanced synchrotron research. In particular, the introduction of large cadmium telluride-based detectors in 2015 enabled a whole new range of high-energy X-ray measurements. This article describes the specifications of the new PILATUS4 cadmium telluride detector and presents results from prototype testing for high-energy powder X-ray diffraction studies conducted at two synchrotrons. The experiments concern time-resolved in situ solid-state reactions at MAX IV (Sweden) and fast-scanning X-ray diffraction computed tomography of a battery cell at the ESRF (France). The detector's high quantum efficiency up to 100 keV, combined with a maximum frame rate of 4000 Hz, enables fast data collection. This study demonstrates how these capabilities contribute to improved time and spatial resolution in high-energy powder X-ray diffraction studies, facilitating advancements in materials, chemical and energy research.
- Open Access
- 29 May 2024
- Published by Elsevier in Journal of Cultural Heritage
- Vol. 68, 28-37
Potential of synchrotron X-ray diffraction computed tomography (XRDCT) for a 3D non-destructive and/or non-invasive characterisation of cultural heritage geomaterials (CHG)
- 29 May 2024
- Published by Elsevier in Journal of Cultural Heritage
- Vol. 68, 28-37
Open AccessPotential of synchrotron X-ray diffraction computed tomography (XRDCT) for a 3D non-destructive and/or non-invasive characterisation of cultural heritage geomaterials (CHG)
- Open Access
- 27 February 2024
- Published by Royal Society of Chemistry (RSC) in The Analyst
- Vol. 149 (7) , 2059-2072
Synchrotron radiation X-ray diffraction computed tomography (XRDCT): a new tool in cultural heritage and stone conservation for 3D non-destructive probing and phase analysis of inorganic re-treatments
SR X-ray diffraction computed tomography (XRDCT) was used to non-destructively analyse the effects of sequential inorganic-mineral re-treatments on decayed cultural heritage carbonatic stones. It offers new analytical perspectives for conservation science.
- 27 February 2024
- Published by Royal Society of Chemistry (RSC) in The Analyst
- Vol. 149 (7) , 2059-2072
Open AccessSynchrotron radiation X-ray diffraction computed tomography (XRDCT): a new tool in cultural heritage and stone conservation for 3D non-destructive probing and phase analysis of inorganic re-treatments
SR X-ray diffraction computed tomography (XRDCT) was used to non-destructively analyse the effects of sequential inorganic-mineral re-treatments on decayed cultural heritage carbonatic stones. It offers new analytical perspectives for conservation science.
- Open Access
- 28 August 2023
- Published by Elsevier in Materials Today Nano
- Vol. 24
The nature of the atomic-scale Invar effect in Fe-based bulk metallic glasses
- 28 August 2023
- Published by Elsevier in Materials Today Nano
- Vol. 24
Open AccessThe nature of the atomic-scale Invar effect in Fe-based bulk metallic glasses
- Open Access
- 8 August 2023
- Published by AIP Publishing in The Journal of Chemical Physics
- Vol. 159 (6)
Mapping the structural trends in zinc aluminosilicate glasses
The structure of zinc aluminosilicate glasses with the composition (ZnO)x(Al2O3)y(SiO2)1−x−y, where 0 ≤ x < 1, 0 ≤ y < 1, and x + y < 1, was investigated over a wide composition range by combining neutron and high-energy x-ray diffraction with 27Al magic angle spinning nuclear magnetic resonance spectroscopy. The results were interpreted using an analytical model for the composition-dependent structure in which the zinc ions do not act as network formers. Four-coordinated aluminum atoms were found to be in the majority for all the investigated glasses, with five-coordinated aluminum atoms as the main minority species. Mean Al–O bond distances of 1.764(5) and 1.855(5) Å were obtained for the four- and five-coordinated aluminum atoms, respectively. The coordination environment of zinc was not observed to be invariant. Instead, it is dependent on whether zinc plays a predominantly network-modifying or charge-compensating role and, therefore, varies systematically with the glass composition. The Zn–O coordination number and bond distance were found to be 4.36(9) and 2.00(1) Å, respectively, for the network-modifying role vs 5.96(10) and 2.08(1) Å, respectively, for the charge-compensating role. The more open coordination environment of the charge-compensator is related to an enhanced probability of zinc finding bridging oxygen atoms as nearest-neighbors, reflecting a change in the connectivity of the glass network comprising four-coordinated silicon and aluminum atoms as the alumina content is increased.
- 8 August 2023
- Published by AIP Publishing in The Journal of Chemical Physics
- Vol. 159 (6)
Open AccessMapping the structural trends in zinc aluminosilicate glasses
The structure of zinc aluminosilicate glasses with the composition (ZnO)x(Al2O3)y(SiO2)1−x−y, where 0 ≤ x < 1, 0 ≤ y < 1, and x + y < 1, was investigated over a wide composition range by combining neutron and high-energy x-ray diffraction with 27Al magic angle spinning nuclear magnetic resonance spectroscopy. The results were interpreted using an analytical model for the composition-dependent structure in which the zinc ions do not act as network formers. Four-coordinated aluminum atoms were found to be in the majority for all the investigated glasses, with five-coordinated aluminum atoms as the main minority species. Mean Al–O bond distances of 1.764(5) and 1.855(5) Å were obtained for the four- and five-coordinated aluminum atoms, respectively. The coordination environment of zinc was not observed to be invariant. Instead, it is dependent on whether zinc plays a predominantly network-modifying or charge-compensating role and, therefore, varies systematically with the glass composition. The Zn–O coordination number and bond distance were found to be 4.36(9) and 2.00(1) Å, respectively, for the network-modifying role vs 5.96(10) and 2.08(1) Å, respectively, for the charge-compensating role. The more open coordination environment of the charge-compensator is related to an enhanced probability of zinc finding bridging oxygen atoms as nearest-neighbors, reflecting a change in the connectivity of the glass network comprising four-coordinated silicon and aluminum atoms as the alumina content is increased.
- 2 June 2023
- Published by Elsevier in Acta Materialia
- Vol. 255, 119065
Denser glasses relax faster: Enhanced atomic mobility and anomalous particle displacement under in-situ high pressure compression of metallic glasses
- 2 June 2023
- Published by Elsevier in Acta Materialia
- Vol. 255, 119065
Denser glasses relax faster: Enhanced atomic mobility and anomalous particle displacement under in-situ high pressure compression of metallic glasses
- Open Access
- 25 April 2023
- Published by MDPI AG in Inorganics
- Vol. 11 (5) , 186
Exploring the Hydrogen Sorption Capabilities of a Novel Ti-V-Mn-Zr-Nb High-Entropy Alloy
Hydrogen is considered as a clean energy carrier able to achieve the decarbonization of the economy, but its compact, safe, and efficient storage represents an important challenge. Among many materials forming hydrides, this work reports the study of hydrogen sorption properties of a novel bcc high-entropy alloy, Ti0.30V0.25Mn0.10Zr0.10Nb0.25, synthesized by arc melting. In less than 60 s, the alloy fully absorbs hydrogen at room temperature, reaching a capacity of 2.0 H/M (2.98 wt.%). A two-step reaction with hydrogen is confirmed by pressure-composition isotherms, synchrotron X-ray and neutron diffraction: bcc solid solution ↔ bcc monohydride ↔ fcc dihydride. For the second step transformation, the calculated thermodynamic values indicate the formation of a very stable dihydride, with ΔHabs = −97 kJ/molH2. Moreover, the pair distribution function analysis of high-energy synchrotron X-ray scattering data validates a completely random distribution of metal atoms in the fcc dihydride phase, without noticeable lattice strain nor elemental segregation. In situ synchrotron X-ray and neutron diffraction, performed during hydrogen desorption by heating under vacuum, demonstrated full reversibility of the reaction with hydrogen. On the basis of these results, tuning the chemical composition of high-entropy alloys may have great implications in terms of hydrogen sorption properties.
- 25 April 2023
- Published by MDPI AG in Inorganics
- Vol. 11 (5) , 186
Open AccessExploring the Hydrogen Sorption Capabilities of a Novel Ti-V-Mn-Zr-Nb High-Entropy Alloy
Hydrogen is considered as a clean energy carrier able to achieve the decarbonization of the economy, but its compact, safe, and efficient storage represents an important challenge. Among many materials forming hydrides, this work reports the study of hydrogen sorption properties of a novel bcc high-entropy alloy, Ti0.30V0.25Mn0.10Zr0.10Nb0.25, synthesized by arc melting. In less than 60 s, the alloy fully absorbs hydrogen at room temperature, reaching a capacity of 2.0 H/M (2.98 wt.%). A two-step reaction with hydrogen is confirmed by pressure-composition isotherms, synchrotron X-ray and neutron diffraction: bcc solid solution ↔ bcc monohydride ↔ fcc dihydride. For the second step transformation, the calculated thermodynamic values indicate the formation of a very stable dihydride, with ΔHabs = −97 kJ/molH2. Moreover, the pair distribution function analysis of high-energy synchrotron X-ray scattering data validates a completely random distribution of metal atoms in the fcc dihydride phase, without noticeable lattice strain nor elemental segregation. In situ synchrotron X-ray and neutron diffraction, performed during hydrogen desorption by heating under vacuum, demonstrated full reversibility of the reaction with hydrogen. On the basis of these results, tuning the chemical composition of high-entropy alloys may have great implications in terms of hydrogen sorption properties.
- Open Access
- 3 November 2022
- Published by Royal Society of Chemistry (RSC) in Physical Chemistry Chemical Physics
- Vol. 24 (44) , 27075-27085
5D total scattering computed tomography reveals the full reaction mechanism of a bismuth vanadate lithium ion battery anode
5D operando total scattering computed tomography reveals the mechanism of a lithium ion battery electrode which operates by both alloying and conversion reactions, both at the atomic and the microscopic scale.
- 3 November 2022
- Published by Royal Society of Chemistry (RSC) in Physical Chemistry Chemical Physics
- Vol. 24 (44) , 27075-27085
Open Access5D total scattering computed tomography reveals the full reaction mechanism of a bismuth vanadate lithium ion battery anode
5D operando total scattering computed tomography reveals the mechanism of a lithium ion battery electrode which operates by both alloying and conversion reactions, both at the atomic and the microscopic scale.