Milankumar Nandgaonkar
Milankumar Nandgaonkar has a total of 16 co-authors. Here are the top co-authors by number of shared publications:
- Indraneel Naik
College of Engineering Pune
2 shared publications - Prashant Mahadev Patane
Department of Mechanical Engineering, Dr. Vishwanath Karad MIT World Peace University, Kothrud, Pune, India
2 shared publications - Subhash Lahane
Marathwada Institute of Technology
2 shared publications - Aaryan Durgam
Indian Institute of Technology
1 shared publication D. S. Butala
Research and Development, Greaves Cotton Limited, Pune-411 019, Maharashtra, India
1 shared publicationL. G. Navale
Department of Mechanical Engineering, M. E. Society’s College of Engineering, Pune-411 001, Maharashtra, India
1 shared publication
Latest Publications
- 22 March 2023
- Published by Springer Nature
- p. 329-342
Laser-Induced Spark Ignition of Methane-Air Mixtures in Constant Volume Combustion Chamber
- 22 March 2023
- Published by Springer Nature
- p. 329-342
Laser-Induced Spark Ignition of Methane-Air Mixtures in Constant Volume Combustion Chamber
- 17 December 2021
- Published by Springer Nature
- p. 29-55
Mathematical Modeling of Injection and Spray Characteristics of a Diesel Engine: A Review
- 17 December 2021
- Published by Springer Nature
- p. 29-55
Mathematical Modeling of Injection and Spray Characteristics of a Diesel Engine: A Review
- 8 September 2021
- Published by Wiley in Energy Technology
- Vol. 9 (11)
Experimental Investigation of the Collective Impact of Electric Current and Ambient Temperature on the Thermal and Electrical Parameters of Lithium Iron Phosphate Cells
The performance of a lithium‐ion battery depends on the collective impact of discharge current and ambient temperature. Herein, three aspects of such impact are investigated. The first is the relationship between the thermal parameters. At 0 ºC ambient temperature and 1 C discharge rate, the heat generation rate initially increases to more than 50 kW m−3 and then dips by almost 20% due to a consequent rise in battery temperature. The second aspect is the relationship between the thermal and the electrical parameters. The steep rise in battery temperature at low ambient temperatures lifts up the voltage and improves the electrical performance more than expected. The third aspect is the collective impact of ambient temperature and electric current on the battery performance. At 0 °C ambient temperature, an increase in current from 1 to 1.5 C increases the temperature rise rate by more than two. This increases the battery capacity by at least 6% compared with that at a 1 C rate. The investigation results are expected to improve the understanding of the collective impact of current and ambient temperature on battery performance and provide a guideline for developing an optimized thermal management system.
- 8 September 2021
- Published by Wiley in Energy Technology
- Vol. 9 (11)
Experimental Investigation of the Collective Impact of Electric Current and Ambient Temperature on the Thermal and Electrical Parameters of Lithium Iron Phosphate Cells
The performance of a lithium‐ion battery depends on the collective impact of discharge current and ambient temperature. Herein, three aspects of such impact are investigated. The first is the relationship between the thermal parameters. At 0 ºC ambient temperature and 1 C discharge rate, the heat generation rate initially increases to more than 50 kW m−3 and then dips by almost 20% due to a consequent rise in battery temperature. The second aspect is the relationship between the thermal and the electrical parameters. The steep rise in battery temperature at low ambient temperatures lifts up the voltage and improves the electrical performance more than expected. The third aspect is the collective impact of ambient temperature and electric current on the battery performance. At 0 °C ambient temperature, an increase in current from 1 to 1.5 C increases the temperature rise rate by more than two. This increases the battery capacity by at least 6% compared with that at a 1 C rate. The investigation results are expected to improve the understanding of the collective impact of current and ambient temperature on battery performance and provide a guideline for developing an optimized thermal management system.
- 11 April 2021
- Published by Taylor & Francis in Energy Sources, Part A: Recovery, Utilization, and Environmental Effects
- Vol. 47 (1) , 6545-6561
Numerical simulation of combustion characteristics and emission predictions of methane-air and hydrogen-air mixtures in a constant volume combustion chamber using multi-point laser-induced spark ignition
Lean-burn combustion using higher spark energy can enhance the combustion characteristics and emission performance. A laser is electrodeless with a high energy ignition source and can achieve multi-point ignition easily. This paper presents the computational fluid dynamics (CFD) modeling of combustion of methane-air and hydrogen-air mixture in a constant volume combustion chamber (CVCC) by using multi-point laser-induced spark ignition (LISI). The numerical simulation is carried out using ANSYS Fluent software, and a standard turbulence model (k – ε) is used. The pressure-time history and reaction progress was plotted for various equivalence ratios (ϕ). Numerical result shows that multi-point ignition can completely burn methane-air and hydrogen-air mixture in the range of 0.77 to 1.68 and 0.36 to 4.1, respectively. The maximum peak pressure (Pmax) and shortest combustion duration were observed at ϕ of 1.29 for the methane-air mixture and ϕ of 1.0 for the hydrogen-air mixture. The relative error between the numerical and the experimental results from the literature are within 10%. The faster reaction progress was observed for the hydrogen-air mixture compared to the methane-air mixture for all equivalence ratios. Finally, the validated numerical model was used to predict the CO, CO2, and NOx emission trends. For the methane-air mixture, CO emission increases as the equivalence ratio increases. However, the maximum CO2 emissions were observed at stoichiometric conditions. The highest NOx emissions were observed for the hydrogen-air mixture compared to the methane-air mixture at a stoichiometric equivalence ratio.
- 11 April 2021
- Published by Taylor & Francis in Energy Sources, Part A: Recovery, Utilization, and Environmental Effects
- Vol. 47 (1) , 6545-6561
Numerical simulation of combustion characteristics and emission predictions of methane-air and hydrogen-air mixtures in a constant volume combustion chamber using multi-point laser-induced spark ignition
Lean-burn combustion using higher spark energy can enhance the combustion characteristics and emission performance. A laser is electrodeless with a high energy ignition source and can achieve multi-point ignition easily. This paper presents the computational fluid dynamics (CFD) modeling of combustion of methane-air and hydrogen-air mixture in a constant volume combustion chamber (CVCC) by using multi-point laser-induced spark ignition (LISI). The numerical simulation is carried out using ANSYS Fluent software, and a standard turbulence model (k – ε) is used. The pressure-time history and reaction progress was plotted for various equivalence ratios (ϕ). Numerical result shows that multi-point ignition can completely burn methane-air and hydrogen-air mixture in the range of 0.77 to 1.68 and 0.36 to 4.1, respectively. The maximum peak pressure (Pmax) and shortest combustion duration were observed at ϕ of 1.29 for the methane-air mixture and ϕ of 1.0 for the hydrogen-air mixture. The relative error between the numerical and the experimental results from the literature are within 10%. The faster reaction progress was observed for the hydrogen-air mixture compared to the methane-air mixture for all equivalence ratios. Finally, the validated numerical model was used to predict the CO, CO2, and NOx emission trends. For the methane-air mixture, CO emission increases as the equivalence ratio increases. However, the maximum CO2 emissions were observed at stoichiometric conditions. The highest NOx emissions were observed for the hydrogen-air mixture compared to the methane-air mixture at a stoichiometric equivalence ratio.
- 30 June 2020
- Published by Springer Nature
- p. 59-65
Placement of Heated Blocks Under Forced Convection for Enhanced Heat Transfer
- 30 June 2020
- Published by Springer Nature
- p. 59-65
Placement of Heated Blocks Under Forced Convection for Enhanced Heat Transfer
- 9 January 2013
- Published by SAE International in SAE International Journal of Advances and Current Practices in Mobility
- Vol. 1
Simplified Combustion Pressure and NOx Prediction Model for DI Diesel Engine
This paper is focused on the prediction of in-cylinder pressure, temperatures and engine-out NOx. One of the important factors influencing engine output parameters is the rate of heat release, which affects the in-cylinder pressure, temperature and engine out emissions. A single-zone model is formulated for prediction of heat release and in-cylinder pressure. Being a predictive model, this model does not required cylinder pressure as an input. Combustion pressure is predicted by modeling compression pressure, ignition delay, heat release, and heat loss. Required Sub-models have been obtained from the literatures. Fuel burning rate is predicted using Watson model. To retain the computational efficiency and better prediction accuracy a two-zone model has been formulated to predict NOx emissions. Flame temperatures are predicted by enthalpy balance. Thermal NO concentration is predicted by using basic Zeldovich mechanism. Both these models have been validated on a Turbocharged DI Diesel engine, at various speed-load conditions. The predicted results of the in-cylinder pressure histories as well as the nitric oxide emissions are in good agreement with the test data.
- 9 January 2013
- Published by SAE International in SAE International Journal of Advances and Current Practices in Mobility
- Vol. 1
Simplified Combustion Pressure and NOx Prediction Model for DI Diesel Engine
This paper is focused on the prediction of in-cylinder pressure, temperatures and engine-out NOx. One of the important factors influencing engine output parameters is the rate of heat release, which affects the in-cylinder pressure, temperature and engine out emissions. A single-zone model is formulated for prediction of heat release and in-cylinder pressure. Being a predictive model, this model does not required cylinder pressure as an input. Combustion pressure is predicted by modeling compression pressure, ignition delay, heat release, and heat loss. Required Sub-models have been obtained from the literatures. Fuel burning rate is predicted using Watson model. To retain the computational efficiency and better prediction accuracy a two-zone model has been formulated to predict NOx emissions. Flame temperatures are predicted by enthalpy balance. Thermal NO concentration is predicted by using basic Zeldovich mechanism. Both these models have been validated on a Turbocharged DI Diesel engine, at various speed-load conditions. The predicted results of the in-cylinder pressure histories as well as the nitric oxide emissions are in good agreement with the test data.
- Open Access
- 20 September 2012
- Published by Hindawi Limited in Advances in Acoustics and Vibration
- Vol. 2012, 1-6
Fault Detection of Inline Reciprocating Diesel Engine: A Mass and Gas-Torque Approach
Early fault detection and diagnosis for medium-speed diesel engines are important to ensure reliable operation throughout the course of their service. This work presents an investigation of the diesel engine combustion-related fault detection capability of crankshaft torsional vibrations. Proposed methodology state the way of early fault detection in the operating six-cylinder diesel engine. The model of six cylinders DI Diesel engine is developed appropriately. As per the earlier work by the same author the torsional vibration amplitudes are used to superimpose the mass and gas torque. Further mass and gas torque analysis is used to detect fault in the operating engine. The DFT of the measured crankshafts speed, under steady-state operating conditions at constant load shows significant variation of the amplitude of the lowest major harmonic order. This is valid both for uniform operating and faulty conditions and the lowest harmonic orders may be used to correlate its amplitude to the gas pressure torque and mass torque for a given engine. The amplitudes of the lowest harmonic orders (0.5, 1, and 1.5) of the gas pressure torque and mass torque are used to map the fault. A method capable to detect faulty cylinder of operating Kirloskar diesel engine of SL90 Engine-SL8800TA type is developed, based on the phases of the lowest three harmonic orders.
- 20 September 2012
- Published by Hindawi Limited in Advances in Acoustics and Vibration
- Vol. 2012, 1-6
Open AccessFault Detection of Inline Reciprocating Diesel Engine: A Mass and Gas-Torque Approach
Early fault detection and diagnosis for medium-speed diesel engines are important to ensure reliable operation throughout the course of their service. This work presents an investigation of the diesel engine combustion-related fault detection capability of crankshaft torsional vibrations. Proposed methodology state the way of early fault detection in the operating six-cylinder diesel engine. The model of six cylinders DI Diesel engine is developed appropriately. As per the earlier work by the same author the torsional vibration amplitudes are used to superimpose the mass and gas torque. Further mass and gas torque analysis is used to detect fault in the operating engine. The DFT of the measured crankshafts speed, under steady-state operating conditions at constant load shows significant variation of the amplitude of the lowest major harmonic order. This is valid both for uniform operating and faulty conditions and the lowest harmonic orders may be used to correlate its amplitude to the gas pressure torque and mass torque for a given engine. The amplitudes of the lowest harmonic orders (0.5, 1, and 1.5) of the gas pressure torque and mass torque are used to map the fault. A method capable to detect faulty cylinder of operating Kirloskar diesel engine of SL90 Engine-SL8800TA type is developed, based on the phases of the lowest three harmonic orders.