Akheel Ahmed Syed
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Akheel Ahmed Syed has a total of 9 co-authors. Here are the top co-authors by number of shared publications:
Siddaramaiah
Department of Polymer Science and Technology , Sri Jayachamarajendra College of Engineering , Mysore, India
4 shared publicationsMurtuza Ali Syed
Yenepoya Research Centre, Yenepoya University, Deralakatte, Mangalore 575 018, India
2 shared publicationsSania Akhtar
Central Institute of Plastics Engineering and Technology, Mysore 570 016, India
2 shared publicationsAyesha Syeda
Department of Studies in Chemistry, University of Mysore, Mysore-570006, India
1 shared publicationB. Ramaraj
Research and Development Department, Central Institute of Plastics Engineering and Technology, 437/A Hebbal Industrial Area, Mysore 570 016, India
1 shared publication- Murtuza Ali Syed
National University of Science and Technology, Muscat, Sultanate of Oman
1 shared publication
Latest Publications
- 25 August 2011
- Published by Taylor & Francis in Polymer-Plastics Technology and Engineering
- Vol. 50 (12) , 1187-1198
Investigation on Mechanical, Thermal and Morphological Behaviors of Turmeric Spent Incorporated Vinyl Ester Green Composites
This study aimed at utilizing nutraceutical industrial waste and reducing carbon footprints of plastics. Vinyl ester green composites (VEGCs) have been prepared with turmeric spent A (TS) and organically modified layered silicates (o-montmorilonite, MMT) (organoclays). Tensile behavior and impact strength of vinyl ester matrix thermoset composites were characterized. Thermal characteristics of the vinyl ester/MMT/TS green composites were evaluated by using differential scanning calorimetric (DSC), thermogravimetric analysis (TGA) and dynamic mechanical thermal analysis (DMA). Morphological behavior of nanocomposites has been studied by using scanning electron microscopy (SEM) and atomic force microscopy (AFM).
- 25 August 2011
- Published by Taylor & Francis in Polymer-Plastics Technology and Engineering
- Vol. 50 (12) , 1187-1198
Investigation on Mechanical, Thermal and Morphological Behaviors of Turmeric Spent Incorporated Vinyl Ester Green Composites
This study aimed at utilizing nutraceutical industrial waste and reducing carbon footprints of plastics. Vinyl ester green composites (VEGCs) have been prepared with turmeric spent A (TS) and organically modified layered silicates (o-montmorilonite, MMT) (organoclays). Tensile behavior and impact strength of vinyl ester matrix thermoset composites were characterized. Thermal characteristics of the vinyl ester/MMT/TS green composites were evaluated by using differential scanning calorimetric (DSC), thermogravimetric analysis (TGA) and dynamic mechanical thermal analysis (DMA). Morphological behavior of nanocomposites has been studied by using scanning electron microscopy (SEM) and atomic force microscopy (AFM).
- 12 July 2011
- Published by Taylor & Francis in Polymer-Plastics Technology and Engineering
- Vol. 50 (10) , 973-982
Thermal Characteristics of Nanostructured Filler-Incorporated Polyvinylester Nanocomposites
The aim of the present investigation is to probe the influence of organically modified layered silicates (o-montmorilonite, o-MMT) content on mechanical and thermal behaviors of vinyl ester/o-MMT (organoclays) nanocomposites. Polyvinyl ester nanocomposites were synthesized with o-MMT by in-situ polymerization technique. The prepared vinyl ester/o-MMT composites have been characterized for mechanical properties such as tensile properties and impact strength. Thermal characteristics of the vinyl ester/o-MMT nanocomposites were evaluated by using differential scanning calorimeter (DSC), thermogravimetric analysis (TGA) and dynamic mechanical thermal analysis (DMA). The thermal degradation kinetic parameters such as activation energy (Ea) of nanocomposites were evaluated by using three mathematical models, namely Horowitz–Metzger, Coats–Redfern and Broido's methods.
- 12 July 2011
- Published by Taylor & Francis in Polymer-Plastics Technology and Engineering
- Vol. 50 (10) , 973-982
Thermal Characteristics of Nanostructured Filler-Incorporated Polyvinylester Nanocomposites
The aim of the present investigation is to probe the influence of organically modified layered silicates (o-montmorilonite, o-MMT) content on mechanical and thermal behaviors of vinyl ester/o-MMT (organoclays) nanocomposites. Polyvinyl ester nanocomposites were synthesized with o-MMT by in-situ polymerization technique. The prepared vinyl ester/o-MMT composites have been characterized for mechanical properties such as tensile properties and impact strength. Thermal characteristics of the vinyl ester/o-MMT nanocomposites were evaluated by using differential scanning calorimeter (DSC), thermogravimetric analysis (TGA) and dynamic mechanical thermal analysis (DMA). The thermal degradation kinetic parameters such as activation energy (Ea) of nanocomposites were evaluated by using three mathematical models, namely Horowitz–Metzger, Coats–Redfern and Broido's methods.
- 23 August 2010
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 119 (4) , 1889-1895
Studies on the physico‐mechanical, thermal, and morphological behaviors of high density polyethylene/coleus spent green composites
- 23 August 2010
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 119 (4) , 1889-1895
Studies on the physico‐mechanical, thermal, and morphological behaviors of high density polyethylene/coleus spent green composites
- 2 June 2010
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 118 (2) , 1204-1210
Development of environmentally friendly high‐density polyethylene and turmeric spent composites: Physicomechanical, thermal, and morphological studies
High‐density polyethylene (HDPE)/turmeric spent (TS) composites were prepared by the extrusion of an HDPE resin with 5, 10, 15, or 20 wt % TS. HDPE granules and TS master‐batch flakes were compounded on a corotating and intermeshing twin‐screw extruder. The extrudate strands were cut into pellets and injection‐molded to make test specimens. These specimens were tested for physicomechanical properties such as the tensile, flexural, and impact strengths, surface hardness, abrasion resistance, density, and water absorption and thermal characteristics such as the heat distortion temperature (HDT) and melt flow index (MFI). Test results revealed that the incorporation of TS affected the tensile, flexural, and Izod impact strengths of the HDPE/TS composites to some extent, whereas the tensile modulus increased from 606.9 to 752.0 N/mm2 and the HDT increased from 61 to 65°C. Furthermore, the addition of TS yielded only marginal variations in the surface hardness, abrasion resistance, density, water absorption, and MFI values of the composites. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010
- 2 June 2010
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 118 (2) , 1204-1210
Development of environmentally friendly high‐density polyethylene and turmeric spent composites: Physicomechanical, thermal, and morphological studies
High‐density polyethylene (HDPE)/turmeric spent (TS) composites were prepared by the extrusion of an HDPE resin with 5, 10, 15, or 20 wt % TS. HDPE granules and TS master‐batch flakes were compounded on a corotating and intermeshing twin‐screw extruder. The extrudate strands were cut into pellets and injection‐molded to make test specimens. These specimens were tested for physicomechanical properties such as the tensile, flexural, and impact strengths, surface hardness, abrasion resistance, density, and water absorption and thermal characteristics such as the heat distortion temperature (HDT) and melt flow index (MFI). Test results revealed that the incorporation of TS affected the tensile, flexural, and Izod impact strengths of the HDPE/TS composites to some extent, whereas the tensile modulus increased from 606.9 to 752.0 N/mm2 and the HDT increased from 61 to 65°C. Furthermore, the addition of TS yielded only marginal variations in the surface hardness, abrasion resistance, density, water absorption, and MFI values of the composites. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010
- 3 May 2010
- Published by Taylor & Francis in Polymer-Plastics Technology and Engineering
- Vol. 49 (6) , 555-559
Investigation on Physico-Mechanical Properties, Water, Thermal and Chemical Ageing of Unsaturated Polyester/Turmeric Spent Composites
Nutraceutical industrial residues are potential fillers to fabricate green or eco-friendly polymeric composite materials as they are, less costly and easily available. Attempts have been made to use turmeric spent (TS)—a nutraceutical industry waste with a high E-factor to improve need-based properties of plastics. A series of unsaturated polyester resin composites have been fabricated with different turmeric spent content viz., 5, 10, 15 and 20% w/w. The effect of amount of filler content on tensile strength, physical properties including density and surface hardness and chemical resistance of the composites were determined. The influence of water and thermal ageing on the tensile strength of turmeric filler loaded unsaturated polyester composites has been studied.
- 3 May 2010
- Published by Taylor & Francis in Polymer-Plastics Technology and Engineering
- Vol. 49 (6) , 555-559
Investigation on Physico-Mechanical Properties, Water, Thermal and Chemical Ageing of Unsaturated Polyester/Turmeric Spent Composites
Nutraceutical industrial residues are potential fillers to fabricate green or eco-friendly polymeric composite materials as they are, less costly and easily available. Attempts have been made to use turmeric spent (TS)—a nutraceutical industry waste with a high E-factor to improve need-based properties of plastics. A series of unsaturated polyester resin composites have been fabricated with different turmeric spent content viz., 5, 10, 15 and 20% w/w. The effect of amount of filler content on tensile strength, physical properties including density and surface hardness and chemical resistance of the composites were determined. The influence of water and thermal ageing on the tensile strength of turmeric filler loaded unsaturated polyester composites has been studied.
- Open Access
- 26 November 2007
- Published by African Journals Online (AJOL) in Bulletin of the Chemical Society of Ethiopia
- Vol. 21 (3) , 315-321
NEOCUPROINE AND BATHOCUPROINE AS NEW REAGENTS FOR THE SPECTROPHOTOMETRIC DETERMINATION OF CERTAIN PROTON PUMP INHIBITORS
NEOCUPROINE AND BATHOCUPROINE AS NEW REAGENTS FOR THE SPECTROPHOTOMETRIC DETERMINATION OF CERTAIN PROTON PUMP INHIBITORS
- 26 November 2007
- Published by African Journals Online (AJOL) in Bulletin of the Chemical Society of Ethiopia
- Vol. 21 (3) , 315-321
Open AccessNEOCUPROINE AND BATHOCUPROINE AS NEW REAGENTS FOR THE SPECTROPHOTOMETRIC DETERMINATION OF CERTAIN PROTON PUMP INHIBITORS
NEOCUPROINE AND BATHOCUPROINE AS NEW REAGENTS FOR THE SPECTROPHOTOMETRIC DETERMINATION OF CERTAIN PROTON PUMP INHIBITORS