Ki-Su Kim
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Ki-Su Kim has a total of 33 co-authors. Here are the top co-authors by number of shared publications:
- Myung-Il Roh
Department of Naval Architecture and Ocean Engineering, and Research Institute of Marine Systems Engineering, Seoul National University , 1 Gwanak-ro, Gwanak-gu, Seoul 08826
7 shared publications Dong-Guen Jeong
1 shared publicationDong-Young Gu
Department of Medicine, Dong-Eui University College of Oriental Medicine, Cardiac and Vascular Center, Dong-Eui Medical Center, Busan, Korea
1 shared publicationEun-Sil Sung
1 shared publication- Gap-Heon Lee
ICT Solution Team, Korean Register, Busan 46762, Korea
1 shared publication - Han-Sung Kim
Technology Strategy Department, Daewoo Shipbuilding and Marine Engineering, 125 Namdaemun-ro, Jung-gu, Seoul 04521, South Korea
1 shared publication
Latest Publications
- Open Access
- 3 February 2025
- Published by Elsevier in International Journal of Naval Architecture and Ocean Engineering
- Vol. 17
A route planning method for small ships in coastal areas based on quadtree
- 3 February 2025
- Published by Elsevier in International Journal of Naval Architecture and Ocean Engineering
- Vol. 17
Open AccessA route planning method for small ships in coastal areas based on quadtree
- 20 December 2024
- Published by The Society of Naval Architects of Korea in Journal of the Society of Naval Architects of Korea
- Vol. 61 (6) , 524-531
Improvement of Loading Computer for RoPax Using Image Recognition Technique
One of the most prevalent maritime accidents that continues to occur is the loss of stability. This issue is particularly common in RoRo or RoPax ships, which have a high center of gravity. Due to the nature of these ships, which transport vehicles, it is difficult to accurately estimate stability because the cargo weight and loading positions are not standardized. Therefore, this study proposes a method to improve the loading computer using image recognition technology. First, the axle load of cargo vehicles waiting to board the ship is measured. Second, the vehicle's license plate and type are recognized. The position of the vehicles is then tracked using the recognized license plate information and cameras mounted on each deck and ramp. Finally, once the vehicle stops, this information is transmitted to the loading computer. We applied the proposed method to RoPax vessels to evaluate their effectiveness. We modeled a total of two decks and loaded 60 vehicles to verify whether the positions of these vehicles were accurately received by the loading computer through interface. loading plan was then utilized to assess the ship's stability. This confirmed that the proposed method can be used to improve the accuracy of stability assessments by eliminating human error. As a result, more precise and reliable evaluations of a ship's stability can be achieved using proposed approach.
- 20 December 2024
- Published by The Society of Naval Architects of Korea in Journal of the Society of Naval Architects of Korea
- Vol. 61 (6) , 524-531
Improvement of Loading Computer for RoPax Using Image Recognition Technique
One of the most prevalent maritime accidents that continues to occur is the loss of stability. This issue is particularly common in RoRo or RoPax ships, which have a high center of gravity. Due to the nature of these ships, which transport vehicles, it is difficult to accurately estimate stability because the cargo weight and loading positions are not standardized. Therefore, this study proposes a method to improve the loading computer using image recognition technology. First, the axle load of cargo vehicles waiting to board the ship is measured. Second, the vehicle's license plate and type are recognized. The position of the vehicles is then tracked using the recognized license plate information and cameras mounted on each deck and ramp. Finally, once the vehicle stops, this information is transmitted to the loading computer. We applied the proposed method to RoPax vessels to evaluate their effectiveness. We modeled a total of two decks and loaded 60 vehicles to verify whether the positions of these vehicles were accurately received by the loading computer through interface. loading plan was then utilized to assess the ship's stability. This confirmed that the proposed method can be used to improve the accuracy of stability assessments by eliminating human error. As a result, more precise and reliable evaluations of a ship's stability can be achieved using proposed approach.
- Open Access
- 27 May 2024
- Published by TU Delft OPEN Publishing in International Marine Design Conference
The method to navigate the forward and backward path of a towing tractor for transporting aircraft
Aircraft carriers are the backbone of the Navy. They are equipped with aircraft, and their ability to take off and land aircraft quickly and efficiently determines their performance. Therefore, the number of aircraft is a key consideration in the design of an aircraft carrier and ensuring that they can be operated in the space of the aircraft carrier is an important factor in the arrangement design as well. On the other hands, towing tractors are used to move aircraft around. Towing tractors must safely move aircraft in open spaces while avoiding multiple obstacles, which requires skilled operators. In this study, we propose a method to automate the path of a towing tractor and then follow it. First, we studied the kinematics of the towing tractor and aircraft carrier, considering the wheel movement and steering angle. Then, we calculated the optimal path of the tractor and aircraft considering both forward and backward motion. Finally, we applied dynamics to verify that the towing tractor and aircraft carrier could follow the calculated path. We tested the proposed method in a field with various obstacles and in a narrow area such as a parking lot and confirmed that it was effective.
- 27 May 2024
- Published by TU Delft OPEN Publishing in International Marine Design Conference
Open AccessThe method to navigate the forward and backward path of a towing tractor for transporting aircraft
Aircraft carriers are the backbone of the Navy. They are equipped with aircraft, and their ability to take off and land aircraft quickly and efficiently determines their performance. Therefore, the number of aircraft is a key consideration in the design of an aircraft carrier and ensuring that they can be operated in the space of the aircraft carrier is an important factor in the arrangement design as well. On the other hands, towing tractors are used to move aircraft around. Towing tractors must safely move aircraft in open spaces while avoiding multiple obstacles, which requires skilled operators. In this study, we propose a method to automate the path of a towing tractor and then follow it. First, we studied the kinematics of the towing tractor and aircraft carrier, considering the wheel movement and steering angle. Then, we calculated the optimal path of the tractor and aircraft considering both forward and backward motion. Finally, we applied dynamics to verify that the towing tractor and aircraft carrier could follow the calculated path. We tested the proposed method in a field with various obstacles and in a narrow area such as a parking lot and confirmed that it was effective.
- Open Access
- 3 April 2023
- Published by American Association for Cancer Research (AACR)
Supplementary Methods, Supplementary Figures 1 to 9, and Supplementary Tables 1 to 3 from Enhancement of the Tumor Penetration of Monoclonal Antibody by Fusion of a Neuropilin-Targeting Peptide Improves the Antitumor Efficacy
- 3 April 2023
- Published by American Association for Cancer Research (AACR)
Open AccessSupplementary Methods, Supplementary Figures 1 to 9, and Supplementary Tables 1 to 3 from Enhancement of the Tumor Penetration of Monoclonal Antibody by Fusion of a Neuropilin-Targeting Peptide Improves the Antitumor Efficacy
- Open Access
- 16 October 2020
- Published by MDPI AG in Journal of Marine Science and Engineering
- Vol. 8 (10) , 805
Prediction of Ocean Weather Based on Denoising AutoEncoder and Convolutional LSTM
The path planning of a ship requires much information, and one of the essential factors is predicting the ocean environment. Ocean weather can generally be gathered from forecasting information provided by weather centers. However, these data are difficult to obtain when satellite communication is unstable during voyages, or there are cases where forecast data for a more extended period of time are needed for the operation of the fleet. Therefore, shipping companies and classification societies have attempted to establish a model for predicting the ocean weather on its own. Historically, ocean weather has been primarily predicted using empirical and numerical methods. Recently, a method for predicting ocean weather using deep learning has emerged. In this study, a deep learning model combining a denoising AutoEncoder and convolutional long short-term memory (LSTM) was proposed to predict the ocean weather worldwide. The denoising AutoEncoder is effective for removing noise that hinders the training of deep learning models. While the LSTM could be used as time-series inputs at specific points, the convolutional LSTM can use time-series images as inputs, making them suitable for predicting a wide range of ocean weather. Herein, using the proposed model, eight parameters of ocean weather were predicted. The proposed learning model predicted ocean weather after one week, showing an average error of 6.7%. The results show the applicability of the proposed learning model for predicting ocean weather.
- 16 October 2020
- Published by MDPI AG in Journal of Marine Science and Engineering
- Vol. 8 (10) , 805
Open AccessPrediction of Ocean Weather Based on Denoising AutoEncoder and Convolutional LSTM
The path planning of a ship requires much information, and one of the essential factors is predicting the ocean environment. Ocean weather can generally be gathered from forecasting information provided by weather centers. However, these data are difficult to obtain when satellite communication is unstable during voyages, or there are cases where forecast data for a more extended period of time are needed for the operation of the fleet. Therefore, shipping companies and classification societies have attempted to establish a model for predicting the ocean weather on its own. Historically, ocean weather has been primarily predicted using empirical and numerical methods. Recently, a method for predicting ocean weather using deep learning has emerged. In this study, a deep learning model combining a denoising AutoEncoder and convolutional long short-term memory (LSTM) was proposed to predict the ocean weather worldwide. The denoising AutoEncoder is effective for removing noise that hinders the training of deep learning models. While the LSTM could be used as time-series inputs at specific points, the convolutional LSTM can use time-series images as inputs, making them suitable for predicting a wide range of ocean weather. Herein, using the proposed model, eight parameters of ocean weather were predicted. The proposed learning model predicted ocean weather after one week, showing an average error of 6.7%. The results show the applicability of the proposed learning model for predicting ocean weather.
- Open Access
- 12 October 2020
- Published by MDPI AG in Journal of Marine Science and Engineering
- Vol. 8 (10) , 791
ISO 15016:2015-Based Method for Estimating the Fuel Oil Consumption of a Ship
Recently, interest in the design and construction of smart ships has been widely increasing. Optimal route planning is a widely studied essential aspect of smart ship technology. Planning an optimal route requires an accurate estimation of the fuel oil consumption of a ship. Various studies have suggested methods for theoretically estimating the fuel oil consumption. However, the calculation methodology and accuracy are different for each method. In addition, in commercial software, a statistical model based mainly on operating data has been used. Therefore, in this study, we propose a method based on ISO 15016:2015 for estimating the fuel oil consumption of a ship by improving the ISO 15016:2002 method—which has been predominantly used in existing studies. Moreover, the accuracy of the proposed method is examined by comparing it with a gray box model based on operating data. The results confirm that the proposed method can be used for estimating the fuel oil consumption of a ship.
- 12 October 2020
- Published by MDPI AG in Journal of Marine Science and Engineering
- Vol. 8 (10) , 791
Open AccessISO 15016:2015-Based Method for Estimating the Fuel Oil Consumption of a Ship
Recently, interest in the design and construction of smart ships has been widely increasing. Optimal route planning is a widely studied essential aspect of smart ship technology. Planning an optimal route requires an accurate estimation of the fuel oil consumption of a ship. Various studies have suggested methods for theoretically estimating the fuel oil consumption. However, the calculation methodology and accuracy are different for each method. In addition, in commercial software, a statistical model based mainly on operating data has been used. Therefore, in this study, we propose a method based on ISO 15016:2015 for estimating the fuel oil consumption of a ship by improving the ISO 15016:2002 method—which has been predominantly used in existing studies. Moreover, the accuracy of the proposed method is examined by comparing it with a gray box model based on operating data. The results confirm that the proposed method can be used for estimating the fuel oil consumption of a ship.
- 4 October 2020
- Published by Springer Nature
- p. 190-197
Optimal Arrangement Method of a Ship Considering the Performance Against Flooding
- 4 October 2020
- Published by Springer Nature
- p. 190-197
Optimal Arrangement Method of a Ship Considering the Performance Against Flooding
- 24 February 2020
- Published by ASME International in Journal of Offshore Mechanics and Arctic Engineering
- Vol. 142 (4) , 1-56
Optimal Layout Design of a Liquefied Natural Gas FPSO: A Case Study
An liquefied natural gas (LNG) FPSO is a floating, production, storage, and offloading facility with a LNG plant, including all ancillary facilities. In contrast to commercial vessels, the various parts of the process are located topside and are distributed as modules that are installed on the deck. The design of an LNG FPSO requires many considerations such as international codes and standards, the owner's requirements, and the operation and maintenance philosophy. To resolve the many considerations in FPSO design, we proposed an optimization method for the topside arrangement in the previous study. Based on the previous study, an integrated optimization technique for an LNG FPSO is proposed to obtain the optimal principle dimensions, the arrangement of the hull tanks, and the layout of the topside modules and equipment that satisfies many requirements for not only the topside but also the hull. As a case study, the topside and hull layout of an LNG FPSO is optimized in terms of safety, economics, and stability. The case study shows that the proposed method can develop the optimal layout design of an LNG FPSO.
- 24 February 2020
- Published by ASME International in Journal of Offshore Mechanics and Arctic Engineering
- Vol. 142 (4) , 1-56
Optimal Layout Design of a Liquefied Natural Gas FPSO: A Case Study
An liquefied natural gas (LNG) FPSO is a floating, production, storage, and offloading facility with a LNG plant, including all ancillary facilities. In contrast to commercial vessels, the various parts of the process are located topside and are distributed as modules that are installed on the deck. The design of an LNG FPSO requires many considerations such as international codes and standards, the owner's requirements, and the operation and maintenance philosophy. To resolve the many considerations in FPSO design, we proposed an optimization method for the topside arrangement in the previous study. Based on the previous study, an integrated optimization technique for an LNG FPSO is proposed to obtain the optimal principle dimensions, the arrangement of the hull tanks, and the layout of the topside modules and equipment that satisfies many requirements for not only the topside but also the hull. As a case study, the topside and hull layout of an LNG FPSO is optimized in terms of safety, economics, and stability. The case study shows that the proposed method can develop the optimal layout design of an LNG FPSO.
- 4 October 2017
- Published by ASME International in Journal of Offshore Mechanics and Arctic Engineering
- Vol. 140 (1) , 014501
Weight-Estimation Method of FPSO Topsides Considering the Work Breakdown Structure
With the recent international economic downturn, most engineering, procurement, and construction (EPC) contractors are incurring deficits in their floating, production, storage, and offloading unit (FPSO) projects. Numerous reasons underpin these situations. One of the most important reasons is the cost-estimation failure. The cost estimation is the key contractual point and mainly depends on a weight estimation of the FPSO topsides. Because the topsides contain a lot of equipment and complex structures, it is very difficult to make an estimation at the contractual stage. To overcome this problem, many methods have been proposed to estimate the weight of offshore topsides; however, most of the methods involve the top–down approach, making it difficult to obtain a sufficiently accurate prediction for field-work usage in terms of the weight estimation. Therefore, a work breakdown structure (WBS) for the performance of the weight-estimation process is proposed in this study. Using the WBS of the FPSO topsides, the corresponding presentation of the weight-estimation process makes the process usable in the field work regarding the WBS-item estimations. Accordingly, estimates of the detailed units (disciplines, modules, and areas) inside the topside that were previously not possible were performed. In addition, a prototype program was developed using the proposed method, and the applicability of the proposed method was evaluated through the application of three projects.
- 4 October 2017
- Published by ASME International in Journal of Offshore Mechanics and Arctic Engineering
- Vol. 140 (1) , 014501
Weight-Estimation Method of FPSO Topsides Considering the Work Breakdown Structure
With the recent international economic downturn, most engineering, procurement, and construction (EPC) contractors are incurring deficits in their floating, production, storage, and offloading unit (FPSO) projects. Numerous reasons underpin these situations. One of the most important reasons is the cost-estimation failure. The cost estimation is the key contractual point and mainly depends on a weight estimation of the FPSO topsides. Because the topsides contain a lot of equipment and complex structures, it is very difficult to make an estimation at the contractual stage. To overcome this problem, many methods have been proposed to estimate the weight of offshore topsides; however, most of the methods involve the top–down approach, making it difficult to obtain a sufficiently accurate prediction for field-work usage in terms of the weight estimation. Therefore, a work breakdown structure (WBS) for the performance of the weight-estimation process is proposed in this study. Using the WBS of the FPSO topsides, the corresponding presentation of the weight-estimation process makes the process usable in the field work regarding the WBS-item estimations. Accordingly, estimates of the detailed units (disciplines, modules, and areas) inside the topside that were previously not possible were performed. In addition, a prototype program was developed using the proposed method, and the applicability of the proposed method was evaluated through the application of three projects.
- Open Access
- 3 April 2017
- Published by Association for Computing Machinery (ACM)
- p. 1563-1565
DACS
Virtual machines are used in various fields to increase the resource utilization. In a virtual machine monitor, I/O requests are the most frequent tasks for virtual machines. However, a virtual machine monitor cannot guarantee I/O responsiveness when multiple tasks are being performed on virtual machines. We propose a scheduling scheme that provides fast I/O responsiveness for virtual machines. The proposed scheme provides high resource utilization by dynamically allocating virtual resources to virtual machines according to the characteristics of their tasks. In experiments with virtual machines containing varying task characteristics, it is shown that the proposed scheme provides improved I/O responsiveness when compared to existing virtual machine schedulers.
- 3 April 2017
- Published by Association for Computing Machinery (ACM)
- p. 1563-1565
Open AccessDACS
Virtual machines are used in various fields to increase the resource utilization. In a virtual machine monitor, I/O requests are the most frequent tasks for virtual machines. However, a virtual machine monitor cannot guarantee I/O responsiveness when multiple tasks are being performed on virtual machines. We propose a scheduling scheme that provides fast I/O responsiveness for virtual machines. The proposed scheme provides high resource utilization by dynamically allocating virtual resources to virtual machines according to the characteristics of their tasks. In experiments with virtual machines containing varying task characteristics, it is shown that the proposed scheme provides improved I/O responsiveness when compared to existing virtual machine schedulers.