VMVladimir I. Melikhov

Vladimir I. Melikhov

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Vladimir I. Melikhov has a total of 32 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Numerical simulation study of parametric effects on thermal stratification characteristics in the TALL-3D test section

    by Tianxin Song, Li Li, Songbai Cheng, Haonan Zhang, Vladimir I. Melikhov, Oleg I. Melikhov

    Lead-cooled fast reactor (LFR) is a promising Generation IV nuclear system with favorable thermal efficiency and inherent safety advantages. The pool-type design simplifies the LFR system and enhances its inherent safety characteristics. However, pool-type LFR may experience pronounced thermal stratification during transients such as pump trip and loss of forced circulation, as reduced coolant momentum weakens mixing and promotes the separation of hot and cold coolant. The resulting significant temperature gradients may adversely affect natural circulation heat removal and structural integrity. Presently, systematic studies on LFR thermal stratification remain limited worldwide; thus, further comprehensive investigations are needed for its evolution mechanisms, interface characteristics, and temperature-field structures. This study numerically investigates the key factors influencing thermal stratification through geometric modeling and simulation of TALL-3D experiment. Parametric-controlled simulations were performed to evaluate the effects of inlet conditions, system thermal balance parameters, and inner plate configurations on temperature distribution, vertical temperature gradient, and stratification structure. The results show that thermal stratification is governed by the coupled effects of momentum transport, thermal balance, and internal flow structures. Among the investigated parameters, inlet mass flow rate and rope heater power exhibit pronounced influences on thermal stratification by modifying the inlet jet momentum and the system heat input. Higher inlet mass flow rates and wall heat losses tend to mitigate thermal stratification, whereas inlet temperature and turbulence intensity have limited effects on the overall stratification structure. The inner plate elevation mainly affects local temperature gradients by modifying the deflection and spreading behavior of the inlet jet. Comparison with scaling analysis confirms that the stratification criterion consistently exceeds the calibrated threshold for the TALL-3D geometry across all parametric cases, indicating that the inlet jet momentum is insufficient to overcome buoyancy forces and that a self-similar compensation mechanism maintains stratification stability despite variations in flow rate and heating power. These results provide further understanding for the behavior of TALL-3D thermal stratification and support the development of LFR technology.

  • Open Access

    An experimental and computational study of the operation of passive safety systems under design extension conditions in a Generation III+ VVER

    by Andrey V. Kapustin, Kirill S. Dolganov, Dmitry Yu. Tomashchik, O.I. Melikhov, Vladimir I. Melikhov, Sergey M. Nikonov

    This paper addresses the assessment of integral computer codes used to verify the effectiveness of the Generation III+ VVERs passive safety systems designed to provide the long-term residual heat removal in the event of a loss-of-coolant accident (LOCA) concurrent with a station blackout (SBO). In particular, it discusses the suitability of experimental data for code validation, as well as the uncertainties arising from experimental data and propagating to deterministic safety analyses of nuclear power plants. Given the overall complexity of the topic, the paper has been compiled to achieve three objectives: (1) to identify important thermal-hydraulic phenomena and integral system effects relevant to the long-term residual heat removal with the passive safety systems in VVER-TOI reactor; (2) to analyze an integral effects test (IET) specifically designed for the assessment of the VVER-TOI passive safety systems; and (3) to estimate the associated modeling uncertainties that can influence the prediction of the real plant behavior. The PSB-VVER CL-0.58-02 test has been selected as an IET representative of the expected VVER-TOI behavior during a DEC initiated by a combination of a loss-of-coolant accident (LOCA) and a prolonged station blackout. The integral code SOCRAT has been used to analyze the experimental data and to assess the suitability of experimental data for code validation.

  • Horizontal Steam Generators: Design Improvement and Experimental-and-Computational Studies (Review)

    by V. N. Blinkov, A. V. Dedov, I. V. Elkin, V. I. Melikhov, O. I. Melikhov, S. M. Nikonov, A. S. Nikulin

    A review is presented of designs of horizontal steam generators (SG) for nuclear power plants (NPP) with water-moderated water-cooled reactors (VVERs) and of experimental-and-computational studies of thermohydraulic processes running in them. Horizontal SGs are examined from the first commercial design of the PGV-440 SG and the most widely used today PGV-1000M SG to the steam generators developed for the new generation reactor units of types VVER-1200 and VVER-TOI as well as for the high-power VVER-1500 reactor. A comparative analysis was carried out of the experimental facilities developed for the investigation of thermohydraulic processes occurring in a horizontal steam generator. Each of the examined experimental facilities has limitation related to the capabilities for the simulation of a full-scale SG caused by either geometric characteristics or thermohydraulic conditions. Nevertheless, it has been demonstrated that we have at present a sufficiently large experimental database suitable for validating computational codes simulating thermohydraulic characteristics of a horizontal steam generator. A review of the available computational codes is presented. The STEG code in which the two-phase flow is described by multifluid models is examined in more detail. The validation of the STEG code against experimental data on void fraction, pressure drop, and water velocity demonstrated high accuracy of the predictions. One of the problems to be solved in designing horizontal steam generators for new generation reactor units is the improvement of the equalization ability of the submerged and steam-receiving perforated sheets due to the enhanced nonuniformity of the steam load on the evaporation surface and of the steam flow in the steam space. The results are presented of the experimental-and-computational investigation of the equalization ability of perforated sheets, which corroborate the possibility of its improvement by application of a variable perforation ratio. The areas of further experimental investigations into thermohydraulic processes in a horizontal steam generator and ideas for improving the computational codes are formulated.


  • Validating the OpenFOAM Code against the Experimental Data on Coolant Mixing in a Reactor Model

    by Урегани Наджмех [Uregani Nadzmeh] Джафари [Jafari], Хоссейн [Hosseyn] Абди [Abdi], Сергей [Sergey] Михайлович [M.] Никонов [Nikonov], Владимир [Vladimir] Игорьевич [I.] Мелихов [Melikhov], Олег [Oleg] Игорьевич [I.] Мелихов [Melikhov], Александр [Aleksandr] Александрович [A.] Шпаковский [Shpakovsky]

    The purpose of the study is to simulate experiments on mixing water supplied from a hydro accumulator for cooling the reactor core with the coolant in the downcomer section using the OpenFOAM computer code. The OpenFOAM code is a freely released open source software program used for solving a variety of problems, including heat transfer and fluid dynamics. To validate the OpenFOAM code, experimental data from the downcomer test facility (DTF) were used. The DFT was specially constructed to simulate the mixing of the emergency core cooling system (ECCS) water with the coolant in the reactor downcomer, as well as the thermal effect this water has on the vessel walls. The DTF test section consists of a vertical cylindrical atmospheric tank. The test section is connected to the hydro accumulator’s DN32 circulation pipeline and DN20 drain pipeline. The circulation pipeline serves to set up a flow of cold or hot water through the test section. The hydro accumulator simulates the reactor plant’s ECCS hydro accumulator. The process of mixing cold and hot fluids was recorded using around a hundred thermocouples installed in the ECCS water supply zone on the test section surface in the downcomer, as well as on the baffle surface. Two experiments, No. 1 and No. 15, were selected to validate the OpenFOAM code. In experiment No. 1, hot water with a temperature of 349 K was fed from the hydro accumulator to the cold water volume (283–293 K) in the test section. In experiment No. 15, an inverse scenario was simulated: cold water (290 K) was supplied from the hydro accumulator to the hot water volume (333–343 K) in the test section. A computational mesh was generated, which included around 2 million cells. The turbulence was described by means of the k–e turbulence model. In view of an uncertainty of the heat transfer parameters between the vessel and surrounding air, two heat transfer coefficient values were selected: 5 and 10 W/(m2 K). The calculation results have demonstrated that the OpenFOAM algorithm can adequately simulate the processes of non-isothermal mixing of the hydro accumulator water with the coolant. The standard deviations of the predicted temperature values from the experimental data do not exceed 2.1 K, while the experimental error in temperature measurement is ±3 K. Цель работы состоит в моделировании экспериментов по перемешиванию воды, подаваемой из гидроемкости для охлаждения активной зоны реактора, с теплоносителем в опускном участке с помощью расчетного кода OpenFOAM. Код OpenFOAM — свободно распространяемый продукт с открытыми исходными текстами программ, предназначенный для решения различных задач, включающих в себя теплообмен и гидродинамику. Для валидации кода OpenFOAM использованы экспериментальные данные, полученные на установке СОУ, созданной для моделирования перемешивания охлаждающей воды системы аварийного охлаждения активной зоны (САОЗ) с теплоносителем в опускном участке реактора и её термического воздействия на стенки корпуса. Рабочий участок установки СОУ (стенд–опускной участок) представляет собой вертикальную цилиндрическую емкость атмосферного типа. К рабочему участку присоединены циркуляционный Ду32 и сливной Ду20 трубопроводы гидроемкости. Циркуляционный трубопровод служит для создания потока холодной или горячей воды через рабочий участок. Гидроемкость имитирует гидроемкость САОЗ реакторной установки. Процесс перемешивания холодной и горячей жидкостей регистрируется с помощью примерно сотни термопар, расположенных в зоне подачи воды САОЗ на поверхности рабочего участка в опускном участке и на поверхности выгородки. Для валидации кода OpenFOAM выбраны два эксперимента — №№ 1 и 15. В эксперименте № 1 горячую воду температурой 349 K подавали из гидроемкости в объем холодной воды (283…293 K) в рабочем участке. Обратная ситуация моделировалась в эксперименте № 15, а именно, холодную воду 290 K направляли из гидроемкости в объем горячей воды (333…343 K) в рабочем участке. Была создана расчетная сетка, включающая в себя около 2 млн ячеек. Для описания турбулентности использована k-ε модель турбулентности. Ввиду неопределенности параметров теплообмена корпуса сосуда с окружающим воздухом взяты два значения коэффициента теплоотдачи 5 и 10 Вт/(м2∙K). Проведенные расчеты показали адекватную способность кода OpenFOAM моделировать...

  • Validation of the STEG Code against Experimental Data on Hydrodynamics of a Horizontal Steam Generator

    by H. Abdi, N. Ouregani Jafari, V. I. Melikhov, O. I. Melikhov

    A numerical analysis of the experiments addressed to studies of hydrodynamic processes in a horizontal steam generator has been performed using the STEG (STEam Generator) code. The main components of the experimental model include a staggered tube bundle, a submerged perforated sheet (SPS) with baffles, and a downcomer. An air–water mixture was used as a two-phase fluid. The working fluid flow in the model was driven by natural circulation induced by air supply to the lower, middle, and upper sections of the tube bundle. The gas void fraction was measured by the γ-radiography method. In addition, pressure drops along the height of the tube bundle and water levels in the model and above SPS were also measured. Each experiment was performed at a prescribed air load on the evaporation surface and water level in the model. The STEG code was developed at the Department of Nuclear Power Plants of NRU MPEI to model thermohydraulic processes in a horizontal steam generator. The mathematical model is based on a two-fluid approach to the description of a two-phase flow using balance mass, momentum, and energy conservation equations and semiempirical closing correlations for interfacial interactions and interactions with various surrounding structures (tube bundle, walls, etc.). The STEG code was used to perform calculations for nine experimental regimes differing in the perforation ratio of the submerged perforated sheet and the supplied air flowrate. The qualitative regularities of the two-phase air–water mixture circulation in the model of a horizontal steam generator and the effect of experimental values of the main parameters on the circulation have been established. Quantitative results of comparison of the predictions with the experiment demonstrate their good agreement since the relative errors in the predicted air void fractions and pressure drops do not exceed 10%.


  • Open Access

    Numerical Modeling of Water Jet Plunging in Molten Heavy Metal Pool

    by Sergey E. Yakush, Nikita S. Sivakov, Oleg I. Melikhov, Vladimir I. Melikhov

    The hydrodynamic and thermal interaction of water with the high-temperature melt of a heavy metal was studied via the Volume-of-Fluid (VOF) method formulated for three immiscible phases (liquid melt, water, and water vapor), with account for phase changes. The VOF method relies on a first-principle description of phase interactions, including drag, heat transfer, and water evaporation, in contrast to multifluid models relying on empirical correlations. The verification of the VOF model implemented in OpenFOAM software was performed by solving one- and two-dimensional reference problems. Water jet penetration into a melt pool was first calculated in two-dimensional problem formulation, and the results were compared with analytical models and empirical correlations available, with emphasis on the effects of jet velocity and diameter. Three-dimensional simulations were performed in geometry, corresponding to known experiments performed in a narrow planar vessel with a semi-circular bottom. The VOF results obtained for water jet impact on molten heavy metal (lead–bismuth eutectic alloy at the temperature 820 K) are here presented for a water temperature of 298 K, jet diameter 6 mm, and jet velocity 6.2 m/s. Development of a cavity filled with a three-phase melt–water–vapor mixture is revealed, including its propagation down to the vessel bottom, with lateral displacement of melt, and subsequent detachment from the bottom due to gravitational settling of melt. The best agreement of predicted cavity depth, velocity, and aspect ratio with experiments (within 10%) was achieved at the stage of downward cavity propagation; at the later stages, the differences increased to about 30%. Adequacy of the numerical mesh containing about 5.6 million cells was demonstrated by comparing the penetration dynamics obtained on a sequence of meshes with the cell size ranging from 180 to 350 µm.


  • Study of a Thermal Detonation Wave in a Mixture of Water Droplets and Molten Lead

    by V. I. Melikhov, O. I. Melikhov, S. Bashar

    The regularities of the wave of the thermal interaction of water drops in high-temperature molten lead, i.e., a thermal-detonation wave, are studied. Due to the boiling of water on the surface of molten lead, both liquids (phases) are separated by a vapor film. A one-dimensional model of interacting and interpenetrating continua is used, which describes the dynamics of each fluid by introducing a special field characterized by its own velocity, temperature, and volume fraction. The wave velocity is set by the equality of phase velocities and temperatures in the Chapman–Jouguet plane. The parameters at the pressure peak are calculated from the conditions at the discontinuity which are the boundary conditions for integrating the conservation equations in the area of interaction between water droplets and the melt. The resulting structure of the thermal-detonation wave is characterized by the maximum pressure being located at some distance from the shock wave.

  • Investigation of a Thermal Detonation Wave in a Mixture of Water Drops with Molted Lead

    by V. I. Melikhov, O. I. Melikhov, Saleh Bashar

    Investigation of a Thermal Detonation Wave in a Mixture of Water Drops with Molted Lead Исследование волны термической детонации в смеси капель воды с расплавленным свинцом

  • Open Access

    Pressure Waves due to Rapid Evaporation of Water Droplet in Liquid Lead Coolant

    by S. E. Yakush, A. S. Iskhakov, V. I. Melikhov, O. I. Melikhov

    Flash evaporation of a superheated water droplet in heavy liquid metal coolant (lead) is considered, in application to the analysis of a lead-cooled fast reactor steam generator tube rupture accident. The model is based on thermodynamic equilibrium formulation for the expanding water-steam mixture and inviscid compressible formulation for the surrounding liquid lead, with the interface conditions determined from the solution of the Riemann problem. Numerical solution is performed in the spherically symmetric geometry using a conservative numerical scheme with a moving sharp interface. Transient pressure and velocity profiles in each phase are presented for the parameters typical of the steam generator tube rupture accidents, demonstrating the process of boiling water expansion and pressure wave formation in the coolant. The results obtained are compared with a simplified model which considers the volume-averaged parameters of boiling water droplets and considers coolant as an incompressible liquid. Good agreement between the full and simplified models is demonstrated. Impacts of coolant flow on structures caused by pressure wave propagation and subsequent coolant flow are discussed.


  • Open Access

    Experimental Studies for the VVER-440/213 Bubble Condenser System for Kola NPP at the Integral Test Facility BC V-213

    by Vladimir N. Blinkov, Oleg I. Melikhov, Vladimir I. Melikhov, Mikhail V. Davydov, Holger Wolff, Siegfried Arndt

    In the frame of Tacis Project R2.01/99, which was running from 2003 to 2005, the bubble condenser system of Kola NPP (unit 3) was qualified at the integral test facility BC V-213. Three LB LOCA tests, two MSLB tests, and one SB LOCA test were performed. The appropriate test scenarios for BC V-213 test facility, modeling accidents in the Kola NPP unit 3, were determined with pretest calculations. Analysis of test results has shown that calculated initial conditions and test scenarios were properly reproduced in the tests. The detailed posttest analysis of the tests performed at BC V-213 test facility was aimed to validate the COCOSYS code for the calculation of thermohydraulic processes in the hermetic compartments and bubble condenser. After that the validated COCOSYS code was applied to NPP calculations for Kola NPP (unit 3). Results of Tacis R2.01/99 Project confirmed the bubble condenser functionality during large and small break LOCAs and MSLB accidents. Maximum loads were reached in the LB LOCA case. No condensation oscillations were observed.