Xiang Chen
Research Subjects
Xiang Chen has a total of 58 co-authors. Here are the top co-authors by number of shared publications:
- Zhifeng Hao
Shantou University
16 shared publications Jian Yu
10 shared publicationsMohamed S. Selim
Key Laboratory of Clean Chemistry Technology of Guangdong Regular Higher Education Institutions, School of Chemical Engineering and Light Industry
10 shared publicationsJunlin Chen
4 shared publicationsYuanzhou Chen
4 shared publicationsGuizhen Tan
3 shared publications
Latest Publications
- 10 February 2026
- Published by American Chemical Society (ACS) in ACS Applied Bio Materials
- Vol. 9 (5) , 2698-2711
Broad-Spectrum Light-Activated Synergistic Antibacterial Platform Based on an Azobenzene–Quaternary Ammonium@MXene Nanocomposite
To address the global public health challenge of bacterial infections, this study developed a broadband-responsive nanoantibacterial composite material named TAB AZO-GA-MXene (TAGM). The material was prepared by electrostatically loading cationic azobenzene quaternary ammonium salts onto the surface of the two-dimensional nanomaterial MXene, with gum Arabic (GA) used as a dispersant. The antibacterial properties of the composite material exhibit distinct variations following irradiation across a broad spectrum of light, including ultraviolet, visible, and near-infrared wavelengths. TAGM combines the physical shearing and photothermal effects of MXene with the membrane-disrupting and DNA-damaging capabilities of azobenzene quaternary ammonium salts, thereby establishing a multimechanism synergistic antibacterial platform. Experimental results show that the Trans form of TAGM demonstrates stronger bactericidal activity against E. coli under green light, whereas the Cis form exhibits better inhibitory activity against S. aureus under ultraviolet light. Under corresponding illumination conditions, TAGM achieved bacterial inactivation rates of 99.11% against E. coli and 99.81% against S. aureus, indicating rapid and highly efficient antimicrobial performance. This study not only broadens the spectral response range of light-responsive antibacterial materials but also provides a strategy for developing selective, multimechanism synergistic antibacterial systems, showing promising potential for combating multidrug-resistant bacterial infections.
- 10 February 2026
- Published by American Chemical Society (ACS) in ACS Applied Bio Materials
- Vol. 9 (5) , 2698-2711
Broad-Spectrum Light-Activated Synergistic Antibacterial Platform Based on an Azobenzene–Quaternary Ammonium@MXene Nanocomposite
To address the global public health challenge of bacterial infections, this study developed a broadband-responsive nanoantibacterial composite material named TAB AZO-GA-MXene (TAGM). The material was prepared by electrostatically loading cationic azobenzene quaternary ammonium salts onto the surface of the two-dimensional nanomaterial MXene, with gum Arabic (GA) used as a dispersant. The antibacterial properties of the composite material exhibit distinct variations following irradiation across a broad spectrum of light, including ultraviolet, visible, and near-infrared wavelengths. TAGM combines the physical shearing and photothermal effects of MXene with the membrane-disrupting and DNA-damaging capabilities of azobenzene quaternary ammonium salts, thereby establishing a multimechanism synergistic antibacterial platform. Experimental results show that the Trans form of TAGM demonstrates stronger bactericidal activity against E. coli under green light, whereas the Cis form exhibits better inhibitory activity against S. aureus under ultraviolet light. Under corresponding illumination conditions, TAGM achieved bacterial inactivation rates of 99.11% against E. coli and 99.81% against S. aureus, indicating rapid and highly efficient antimicrobial performance. This study not only broadens the spectral response range of light-responsive antibacterial materials but also provides a strategy for developing selective, multimechanism synergistic antibacterial systems, showing promising potential for combating multidrug-resistant bacterial infections.
- 17 September 2025
- Published by American Chemical Society (ACS) in ACS Applied Bio Materials
- Vol. 8 (10) , 9229-9244
Multifunctional Chitosan Hydrogel Integrated with Penicillin-Grafted MXene for Synergistic Antibacterial Application
Hydrogels have received significant attention in the biomedical field, but traditional antibacterial hydrogels have certain limitations in terms of antibacterial activity, resistance, and functionality. In this study, we present a multifunctional hydrogel synthesized through a one-step process using carboxymethyl chitosan (CMCS) as the matrix, tannic acid (TA) as the cross-linking agent, and penicillin (PG)-loaded MXene as the drug additive, for antibacterial therapy. In this system, the composite hydrogel is physically cross-linked through ionic bonds and hydrogen bonds between CMCS and TA, exhibiting good injectability, self-healing properties, and tissue adhesiveness. The incorporation of MXene drug-loaded with penicillin imparts photothermal properties to the hydrogel, thereby enabling a synergistic antibacterial effect between the components, resulting in stable antibacterial activity. In addition, the hydrogel exhibits favorable biocompatibility, as well as the capacity to scavenge reactive oxygen species (ROS) and rapidly arrest hemorrhaging, showing promising applications in wound care.
- 17 September 2025
- Published by American Chemical Society (ACS) in ACS Applied Bio Materials
- Vol. 8 (10) , 9229-9244
Multifunctional Chitosan Hydrogel Integrated with Penicillin-Grafted MXene for Synergistic Antibacterial Application
Hydrogels have received significant attention in the biomedical field, but traditional antibacterial hydrogels have certain limitations in terms of antibacterial activity, resistance, and functionality. In this study, we present a multifunctional hydrogel synthesized through a one-step process using carboxymethyl chitosan (CMCS) as the matrix, tannic acid (TA) as the cross-linking agent, and penicillin (PG)-loaded MXene as the drug additive, for antibacterial therapy. In this system, the composite hydrogel is physically cross-linked through ionic bonds and hydrogen bonds between CMCS and TA, exhibiting good injectability, self-healing properties, and tissue adhesiveness. The incorporation of MXene drug-loaded with penicillin imparts photothermal properties to the hydrogel, thereby enabling a synergistic antibacterial effect between the components, resulting in stable antibacterial activity. In addition, the hydrogel exhibits favorable biocompatibility, as well as the capacity to scavenge reactive oxygen species (ROS) and rapidly arrest hemorrhaging, showing promising applications in wound care.
- 6 August 2024
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 141 (42)
Self‐healing, low oil leakage and recyclable thermally conductive Al2O3/boron nitride@siloxane composites based on reversible dynamic network
In order to overcome the commercialized silicone‐based thermal interface materials' issues such as oil leakage and mechanical damage, we developed a thermoset silicone rubber matrix (SR) achieved through the condensation reaction of hydroxyl silicone oil and tetraethyl silicate. Additionally, we constructed a self‐healing and recyclable silicone rubber matrix (SCNR) by incorporating heat reversible ionic and hydrogen bonds between carboxyl and amino functionalized polydimethylsiloxane. Finally, the flexible, low oil leakage, self‐healing, and recyclable composites Al2O3/BN@SR/SCNR was prepared by adjusting the ratio of SR/SCNR and the spherical alumina and boron nitride (BN) fillers. The results indicated that with SR/SCNR mass ratio of 1/0.075 and filler content of 70 wt%, the thermal conductivity of the composite reaches 1.866 W m−1 K−1, 646% increasing over the SR/SCNR matrix. The self‐healing efficiency reaches 97% and the thermal conductivity remains essentially unchanged after being recycled for three times. The composites can be bent and twisted multiple times and still return to their original shape. Notably, the oil leakage of the Al2O3/BN@SR/SCNR composites is significantly lower than that of additive silicone composites. Therefore, the recyclable thermal conductivity composite developed in this study provides a promising solution for improving the durability of heat dissipation materials in electronic devices.
- 6 August 2024
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 141 (42)
Self‐healing, low oil leakage and recyclable thermally conductive Al2O3/boron nitride@siloxane composites based on reversible dynamic network
In order to overcome the commercialized silicone‐based thermal interface materials' issues such as oil leakage and mechanical damage, we developed a thermoset silicone rubber matrix (SR) achieved through the condensation reaction of hydroxyl silicone oil and tetraethyl silicate. Additionally, we constructed a self‐healing and recyclable silicone rubber matrix (SCNR) by incorporating heat reversible ionic and hydrogen bonds between carboxyl and amino functionalized polydimethylsiloxane. Finally, the flexible, low oil leakage, self‐healing, and recyclable composites Al2O3/BN@SR/SCNR was prepared by adjusting the ratio of SR/SCNR and the spherical alumina and boron nitride (BN) fillers. The results indicated that with SR/SCNR mass ratio of 1/0.075 and filler content of 70 wt%, the thermal conductivity of the composite reaches 1.866 W m−1 K−1, 646% increasing over the SR/SCNR matrix. The self‐healing efficiency reaches 97% and the thermal conductivity remains essentially unchanged after being recycled for three times. The composites can be bent and twisted multiple times and still return to their original shape. Notably, the oil leakage of the Al2O3/BN@SR/SCNR composites is significantly lower than that of additive silicone composites. Therefore, the recyclable thermal conductivity composite developed in this study provides a promising solution for improving the durability of heat dissipation materials in electronic devices.
- 18 July 2024
- Published by American Chemical Society (ACS) in ACS Applied Nano Materials
- Vol. 7 (14) , 16450-16465
A Triple-Functional Antibacterial Platform Based on Quaternized Ru(II) Complex-Loaded MXene Composites
- 18 July 2024
- Published by American Chemical Society (ACS) in ACS Applied Nano Materials
- Vol. 7 (14) , 16450-16465
A Triple-Functional Antibacterial Platform Based on Quaternized Ru(II) Complex-Loaded MXene Composites
- Top Cited Papers
- 9 May 2024
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 16 (20) , 26713-26732
Robust and Superhydrophobic Polydimethylsiloxane/Ni@Ti3C2Tx Nanocomposite Coatings with Assembled Eyelash-Like Microstructure Array: A New Approach for Effective Passive Anti-Icing and Active Photothermal Deicing
To solve the problem of ice condensation and adhesion, it is urgent to develop new anti-icing and deicing technologies. This study presented the development of a highly efficient photothermal-enhanced superhydrophobic PDMS/Ni@Ti3C2Tx composite film (m-NMPA) fabricated cost-effectively and straightforwardly. This film was fabricated utilizing PDMS as a hydrophobic agent, adhesive, and surface protector, while Ni@Ti3C2Tx as a magnetic photothermal filler innovatively. Through a simple spraying method, the filler is guided by a strong magnetic field to self-assemble into an eyelash-like microstructure array. The unique structure not only imparts superhydrophobic properties to the surface but also constructs an efficient "light-capturing" architecture. Remarkably, the m-NMPA film demonstrates outstanding superhydrophobic passive anti-icing and efficient photothermal active deicing performance without the use of fluorinated chemicals. The micro-/nanostructure of the film forms a gas layer, significantly delaying the freezing time of water. Particularly under extreme cold conditions (-30 °C), the freezing time is extended by a factor of 7.3 compared to the bare substrate. Furthermore, under sunlight exposure, surface droplets do not freeze. The excellent photothermal performance is attributed to the firm anchoring of nickel particles on the MXene surface, facilitating effective "point-to-face" photothermal synergy. The eyelash-like microarray structure enhances light-capturing capability, resulting in a high light absorption rate of 98%. Furthermore, the microstructure aids in maintaining heat at the uppermost layer of the surface, maximizing the utilization of thermal energy for ice melting and frost thawing. Under solar irradiation, the m-NMPA film can rapidly melt approximately a 4 mm thick ice layer within 558 s and expel the melted water promptly, reducing the risk of secondary icing. Additionally, the ice adhesion force on the surface of the m-NMPA film is remarkably low, with an adhesion strength of approximately 4.7 kPa for a 1 × 1 cm2 ice column. After undergoing rigorous durability tests, including xenon lamp weathering test, pressure resistance test, repeated adhesive tape testing, xenon lamp irradiation, water drop impact testing, and repeated brushing with hydrochloric acid and particles, the film's surface structure and superhydrophobic performance have remained exceptional. The photothermal superhydrophobic passive anti-icing and active deicing technology in this work rely on sustainable solar energy for efficient heat generation. It presents broad prospects for practical applications with advantages such as simple processing method, environmental friendliness, outstanding anti-icing effects, and exceptional durability.
- 9 May 2024
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 16 (20) , 26713-26732
Top Cited PapersRobust and Superhydrophobic Polydimethylsiloxane/Ni@Ti3C2Tx Nanocomposite Coatings with Assembled Eyelash-Like Microstructure Array: A New Approach for Effective Passive Anti-Icing and Active Photothermal Deicing
To solve the problem of ice condensation and adhesion, it is urgent to develop new anti-icing and deicing technologies. This study presented the development of a highly efficient photothermal-enhanced superhydrophobic PDMS/Ni@Ti3C2Tx composite film (m-NMPA) fabricated cost-effectively and straightforwardly. This film was fabricated utilizing PDMS as a hydrophobic agent, adhesive, and surface protector, while Ni@Ti3C2Tx as a magnetic photothermal filler innovatively. Through a simple spraying method, the filler is guided by a strong magnetic field to self-assemble into an eyelash-like microstructure array. The unique structure not only imparts superhydrophobic properties to the surface but also constructs an efficient "light-capturing" architecture. Remarkably, the m-NMPA film demonstrates outstanding superhydrophobic passive anti-icing and efficient photothermal active deicing performance without the use of fluorinated chemicals. The micro-/nanostructure of the film forms a gas layer, significantly delaying the freezing time of water. Particularly under extreme cold conditions (-30 °C), the freezing time is extended by a factor of 7.3 compared to the bare substrate. Furthermore, under sunlight exposure, surface droplets do not freeze. The excellent photothermal performance is attributed to the firm anchoring of nickel particles on the MXene surface, facilitating effective "point-to-face" photothermal synergy. The eyelash-like microarray structure enhances light-capturing capability, resulting in a high light absorption rate of 98%. Furthermore, the microstructure aids in maintaining heat at the uppermost layer of the surface, maximizing the utilization of thermal energy for ice melting and frost thawing. Under solar irradiation, the m-NMPA film can rapidly melt approximately a 4 mm thick ice layer within 558 s and expel the melted water promptly, reducing the risk of secondary icing. Additionally, the ice adhesion force on the surface of the m-NMPA film is remarkably low, with an adhesion strength of approximately 4.7 kPa for a 1 × 1 cm2 ice column. After undergoing rigorous durability tests, including xenon lamp weathering test, pressure resistance test, repeated adhesive tape testing, xenon lamp irradiation, water drop impact testing, and repeated brushing with hydrochloric acid and particles, the film's surface structure and superhydrophobic performance have remained exceptional. The photothermal superhydrophobic passive anti-icing and active deicing technology in this work rely on sustainable solar energy for efficient heat generation. It presents broad prospects for practical applications with advantages such as simple processing method, environmental friendliness, outstanding anti-icing effects, and exceptional durability.
- Open Access
- 7 March 2023
- Published by MDPI AG in Nanomaterials
- Vol. 13 (6) , 958
Ru(II) Complex Grafted Ti3C2Tx MXene Nano Sheet with Photothermal/Photodynamic Synergistic Antibacterial Activity
For a long time, the emergence of microbial drug resistance due to the abuse of antibiotics has greatly reduced the therapeutic effect of many existing antibiotics. This makes the development of new antimicrobial materials urgent. Light-assisted antimicrobial therapy is an alternative to antibiotic therapy due to its high antimicrobial efficiency and non-resistance. Here, we develop a nanocomposite material (Ru@MXene) which is based on Ru(bpy)(dcb)2+ connected to MXene nanosheets by ester bonding as a photothermal/photodynamic synergistic antibacterial material. The obtained Ru@MXene nanocomposites exhibit a strengthened antimicrobial capacity compared to Ru or MXene alone, which can be attributed to the higher reactive oxygen species (ROS) yield and the thermal effect. Once exposed to a xenon lamp, Ru@MXene promptly achieved almost 100% bactericidal activity against Escherichia coli (200 μg/mL) and Staphylococcus aureus (100 μg/mL). This is ascribed to its synergistic photothermal therapy (PTT) and photodynamic therapy (PDT) capabilities. Consequently, the innovative Ru@MXene can be a prospective non-drug antimicrobial therapy that avoids antibiotic resistance in practice. Notably, this high-efficiency PTT/PDT synergistic antimicrobial material by bonding Ru complexes to MXene is the first such reported model. However, the toxic effects of Ru@MXene materials need to be studied to evaluate them for further medical applications.
- 7 March 2023
- Published by MDPI AG in Nanomaterials
- Vol. 13 (6) , 958
Open AccessRu(II) Complex Grafted Ti3C2Tx MXene Nano Sheet with Photothermal/Photodynamic Synergistic Antibacterial Activity
For a long time, the emergence of microbial drug resistance due to the abuse of antibiotics has greatly reduced the therapeutic effect of many existing antibiotics. This makes the development of new antimicrobial materials urgent. Light-assisted antimicrobial therapy is an alternative to antibiotic therapy due to its high antimicrobial efficiency and non-resistance. Here, we develop a nanocomposite material (Ru@MXene) which is based on Ru(bpy)(dcb)2+ connected to MXene nanosheets by ester bonding as a photothermal/photodynamic synergistic antibacterial material. The obtained Ru@MXene nanocomposites exhibit a strengthened antimicrobial capacity compared to Ru or MXene alone, which can be attributed to the higher reactive oxygen species (ROS) yield and the thermal effect. Once exposed to a xenon lamp, Ru@MXene promptly achieved almost 100% bactericidal activity against Escherichia coli (200 μg/mL) and Staphylococcus aureus (100 μg/mL). This is ascribed to its synergistic photothermal therapy (PTT) and photodynamic therapy (PDT) capabilities. Consequently, the innovative Ru@MXene can be a prospective non-drug antimicrobial therapy that avoids antibiotic resistance in practice. Notably, this high-efficiency PTT/PDT synergistic antimicrobial material by bonding Ru complexes to MXene is the first such reported model. However, the toxic effects of Ru@MXene materials need to be studied to evaluate them for further medical applications.
- 1 November 2022
- Published by American Chemical Society (ACS) in ACS Applied Nano Materials
- Vol. 5 (11) , 16933-16941
Ti3C2Tx MXene Nanosheet-Based Probe for Ion Fluorescence and Visual Detection of Ag+ in Aqueous Solution and Living Cells
- 1 November 2022
- Published by American Chemical Society (ACS) in ACS Applied Nano Materials
- Vol. 5 (11) , 16933-16941
Ti3C2Tx MXene Nanosheet-Based Probe for Ion Fluorescence and Visual Detection of Ag+ in Aqueous Solution and Living Cells