Paria Karimi
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Paria Karimi has a total of 17 co-authors. Here are the top co-authors by number of shared publications:
- Joel Andersson
Department of Engineering Science, University West, Trollhättan, Sweden
6 shared publications - Esmaeil Sadeghi
University West
4 shared publications - Joakim Ålgårdh
University West
3 shared publications H. Gruber
University of Chalmers
2 shared publicationsAnders Eklund
1 shared publicationD. Deng
Linköping University
1 shared publication
Latest Publications
- 1 April 2019
- Published by Elsevier in Materials Characterization
- Vol. 150, 236-251
Influence of thermal post treatments on microstructure and oxidation behavior of EB-PBF manufactured Alloy 718
- 1 April 2019
- Published by Elsevier in Materials Characterization
- Vol. 150, 236-251
Influence of thermal post treatments on microstructure and oxidation behavior of EB-PBF manufactured Alloy 718
- 1 February 2019
- Published by Elsevier in Materials Characterization
- Vol. 148, 88-99
EBM-manufactured single tracks of Alloy 718: Influence of energy input and focus offset on geometrical and microstructural characteristics
- 1 February 2019
- Published by Elsevier in Materials Characterization
- Vol. 148, 88-99
EBM-manufactured single tracks of Alloy 718: Influence of energy input and focus offset on geometrical and microstructural characteristics
- Open Access
- 1 December 2018
- Published by Elsevier in Materials & Design
- Vol. 160, 427-441
Influence of successive thermal cycling on microstructure evolution of EBM-manufactured alloy 718 in track-by-track and layer-by-layer design
- 1 December 2018
- Published by Elsevier in Materials & Design
- Vol. 160, 427-441
Open AccessInfluence of successive thermal cycling on microstructure evolution of EBM-manufactured alloy 718 in track-by-track and layer-by-layer design
- Open Access
- 17 September 2018
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 99 (9-12) , 2903-2913
Influence of build layout and orientation on microstructural characteristics of electron beam melted Alloy 718
- 17 September 2018
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 99 (9-12) , 2903-2913
Open AccessInfluence of build layout and orientation on microstructural characteristics of electron beam melted Alloy 718
- Open Access
- 1 June 2018
- Published by Walter de Gruyter GmbH in Powder Metallurgy Progress
- Vol. 18 (1) , 40-48
Effect of Powder Recycling on the Fracture Behavior of Electron Beam Melted Alloy 718
Understanding the effect of powder feedstock alterations during multicycle additive manufacturing on the quality of built components is crucial to meet the requirements on critical parts for aerospace engine applications. In this study, powder recycling of Alloy 718 during electron beam melting was studied to understand its influence on fracture behavior of Charpy impact test bars. High resolution scanning electron microscopy was employed for fracture surface analysis on test bars produced from virgin and recycled powder. For all investigated samples, an intergranular type of fracture, initiated by non-metallic phases and bonding defects, was typically observed in the regions close to or within the contour zone. The fracture mode in the bulk of the samples was mainly moderately ductile dimple fracture. The results show a clear correlation between powder degradation during multi-cycle powder reuse and the amount of damage relevant defects observed on the fracture surfaces. In particular, samples produced from recycled powder show a significant amount of aluminum-rich oxide defects, originating from aluminum-rich oxide particulates on the surface of the recycled powder.
- 1 June 2018
- Published by Walter de Gruyter GmbH in Powder Metallurgy Progress
- Vol. 18 (1) , 40-48
Open AccessEffect of Powder Recycling on the Fracture Behavior of Electron Beam Melted Alloy 718
Understanding the effect of powder feedstock alterations during multicycle additive manufacturing on the quality of built components is crucial to meet the requirements on critical parts for aerospace engine applications. In this study, powder recycling of Alloy 718 during electron beam melting was studied to understand its influence on fracture behavior of Charpy impact test bars. High resolution scanning electron microscopy was employed for fracture surface analysis on test bars produced from virgin and recycled powder. For all investigated samples, an intergranular type of fracture, initiated by non-metallic phases and bonding defects, was typically observed in the regions close to or within the contour zone. The fracture mode in the bulk of the samples was mainly moderately ductile dimple fracture. The results show a clear correlation between powder degradation during multi-cycle powder reuse and the amount of damage relevant defects observed on the fracture surfaces. In particular, samples produced from recycled powder show a significant amount of aluminum-rich oxide defects, originating from aluminum-rich oxide particulates on the surface of the recycled powder.
- 13 May 2018
- Published by Springer Nature in The Minerals, Metals & Materials Series
- p. 643-654
Microstructure Development in Track-by-Track Melting of EBM-Manufactured Alloy 718
- 13 May 2018
- Published by Springer Nature in The Minerals, Metals & Materials Series
- p. 643-654
Microstructure Development in Track-by-Track Melting of EBM-Manufactured Alloy 718
- Open Access
- 6 September 2017
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 94 (5-8) , 2199-2207
Influence of laser exposure time and point distance on 75-μm-thick layer of selective laser melted Alloy 718
- 6 September 2017
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 94 (5-8) , 2199-2207
Open AccessInfluence of laser exposure time and point distance on 75-μm-thick layer of selective laser melted Alloy 718