Oscar Ricardo Sandoval
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Oscar Ricardo Sandoval has a total of 34 co-authors. Here are the top co-authors by number of shared publications:
- Augusto César Teixeira Malaquias
Federal University of Minas Gerais - UFMG
3 shared publications - José Guilherme Coelho Baêta
Graduate Program in Mechanical Engineering, Universidade Federal de Minas Gerais (PPGMEC-UFMG), Belo Horizonte CEP 31270-901, MG, Brazil
3 shared publications - Natalia Regina Souza Araujo
Universidade Federal de Minas Gerais
3 shared publications Ramón Molina Valle
3 shared publicationsBryan Castro Caetano
2 shared publications- Fabrício José Pacheco Pujatti
Department of Mechanical Engineering, Federal University of Minas Gerais, Minas Gerais, Brazil
2 shared publications
Latest Publications
- Open Access
- 13 April 2026
- Published by Elsevier in SSRN Electronic Journal
Understanding Ethanol Combustion by a Macro Kinetic Modelling in Spark Ignition Engines using Neural Network and Mass Fraction Burned data
This study presents a kinetic description of hydrous ethanol combustion in a spark-ignition single-cylinder research engine using experimental mass fraction burned (MFB) data and artificial neural networks (ANN). In-cylinder pressure measurements were obtained at indicated mean effective pressure (IMEP = 7 bar) and at three engine speeds (1900, 2200, and 3000 rpm). The normalized MFB curves were treated as a global conversion and analyzed through a nonlinear isoconversional method combined with ANN to determine the kinetic triplet as the apparent activation energy, pre-exponential factor, and combined mechanism, without relying on detailed chemical kinetic reactions. The apparent activation energy increased along conversion degree, ranging from approximately [[EQUATION]]at the onset of combustion to 24 [[EQUATION]]at about 70% conversion, followed by a slight decrease in the final stages until 16.5 [[EQUATION]], revealing a multistage process divided into three kinetic events associated with fuel activation, intermediate oxidation, and radical-driven reactions. The ANN results indicated that combustion is governed by a combination of Avrami–Erofeev and first-order models, with diffusion effects in intermediate stages. The proposed methodology was compared with the Wiebe model and validated against experimental MFB and heat release rate data, including operating conditions at engine speeds not used during the ANN training process. This approach provides a complementary and physically interpretable framework to correlate ethanol combustion stages directly with engine experimental data.
- 13 April 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessUnderstanding Ethanol Combustion by a Macro Kinetic Modelling in Spark Ignition Engines using Neural Network and Mass Fraction Burned data
This study presents a kinetic description of hydrous ethanol combustion in a spark-ignition single-cylinder research engine using experimental mass fraction burned (MFB) data and artificial neural networks (ANN). In-cylinder pressure measurements were obtained at indicated mean effective pressure (IMEP = 7 bar) and at three engine speeds (1900, 2200, and 3000 rpm). The normalized MFB curves were treated as a global conversion and analyzed through a nonlinear isoconversional method combined with ANN to determine the kinetic triplet as the apparent activation energy, pre-exponential factor, and combined mechanism, without relying on detailed chemical kinetic reactions. The apparent activation energy increased along conversion degree, ranging from approximately [[EQUATION]]at the onset of combustion to 24 [[EQUATION]]at about 70% conversion, followed by a slight decrease in the final stages until 16.5 [[EQUATION]], revealing a multistage process divided into three kinetic events associated with fuel activation, intermediate oxidation, and radical-driven reactions. The ANN results indicated that combustion is governed by a combination of Avrami–Erofeev and first-order models, with diffusion effects in intermediate stages. The proposed methodology was compared with the Wiebe model and validated against experimental MFB and heat release rate data, including operating conditions at engine speeds not used during the ANN training process. This approach provides a complementary and physically interpretable framework to correlate ethanol combustion stages directly with engine experimental data.
- 1 January 2026
- Published by Sociedade Brasileira de Quimica (SBQ) in Journal of the Brazilian Chemical Society
Combustion Kinetics of Gasoline in a Spark-Ignition Engine Using an ANN-Based Analysis of Mass Fraction Burned Data: Effect of a Commercial Nanoparticle Additive
Improving the efficiency of gasoline-fueled engines remains important for reducing fuel consumption during the energy transition. However, the kinetic effects of nanoparticle-based fuel additives under actual engine conditions remain insufficiently understood. This study investigated the influence of a commercial nanoparticle additive on the combustion kinetics and performance of Brazilian commercial E27 gasoline. Experiments were conducted in a single-cylinder research engine at a constant indicated mean effective pressure of 7 bar and engine speeds of 1900, 2200, and 3000 rpm. Experimental mass fraction burned profiles were analyzed using a previously validated artificial neural network (ANN) based isoconversional methodology to determine the complete apparent kinetic triplet, activation energy, frequency factor, and relative contributions of kinetic models, throughout combustion. Unlike conventional black-box ANN applications, the proposed framework provides a physically interpretable description of combustion kinetics directly from engine data. An objective kinetic-compensation and segmented-regression analysis identified two apparent kinetic events, with the transition shifting from a conversion degree of 0.40 for commercial gasoline to 0.65 for gasoline containing the additive. Nanoparticle addition increased the duration of the first event and reduced the second event. The additive also redistributed the contributions of the apparent kinetic models, demonstrating a modification of the combustion pathway. These kinetic changes were accompanied by a 4.1-5.3% increase in combustion efficiency and a 2.5-5.1% reduction in indicated specific fuel consumption. The proposed methodology therefore advances ANN-based combustion analysis from macroscopic prediction toward physically interpretable kinetic assessment.
- 1 January 2026
- Published by Sociedade Brasileira de Quimica (SBQ) in Journal of the Brazilian Chemical Society
Combustion Kinetics of Gasoline in a Spark-Ignition Engine Using an ANN-Based Analysis of Mass Fraction Burned Data: Effect of a Commercial Nanoparticle Additive
Improving the efficiency of gasoline-fueled engines remains important for reducing fuel consumption during the energy transition. However, the kinetic effects of nanoparticle-based fuel additives under actual engine conditions remain insufficiently understood. This study investigated the influence of a commercial nanoparticle additive on the combustion kinetics and performance of Brazilian commercial E27 gasoline. Experiments were conducted in a single-cylinder research engine at a constant indicated mean effective pressure of 7 bar and engine speeds of 1900, 2200, and 3000 rpm. Experimental mass fraction burned profiles were analyzed using a previously validated artificial neural network (ANN) based isoconversional methodology to determine the complete apparent kinetic triplet, activation energy, frequency factor, and relative contributions of kinetic models, throughout combustion. Unlike conventional black-box ANN applications, the proposed framework provides a physically interpretable description of combustion kinetics directly from engine data. An objective kinetic-compensation and segmented-regression analysis identified two apparent kinetic events, with the transition shifting from a conversion degree of 0.40 for commercial gasoline to 0.65 for gasoline containing the additive. Nanoparticle addition increased the duration of the first event and reduced the second event. The additive also redistributed the contributions of the apparent kinetic models, demonstrating a modification of the combustion pathway. These kinetic changes were accompanied by a 4.1-5.3% increase in combustion efficiency and a 2.5-5.1% reduction in indicated specific fuel consumption. The proposed methodology therefore advances ANN-based combustion analysis from macroscopic prediction toward physically interpretable kinetic assessment.
- Top Cited Papers
- 24 September 2024
- Published by Elsevier in Energy and Buildings
- Vol. 323
Review of energy efficiency and technological advancements in data center power systems
- 24 September 2024
- Published by Elsevier in Energy and Buildings
- Vol. 323
Top Cited PapersReview of energy efficiency and technological advancements in data center power systems
- Open Access
- 11 May 2022
- Published by MDPI AG in Lubricants
- Vol. 10 (5) , 92
Influence of Fluid Film Bearings with Different Axial Groove Shapes on Automotive Turbochargers: An Experimental Study
Most commercial automotive turbochargers (TC) employ semi-floating ring bearings (SFRB) with axial groove shapes. In order to bring some insights into the role played by the axial groove geometry on the dynamics of TC, this work deals with an experimental study of the rotordynamic behavior of a stock automotive turbocharger operating on SFRB with two different groove shapes, which have the same volume and width, and with the same number of grooves. The rotating machine behavior has been evaluated under different operating conditions using a test bench specially designed to analyze turbochargers. Rotordynamic (RD) characteristics of automotive turbochargers are estimated to evaluate the influence of the axial groove geometry on the machine vibratory behavior. Frequency spectra and orbital plots of the rotor are obtained from accelerometers and proximity probes mounted on the turbocharger. The comparative analysis of the vibrational behavior of automotive turbochargers running on different supporting systems allows the identification of the role played by the axial grooves on the machine rotordynamic performance. The experimental results rendered in this work permit to classify the influence of the axial groove geometry on the turbocharger rotordynamic behavior for several speed and flow conditions.
- 11 May 2022
- Published by MDPI AG in Lubricants
- Vol. 10 (5) , 92
Open AccessInfluence of Fluid Film Bearings with Different Axial Groove Shapes on Automotive Turbochargers: An Experimental Study
Most commercial automotive turbochargers (TC) employ semi-floating ring bearings (SFRB) with axial groove shapes. In order to bring some insights into the role played by the axial groove geometry on the dynamics of TC, this work deals with an experimental study of the rotordynamic behavior of a stock automotive turbocharger operating on SFRB with two different groove shapes, which have the same volume and width, and with the same number of grooves. The rotating machine behavior has been evaluated under different operating conditions using a test bench specially designed to analyze turbochargers. Rotordynamic (RD) characteristics of automotive turbochargers are estimated to evaluate the influence of the axial groove geometry on the machine vibratory behavior. Frequency spectra and orbital plots of the rotor are obtained from accelerometers and proximity probes mounted on the turbocharger. The comparative analysis of the vibrational behavior of automotive turbochargers running on different supporting systems allows the identification of the role played by the axial grooves on the machine rotordynamic performance. The experimental results rendered in this work permit to classify the influence of the axial groove geometry on the turbocharger rotordynamic behavior for several speed and flow conditions.
- 1 March 2019
- Published by Elsevier in Energy Conversion and Management
- Vol. 184, 510-520
A novel methodology on beta-type Stirling engine simulation using CFD
- 1 March 2019
- Published by Elsevier in Energy Conversion and Management
- Vol. 184, 510-520
A novel methodology on beta-type Stirling engine simulation using CFD
- 1 February 2019
- Published by Elsevier in Energy Conversion and Management
- Vol. 181, 189-201
Modelling, simulation and thermal analysis of a solar dish/Stirling system: A case study in Natal, Brazil
- 1 February 2019
- Published by Elsevier in Energy Conversion and Management
- Vol. 181, 189-201
Modelling, simulation and thermal analysis of a solar dish/Stirling system: A case study in Natal, Brazil
- 19 August 2018
- Published by Springer Nature
- p. 388-397
Influence of Temperature and Injection Pressure of Lubrication in the Vibration of an Automotive Turbocharger
- 19 August 2018
- Published by Springer Nature
- p. 388-397
Influence of Temperature and Injection Pressure of Lubrication in the Vibration of an Automotive Turbocharger