I. S. Belashova
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
I. S. Belashova has a total of 17 co-authors. Here are the top co-authors by number of shared publications:
- Larisa Petrova
Moscow Automobile and Road Construction State Technical University (MADI), Moscow, Russia
4 shared publications - P. S. Bibikov
OOO RPE Nitrid, Saratov, Russia
2 shared publications A S Sergeeva
Moscow Automobile and Road Construction State Technical University (MADI), 64, Leningradsky prospect, Moscow, 125319, Russia
1 shared publicationA. O. Shashkov
Moscow State Automobile and Road Technical University (MADI)
1 shared publication- Banga-N. Leocent
Moscow Automobile and Road Construction State Technical University (MADI), Moscow, Russia
1 shared publication D. P. Shashkov
Moscow Automobile and Road State Engineering University (MADI), Moscow, Russia
1 shared publication
Latest Publications
- 1 August 2026
- Published by Pleiades Publishing Ltd in Journal of Experimental and Theoretical Physics
- Vol. 143 (2) , 166-172
Physical and Mechanical Tests of Protective Coatings on Metal Surfaces
This paper proposes a new method for estimating the elastic modulus of protective polymer coatings based on standard tensile tests on three-layer strip specimens. The proposed method derives the coating’s elastic modulus from a comparison of experimental elastic modulus values obtained for the base material (08 PS steel) and the effective elastic modulus for specimens coated with the studied coatings. The differences between these values are 10–15%. In this case, the accuracy of estimating the coating’s elastic modulus largely depends on the accuracy of stress and strain determination during testing of the material specimens, which were measured using ZWICK Z100 precision equipment and mechanical testing methods. Using this equipment, tensile tests were performed on four protective polymer coatings applied to the specimen surfaces. The elastic modulus values of the coatings were calculated using the rule of mixtures. For two modifications of the studied coatings, the elastic modulus values were obtained from four-point bending tests. It was shown that both methods yield similar values for the elastic modulus of the coatings.
- 1 August 2026
- Published by Pleiades Publishing Ltd in Journal of Experimental and Theoretical Physics
- Vol. 143 (2) , 166-172
Physical and Mechanical Tests of Protective Coatings on Metal Surfaces
This paper proposes a new method for estimating the elastic modulus of protective polymer coatings based on standard tensile tests on three-layer strip specimens. The proposed method derives the coating’s elastic modulus from a comparison of experimental elastic modulus values obtained for the base material (08 PS steel) and the effective elastic modulus for specimens coated with the studied coatings. The differences between these values are 10–15%. In this case, the accuracy of estimating the coating’s elastic modulus largely depends on the accuracy of stress and strain determination during testing of the material specimens, which were measured using ZWICK Z100 precision equipment and mechanical testing methods. Using this equipment, tensile tests were performed on four protective polymer coatings applied to the specimen surfaces. The elastic modulus values of the coatings were calculated using the rule of mixtures. For two modifications of the studied coatings, the elastic modulus values were obtained from four-point bending tests. It was shown that both methods yield similar values for the elastic modulus of the coatings.
- 1 July 2026
- Published by Pleiades Publishing Ltd in Journal of Experimental and Theoretical Physics
- Vol. 143 (1) , 7-12
Improving the Wear Resistance of Alloy Steel by Isothermal Stepwise Nitriding
The article investigates an isothermal staged nitriding process for 40KhN2MA structural steel, comprising a saturation stage in an ammonia–air mixture followed by a stage in pure ammonia. Experimental data reveal the patterns of nitride zone formation as a function of temperature and the total duration of the staged process. The effect of nitriding regimes on the growth kinetics and microhardness of the nitrided layer is examined. Tribological tests demonstrate improved wear resistance of the nitrided steel, characterized by an extended run-in period, a reduced friction coefficient, and decreased linear wear parameters. An optimal staged process regime is determined to produce a nitrided layer structure that ensures maximum wear resistance under dry sliding conditions.
- 1 July 2026
- Published by Pleiades Publishing Ltd in Journal of Experimental and Theoretical Physics
- Vol. 143 (1) , 7-12
Improving the Wear Resistance of Alloy Steel by Isothermal Stepwise Nitriding
The article investigates an isothermal staged nitriding process for 40KhN2MA structural steel, comprising a saturation stage in an ammonia–air mixture followed by a stage in pure ammonia. Experimental data reveal the patterns of nitride zone formation as a function of temperature and the total duration of the staged process. The effect of nitriding regimes on the growth kinetics and microhardness of the nitrided layer is examined. Tribological tests demonstrate improved wear resistance of the nitrided steel, characterized by an extended run-in period, a reduced friction coefficient, and decreased linear wear parameters. An optimal staged process regime is determined to produce a nitrided layer structure that ensures maximum wear resistance under dry sliding conditions.
- 1 May 2026
- Published by Pleiades Publishing Ltd in Journal of Experimental and Theoretical Physics
- Vol. 142 (5) , 622-628
Selecting the Duration of the Control Interval of the Search Optimization Algorithm under the Conditions of the Nonstationary Nature of the Simulation Modeling Process
This article examines the assessment of behavior of a search engine optimization algorithm when it is directly integrated into a simulation model of a complex dynamic system and when the search direction is selected over relatively short sample trajectories of the simulation process. In this problem formulation, evaluating the optimization process effectiveness requires constructing probabilistic estimates of the nonstationary simulation process since it has no time to reach a steady state. Therefore, this paper derives analytical expressions for the trend of mean integral estimates of nonstationary processes defined by the simulation model and its variance as a function of the estimation interval. The resulting relationships provide the basis for estimating the convergence rate of search engine optimization.
- 1 May 2026
- Published by Pleiades Publishing Ltd in Journal of Experimental and Theoretical Physics
- Vol. 142 (5) , 622-628
Selecting the Duration of the Control Interval of the Search Optimization Algorithm under the Conditions of the Nonstationary Nature of the Simulation Modeling Process
This article examines the assessment of behavior of a search engine optimization algorithm when it is directly integrated into a simulation model of a complex dynamic system and when the search direction is selected over relatively short sample trajectories of the simulation process. In this problem formulation, evaluating the optimization process effectiveness requires constructing probabilistic estimates of the nonstationary simulation process since it has no time to reach a steady state. Therefore, this paper derives analytical expressions for the trend of mean integral estimates of nonstationary processes defined by the simulation model and its variance as a function of the estimation interval. The resulting relationships provide the basis for estimating the convergence rate of search engine optimization.
- 30 May 2022
- Published by Bryansk State Technical University BSTU in Science intensive technologies in mechanical engineering
- Vol. 2022 (5) , 11-19
A systematic approach to the problem of hardfacing of aluminum alloys using laser treatment
The paper studies the matter of theoretical regularities of reactant transport mechanisms in laser surface alloyage of aluminum alloys. It is shown that, along with the traditional diffusion saturation a convective mechanism of reactant transport and the process of refractory particles introduction play a significant role for alloying components flow entering a molten pool in the alloyed zone. An increase in wear resistance was found if alloying aluminum alloy D16 with chromium, nickel and niobium disilicide.
- 30 May 2022
- Published by Bryansk State Technical University BSTU in Science intensive technologies in mechanical engineering
- Vol. 2022 (5) , 11-19
A systematic approach to the problem of hardfacing of aluminum alloys using laser treatment
The paper studies the matter of theoretical regularities of reactant transport mechanisms in laser surface alloyage of aluminum alloys. It is shown that, along with the traditional diffusion saturation a convective mechanism of reactant transport and the process of refractory particles introduction play a significant role for alloying components flow entering a molten pool in the alloyed zone. An increase in wear resistance was found if alloying aluminum alloy D16 with chromium, nickel and niobium disilicide.
- 30 December 2021
- Published by Bryansk State Technical University BSTU in Science intensive technologies in mechanical engineering
- Vol. 2021 (12) , 12-19
The effect of stadial nitrogenization on the structure and properties of martensitic steel 13X11N2V2MF
A new method of gas nitriding is presented, which produces obtaining high-quality diffusion layers that meet the requirements of the use for various purposes, including aviation ones. Peculiar properties of highly alloyed martensitic steel nitriding after stadial thermo-gas-cyclic nitrogenization under partially dissociated ammonia with air additives have been examined. The results of metallographic studies, diagnostic leach, tests for wear resistance, impact hardness and corrosion stability, depending on the test mode are presented.
- 30 December 2021
- Published by Bryansk State Technical University BSTU in Science intensive technologies in mechanical engineering
- Vol. 2021 (12) , 12-19
The effect of stadial nitrogenization on the structure and properties of martensitic steel 13X11N2V2MF
A new method of gas nitriding is presented, which produces obtaining high-quality diffusion layers that meet the requirements of the use for various purposes, including aviation ones. Peculiar properties of highly alloyed martensitic steel nitriding after stadial thermo-gas-cyclic nitrogenization under partially dissociated ammonia with air additives have been examined. The results of metallographic studies, diagnostic leach, tests for wear resistance, impact hardness and corrosion stability, depending on the test mode are presented.
- Open Access
- 1 February 2021
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 1064 (1) , 012004
New nitriding process of high-alloyed maraging steel for cryogenic operation
The paper considers the gas nitriding process with cyclic alternation of atmospheres: ammonia and an ammonia mixture with air for strengthening the corrosion-resistant high-alloyed steel 03Cr11Ni10Mo2Ti, designed to operate at cryogenic temperatures. The formation in steel of a nitrided layer of 130—150μm thickness with increased microhardness (more than 12GPa) is shown experimentally. During the final stage in the ammonia and air environment, iron oxides remain in the compound zone, and a sharp drop in hardness is observed at the border of the core. At the completion of the cyclic process with the stage of saturation in ammonia, a nitrides zone is formed based on the γ′-phase, the layer thickness increases (up to 180(…200μm) and the microhardness profile is smoothed, which reduces the risk of embrittlement.
- 1 February 2021
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 1064 (1) , 012004
Open AccessNew nitriding process of high-alloyed maraging steel for cryogenic operation
The paper considers the gas nitriding process with cyclic alternation of atmospheres: ammonia and an ammonia mixture with air for strengthening the corrosion-resistant high-alloyed steel 03Cr11Ni10Mo2Ti, designed to operate at cryogenic temperatures. The formation in steel of a nitrided layer of 130—150μm thickness with increased microhardness (more than 12GPa) is shown experimentally. During the final stage in the ammonia and air environment, iron oxides remain in the compound zone, and a sharp drop in hardness is observed at the border of the core. At the completion of the cyclic process with the stage of saturation in ammonia, a nitrides zone is formed based on the γ′-phase, the layer thickness increases (up to 180(…200μm) and the microhardness profile is smoothed, which reduces the risk of embrittlement.
- 1 January 2018
- Published by Allerton Press in Russian Engineering Research
- Vol. 38 (1) , 53-56
Improving the Properties of Low-Alloy and Carbon Steel Tools by Cyclic Nitriding
Cyclic nitriding characterized by uniform alternation of cycles with high and low nitrogen potential is considered. In the active stage of the process, the surface layer of the steel is saturated...
- 1 January 2018
- Published by Allerton Press in Russian Engineering Research
- Vol. 38 (1) , 53-56
Improving the Properties of Low-Alloy and Carbon Steel Tools by Cyclic Nitriding
Cyclic nitriding characterized by uniform alternation of cycles with high and low nitrogen potential is considered. In the active stage of the process, the surface layer of the steel is saturated...
- 29 September 2012
- Published by Springer Nature in Metal Science and Heat Treatment
- Vol. 54 (5-6) , 315-319
Kinetics of growth of the diffusion layer in nitriding by the thermogasocyclic method
- 29 September 2012
- Published by Springer Nature in Metal Science and Heat Treatment
- Vol. 54 (5-6) , 315-319
Kinetics of growth of the diffusion layer in nitriding by the thermogasocyclic method
- 4 November 2010
- Published by Springer Nature in Metal Science and Heat Treatment
- Vol. 52 (5-6) , 229-233
Controlled processes of nitriding under conditions of a thermal gas cycle
- 4 November 2010
- Published by Springer Nature in Metal Science and Heat Treatment
- Vol. 52 (5-6) , 229-233
Controlled processes of nitriding under conditions of a thermal gas cycle