Jorge Gómez
Research Subjects
Research Interests
Jorge Gómez has a total of 24 co-authors. Here are the top co-authors by number of shared publications:
- Francisco Javier Cervantes
Laboratory for Research on Advanced Processes for Water Treatment, Engineering Institute, Campus Juriquilla, Universidad Nacional Autónoma de México (UNAM), Blvd. Juriquilla 3001, 76230 Querétaro, Mexico
5 shared publications - Ricardo Beristain Cardoso
Autonomous Metropolitan University, Lerma Unit Lerma de Villada Mexico
3 shared publications Anne-Claire Texier
Universidad Autónoma Metropolitana-Iztapalapa
2 shared publications- Francisco José Fernández
Universidad Autónoma Metropolitana-Iztapalapa
2 shared publications - Gehovana González-Blanco
Universidad Autónoma del Estado de México
2 shared publications - Anne-Claire Texier
Department of Biotechnology-CBS, Metropolitan Autonomous University Iztapalapa, Mexico City, Mexico
1 shared publication
Latest Publications
- 12 June 2015
- Published by Springer Nature in Applied Biochemistry and Biotechnology
- Vol. 176 (8) , 2120-2130
Concurrence of Anaerobic Ammonium Oxidation and Organotrophic Denitrification in Presence of p-Cresol
This study was carried out to evaluate the capacity of anaerobic granular sludge for oxidizing ammonium and p-cresol with nitrate as terminal electron acceptor. Kinetics for the anaerobic oxidation of ammonium and p-cresol is described in this paper. The phenolic compound was very efficiently consumed, achieving 65 % of mineralization. Ammonium and nitrate were also consumed at 83 and 92 %, respectively, being the main product N2. Anaerobic ammonium oxidation was promoted owing to accumulation of nitrite, and it allowed the synergy of anaerobic ammonium oxidation and organotrophic denitrification for the simultaneous removal of ammonium, nitrate, and p-cresol. A carbonaceous intermediate partially identified was transiently accumulated, and it transitorily truncated the respiratory process of denitrification. These experimental results might be considered for defining strategies in order to remove nitrate, ammonium, and phenolic compounds from wastewaters.
- 12 June 2015
- Published by Springer Nature in Applied Biochemistry and Biotechnology
- Vol. 176 (8) , 2120-2130
Concurrence of Anaerobic Ammonium Oxidation and Organotrophic Denitrification in Presence of p-Cresol
This study was carried out to evaluate the capacity of anaerobic granular sludge for oxidizing ammonium and p-cresol with nitrate as terminal electron acceptor. Kinetics for the anaerobic oxidation of ammonium and p-cresol is described in this paper. The phenolic compound was very efficiently consumed, achieving 65 % of mineralization. Ammonium and nitrate were also consumed at 83 and 92 %, respectively, being the main product N2. Anaerobic ammonium oxidation was promoted owing to accumulation of nitrite, and it allowed the synergy of anaerobic ammonium oxidation and organotrophic denitrification for the simultaneous removal of ammonium, nitrate, and p-cresol. A carbonaceous intermediate partially identified was transiently accumulated, and it transitorily truncated the respiratory process of denitrification. These experimental results might be considered for defining strategies in order to remove nitrate, ammonium, and phenolic compounds from wastewaters.
- Open Access
- 20 November 2014
- Published by IWA Publishing in Water Science & Technology
- Vol. 71 (1) , 97-104
Effect of sulfate and lactate loading rates on the respiration process and microbial population changes measured by ecological indices
In a sulfate reducing process, increasing loading rates and sulfide accumulation may induce population changes resulting in decreasing effectiveness of the process. Thus, the relationship between microbial metabolism changes and population dynamics was studied. An upflow anaerobic sludge blanket reactor was operated at different sulfate loading rates (SLR), from 290 to 981 mg SO4 − S/L d at a constant carbon/sulfur ratio of 0.75. When the SLR was increased, the total organic carbon and sulfate consumption efficiencies decreased to nearly 30% and 25%, respectively. The acetate and propionate yields increased with increasing SLR and 385 ± 7 mg sulfide-S/L d was reached. The ecological indices, determined by random amplified polymorphic DNA and denaturing gradient gel electrophoresis techniques, diversity and evenness were found to be constant, and similarity coefficient values remained higher than 76%. The results suggest that the microbial population changes were negligible compared with metabolic changes when SLR was increased. The sulfide accumulation did not modify the microbial diversity. The sequencing of 16S rRNA genes showed strains related to sulfate reducing, fermentation, and methanogenesis processes. The results indicated that the decreasing of effectiveness, under the experimental conditions tested, was dependent more on operational parameters than microbial changes.
- 20 November 2014
- Published by IWA Publishing in Water Science & Technology
- Vol. 71 (1) , 97-104
Open AccessEffect of sulfate and lactate loading rates on the respiration process and microbial population changes measured by ecological indices
In a sulfate reducing process, increasing loading rates and sulfide accumulation may induce population changes resulting in decreasing effectiveness of the process. Thus, the relationship between microbial metabolism changes and population dynamics was studied. An upflow anaerobic sludge blanket reactor was operated at different sulfate loading rates (SLR), from 290 to 981 mg SO4 − S/L d at a constant carbon/sulfur ratio of 0.75. When the SLR was increased, the total organic carbon and sulfate consumption efficiencies decreased to nearly 30% and 25%, respectively. The acetate and propionate yields increased with increasing SLR and 385 ± 7 mg sulfide-S/L d was reached. The ecological indices, determined by random amplified polymorphic DNA and denaturing gradient gel electrophoresis techniques, diversity and evenness were found to be constant, and similarity coefficient values remained higher than 76%. The results suggest that the microbial population changes were negligible compared with metabolic changes when SLR was increased. The sulfide accumulation did not modify the microbial diversity. The sequencing of 16S rRNA genes showed strains related to sulfate reducing, fermentation, and methanogenesis processes. The results indicated that the decreasing of effectiveness, under the experimental conditions tested, was dependent more on operational parameters than microbial changes.
- 30 August 2014
- Published by Springer Nature in Applied Biochemistry and Biotechnology
- Vol. 174 (6) , 2171-2180
Consumption of 2-Chlorophenol Using Anaerobic Sludge: Physiological and Kinetic Analysis
Chlorophenols are toxic and recalcitrant compounds produced by many industrial. Different strategies have been used to improve their biological consumption, but there is insufficient information to understand how the process is carried out. The objective of this study was to evaluate in batch tests the effect of the addition of phenol, acetate, or glucose as electron donors at different concentrations on the efficiencies, yields, and specific rates of 2-chlorophenol (2-CP) consumption. The addition of phenol (177.6 mg C/L), acetate (127.6 mg C/L), or glucose (77.6 mg C/L) increased the 2-CP consumption efficiency up to 54.6, 98.6, and 97.8 %, respectively. With respect to the control assay without electron donor, the specific rate of 2-CP consumption was up to 2.5 times higher with phenol (177.6 mg C/L), 8.4 times higher with acetate (127.6 mg C/L), and 3 times higher with glucose (127.6 mg C/L). The results showed that the type and concentration of electron donor determine the physiological behavior of the anaerobic sludge, modifying efficiency, yield, and specific rate values of the 2-CP consumption process. The addition of readily oxidable cosubstrates seems to be a good alternative and might be used for the biological treatment of industrial wastewater polluted with chlorinated phenols.
- 30 August 2014
- Published by Springer Nature in Applied Biochemistry and Biotechnology
- Vol. 174 (6) , 2171-2180
Consumption of 2-Chlorophenol Using Anaerobic Sludge: Physiological and Kinetic Analysis
Chlorophenols are toxic and recalcitrant compounds produced by many industrial. Different strategies have been used to improve their biological consumption, but there is insufficient information to understand how the process is carried out. The objective of this study was to evaluate in batch tests the effect of the addition of phenol, acetate, or glucose as electron donors at different concentrations on the efficiencies, yields, and specific rates of 2-chlorophenol (2-CP) consumption. The addition of phenol (177.6 mg C/L), acetate (127.6 mg C/L), or glucose (77.6 mg C/L) increased the 2-CP consumption efficiency up to 54.6, 98.6, and 97.8 %, respectively. With respect to the control assay without electron donor, the specific rate of 2-CP consumption was up to 2.5 times higher with phenol (177.6 mg C/L), 8.4 times higher with acetate (127.6 mg C/L), and 3 times higher with glucose (127.6 mg C/L). The results showed that the type and concentration of electron donor determine the physiological behavior of the anaerobic sludge, modifying efficiency, yield, and specific rate values of the 2-CP consumption process. The addition of readily oxidable cosubstrates seems to be a good alternative and might be used for the biological treatment of industrial wastewater polluted with chlorinated phenols.
- 30 March 2013
- Published by Wiley in Journal of Chemical Technology & Biotechnology
- Vol. 88 (12) , 2176-2180
Nitrite as oxidizing power for p‐cresol removal using a denitrifying sludge: kinetic study
Background: Chemical plants, oil refineries and petrochemical plants discharge wastewaters polluted with phenolic and nitrogen compounds. Denitrification is an economical and feasible process, however, metabolic and kinetic information is required in order to know and to control the limitations involved when nitrite is present or accumulated. The goal of this study was to study the kinetic behavior of a denitrifying sludge and to reduce nitrite at several p‐cresol‐C (p‐Cr) concentrations.Results: Over the 10 to 45 mg p‐Cr L−1 concentration range tested, nitrite reduction was linked to p‐Cr oxidation and the specific rate increased to 7.02 mg NO2−‐N g−1 VSS h, with CO2 and N2 the products. At higher initial p‐Cr concentrations, inhibition was observed, diminishing the specific rate to 1.60 mg NO2−‐N g−1 VSS h. Electron balance showed that p‐Cr consumption was carried out by two biological processes; denitrification and fermentation. The kinetic profile followed the Haldane model, with inhibition constant (Ki) of 35.75 mg p‐Cr L−1, affinity constant (Ks) of 20.32 mg p‐Cr L−1 and maximum specific nitrite reduction (qmax) of 9.48 mg NO2−‐N g−1 VSS h.CONCLUSIONS: The results suggest that p‐cresol can be removed by denitrification and fermentation. Kinetic information should be considered for designing and operating denitrifying reactors to treat industrial wastewaters containing phenolic compounds and nitrite. © 2013 Society of Chemical Industry
- 30 March 2013
- Published by Wiley in Journal of Chemical Technology & Biotechnology
- Vol. 88 (12) , 2176-2180
Nitrite as oxidizing power for p‐cresol removal using a denitrifying sludge: kinetic study
Background: Chemical plants, oil refineries and petrochemical plants discharge wastewaters polluted with phenolic and nitrogen compounds. Denitrification is an economical and feasible process, however, metabolic and kinetic information is required in order to know and to control the limitations involved when nitrite is present or accumulated. The goal of this study was to study the kinetic behavior of a denitrifying sludge and to reduce nitrite at several p‐cresol‐C (p‐Cr) concentrations.Results: Over the 10 to 45 mg p‐Cr L−1 concentration range tested, nitrite reduction was linked to p‐Cr oxidation and the specific rate increased to 7.02 mg NO2−‐N g−1 VSS h, with CO2 and N2 the products. At higher initial p‐Cr concentrations, inhibition was observed, diminishing the specific rate to 1.60 mg NO2−‐N g−1 VSS h. Electron balance showed that p‐Cr consumption was carried out by two biological processes; denitrification and fermentation. The kinetic profile followed the Haldane model, with inhibition constant (Ki) of 35.75 mg p‐Cr L−1, affinity constant (Ks) of 20.32 mg p‐Cr L−1 and maximum specific nitrite reduction (qmax) of 9.48 mg NO2−‐N g−1 VSS h.CONCLUSIONS: The results suggest that p‐cresol can be removed by denitrification and fermentation. Kinetic information should be considered for designing and operating denitrifying reactors to treat industrial wastewaters containing phenolic compounds and nitrite. © 2013 Society of Chemical Industry
- 12 August 2009
- Published by Oxford University Press (OUP) in Journal of Industrial Microbiology and Biotechnology
- Vol. 36 (11) , 1417-1424
Kinetic limitations during the simultaneous removal of p-cresol and sulfide in a denitrifying process
The aim of this study was to evaluate the capacity of a denitrifying consortium to achieve the simultaneous removal of nitrate, sulfide and p-cresol and elucidate the rate-limiting steps in the mixotrophic process. Nitrite reduction appeared as the most evident rate-limiting step in the denitrifying respiratory process. The nitrite reduction rate achieved was up to 57 times lower than the nitrate reduction rate during the simultaneous removal of sulfide and p-cresol. Negligible accumulation of N2O occurred in the denitrifying cultures corroborating that nitrite reduction was the main rate-limiting step of the respiratory process. A synergistic effect of nitrate and sulfide is proposed to explain the accumulation of nitrite. The study also points at the oxidation of S0 as another rate-limiting step in the denitrifying process. Different respiratory rates were achieved with the distinct electron donors provided (p-cresol and sulfide). The oxidation rate of p-cresol (qCRES) was generally higher (up to 2.6-fold in terms of reducing equivalents) than the sulfide oxidation rate (qS2−), except for the experiments performed at 100 mg S2− L−1 in which qS2− was slightly (~1.4-fold in terms of reducing equivalents) higher than qCRES. The present study provides kinetic information, which should be considered when designing and operating denitrifying reactors to treat industrial wastewaters containing large amounts of sulfurous, nitrogenous and phenolic contaminants such as those generated from petrochemical refineries.
- 12 August 2009
- Published by Oxford University Press (OUP) in Journal of Industrial Microbiology and Biotechnology
- Vol. 36 (11) , 1417-1424
Kinetic limitations during the simultaneous removal of p-cresol and sulfide in a denitrifying process
The aim of this study was to evaluate the capacity of a denitrifying consortium to achieve the simultaneous removal of nitrate, sulfide and p-cresol and elucidate the rate-limiting steps in the mixotrophic process. Nitrite reduction appeared as the most evident rate-limiting step in the denitrifying respiratory process. The nitrite reduction rate achieved was up to 57 times lower than the nitrate reduction rate during the simultaneous removal of sulfide and p-cresol. Negligible accumulation of N2O occurred in the denitrifying cultures corroborating that nitrite reduction was the main rate-limiting step of the respiratory process. A synergistic effect of nitrate and sulfide is proposed to explain the accumulation of nitrite. The study also points at the oxidation of S0 as another rate-limiting step in the denitrifying process. Different respiratory rates were achieved with the distinct electron donors provided (p-cresol and sulfide). The oxidation rate of p-cresol (qCRES) was generally higher (up to 2.6-fold in terms of reducing equivalents) than the sulfide oxidation rate (qS2−), except for the experiments performed at 100 mg S2− L−1 in which qS2− was slightly (~1.4-fold in terms of reducing equivalents) higher than qCRES. The present study provides kinetic information, which should be considered when designing and operating denitrifying reactors to treat industrial wastewaters containing large amounts of sulfurous, nitrogenous and phenolic contaminants such as those generated from petrochemical refineries.
- 1 May 2009
- Published by IWA Publishing in Water Science & Technology
- Vol. 59 (10) , 1945-1950
Effects of different quinoid redox mediators on the simultaneous removal of p-cresol and sulphide in a denitrifying process
The catalytic effects of different quinoid redox mediators (RM) on the simultaneous removal of sulphide and p-cresol in a denitrifying process were evaluated in batch studies. 2-Hydroxy-1,4-naphthoquinone (LAW) and anthraquinone-2,6-disulphonate (AQDS) did not significantly affect the sulphide oxidation rate, which, in contrast, was increased 14% in the presence of 1,2-naphthoquinone-4-sulphonate (NQS). The input of NQS on the oxidation of sulphide was also favourably reflected in a 13% higher sulphate production. All RM promoted a higher (up to 34% compared to the control lacking RM) degree of mineralization of p-cresol. LAW also supported a 47% higher denitrifying yield (YN2), compared to the control lacking quinones. Nevertheless, AQDS and NQS decreased the YN2 by 12–13%. Our results suggest that a proper scrutiny should be conducted before deciding the sort of quinone to be applied in denitrifying processes. The heterogeneous effects observed also advise to consider both the respiratory rates and the yields as important parameters for deciphering the impact of RM on denitrifying processes.
- 1 May 2009
- Published by IWA Publishing in Water Science & Technology
- Vol. 59 (10) , 1945-1950
Effects of different quinoid redox mediators on the simultaneous removal of p-cresol and sulphide in a denitrifying process
The catalytic effects of different quinoid redox mediators (RM) on the simultaneous removal of sulphide and p-cresol in a denitrifying process were evaluated in batch studies. 2-Hydroxy-1,4-naphthoquinone (LAW) and anthraquinone-2,6-disulphonate (AQDS) did not significantly affect the sulphide oxidation rate, which, in contrast, was increased 14% in the presence of 1,2-naphthoquinone-4-sulphonate (NQS). The input of NQS on the oxidation of sulphide was also favourably reflected in a 13% higher sulphate production. All RM promoted a higher (up to 34% compared to the control lacking RM) degree of mineralization of p-cresol. LAW also supported a 47% higher denitrifying yield (YN2), compared to the control lacking quinones. Nevertheless, AQDS and NQS decreased the YN2 by 12–13%. Our results suggest that a proper scrutiny should be conducted before deciding the sort of quinone to be applied in denitrifying processes. The heterogeneous effects observed also advise to consider both the respiratory rates and the yields as important parameters for deciphering the impact of RM on denitrifying processes.
- 14 April 2008
- Published by Wiley in Journal of Chemical Technology & Biotechnology
- Vol. 83 (12) , 1648-1657
Effect of loading rate on TOC consumption efficiency in a sulfate reducing process: sulfide effect in batch culture
BACKGROUND: The sulfate reducing process (SRP) was analyzed in order to identify factors that diminish the effectiveness of the SRP during wastewater treatment. The effect of different sulfate loading rates (SLR, 290 to 981 mg SO4‐S L−1d−1) and lactate at a stoichiometric C/S ratio of 0.75 on SRP was studied in an upflow anaerobic sludge blanket (UASB) reactor. The effect of sulfide concentration (0 to 200 mg sulfide‐S L−1) on SRP in batch culture was evaluated.RESULTS: When the SLR was increased, the total organic carbon (TOC) and sulfate consumption efficiencies decreased from 93% ± 3 to 66% ± 2 and 60% ± 5 to 45% ± 4, respectively. Acetate and propionate were accumulated. Microbial analysis showed the presence of microorganisms related with the SRP, fermentation and methanogenesis. In batch culture, when lactate and sulfate were present, SRP and fermentation were observed. When sulfide was added only SRP was observed. At concentrations higher than 150 mg sulfide‐S L−1 the efficiencies, yields and specific consumption rates (q) decreased.CONCLUSION: Based on the sulfide‐S/volatile suspended solid ratio, it was found that the decrease in efficiency and accumulation of acetate and propionate in the UASB reactor was not related to sulfide inhibition but to the q of acetate and propionate, which were up to 11 times lower than lactate. Copyright © 2008 Society of Chemical Industry
- 14 April 2008
- Published by Wiley in Journal of Chemical Technology & Biotechnology
- Vol. 83 (12) , 1648-1657
Effect of loading rate on TOC consumption efficiency in a sulfate reducing process: sulfide effect in batch culture
BACKGROUND: The sulfate reducing process (SRP) was analyzed in order to identify factors that diminish the effectiveness of the SRP during wastewater treatment. The effect of different sulfate loading rates (SLR, 290 to 981 mg SO4‐S L−1d−1) and lactate at a stoichiometric C/S ratio of 0.75 on SRP was studied in an upflow anaerobic sludge blanket (UASB) reactor. The effect of sulfide concentration (0 to 200 mg sulfide‐S L−1) on SRP in batch culture was evaluated.RESULTS: When the SLR was increased, the total organic carbon (TOC) and sulfate consumption efficiencies decreased from 93% ± 3 to 66% ± 2 and 60% ± 5 to 45% ± 4, respectively. Acetate and propionate were accumulated. Microbial analysis showed the presence of microorganisms related with the SRP, fermentation and methanogenesis. In batch culture, when lactate and sulfate were present, SRP and fermentation were observed. When sulfide was added only SRP was observed. At concentrations higher than 150 mg sulfide‐S L−1 the efficiencies, yields and specific consumption rates (q) decreased.CONCLUSION: Based on the sulfide‐S/volatile suspended solid ratio, it was found that the decrease in efficiency and accumulation of acetate and propionate in the UASB reactor was not related to sulfide inhibition but to the q of acetate and propionate, which were up to 11 times lower than lactate. Copyright © 2008 Society of Chemical Industry
- 14 March 2008
- Published by Wiley in Journal of Chemical Technology & Biotechnology
- Vol. 83 (9) , 1197-1203
Simultaneous sulfide and acetate oxidation under denitrifying conditions using an inverse fluidized bed reactor
- 14 March 2008
- Published by Wiley in Journal of Chemical Technology & Biotechnology
- Vol. 83 (9) , 1197-1203
Simultaneous sulfide and acetate oxidation under denitrifying conditions using an inverse fluidized bed reactor
- 1 January 2000
- Published by Springer Nature in Applied Biochemistry and Biotechnology
- Vol. 87 (3) , 189-202
Kinetic Study of Addition of Volatile Organic Compounds to a Nitrifying Sludge
The effects of different concentrations of several volatile organic compounds (VOC) such as ethanol, acetate, propionate, and butyrate ranging from 0 to 2000 mg/L as well as a mixture of volatile...
- 1 January 2000
- Published by Springer Nature in Applied Biochemistry and Biotechnology
- Vol. 87 (3) , 189-202
Kinetic Study of Addition of Volatile Organic Compounds to a Nitrifying Sludge
The effects of different concentrations of several volatile organic compounds (VOC) such as ethanol, acetate, propionate, and butyrate ranging from 0 to 2000 mg/L as well as a mixture of volatile...
- 1 January 1999
- Published by Springer Nature in Applied Biochemistry and Biotechnology
- Vol. 81 (1) , 13-22
Influence of Ammonium on the Performance of a Denitrifying Culture Under Heterotrophic Conditions
The effect of ammonium on a denitrifying reactor of the upflow anaerobic sludge blanket type was studied. At a constant nitrate loading rate (2500 mg NO3−-N/[L · d]), using acetate as organic...
- 1 January 1999
- Published by Springer Nature in Applied Biochemistry and Biotechnology
- Vol. 81 (1) , 13-22
Influence of Ammonium on the Performance of a Denitrifying Culture Under Heterotrophic Conditions
The effect of ammonium on a denitrifying reactor of the upflow anaerobic sludge blanket type was studied. At a constant nitrate loading rate (2500 mg NO3−-N/[L · d]), using acetate as organic...