JGJ. K. Good

J. K. Good

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


J. K. Good has a total of 12 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Residual Winding Stresses Due to Spatial Web Thickness Variation

    by J. K. Good, C. Mollamahmutoglu, R. Markum, J. W. Gale

    At the end of roll-to-roll (R2R) manufacturing process machines, the web substrate must be wound into rolls. Winding is the only means known to store and protect vast lengths of very thin webs for subsequent processing. Web thickness variation in wound rolls is a root cause of large manufacturing loss due to residual stress-related defects. Minute thickness variations down the length and across the web width can induce large residual stress variations and defects within the roll. Winding models allow the exploration of winding residual stresses whose variation has been affected by web thickness or coating imperfections. Knowledge of these stresses is used to mitigate manufacturing defects. Spot web thickness sensors are employed in R2R process lines that scan over the web width while the web is moving downstream through the process machine. Spatially, this provides a measure of web thickness in a zig-zag pattern. During manufacturing, the thickness variation is used as a control feedback parameter to manipulate a forming or coating die lip to reduce the web or coated web thickness variation. The thickness variation acceptable in process may be very different than that which is acceptable based on the residual stresses in the wound roll. It will be determined whether the thickness test data captured spatially for process feedback are sufficient to characterize the residual stresses in the wound roll. A winding model will be developed and verified that is used to characterize these residual stresses.


  • Boundary Conditions That Govern the Lateral Behavior of Flexible Webs in Roll to Roll Process Machines

    by B. Fu, A. Reddy, S. Vaijapurkar, R. Markum, J. K. Good

    Thin web materials are commonly transported through machinery where a process adds value to the web. The flexible web is supported intermittently by contact with rollers. The friction forces associated with this contact are largely responsible for determining the lateral mechanics and dynamics of the thin web transiting rollers in roll-to-roll process machinery. The investigation focuses on cases where slippage between the rollers and web has become substantial and has resulted in a complex lateral behavior of the web. Two methods are presented for investigating the frictional forces and the resulting lateral behavior. The first method employs explicit finite element (FE) dynamic analysis to study the lateral mechanics of the web after steady state behavior has been achieved. This method allows the direct study of the frictional forces. The second method employs Laser Doppler Velocimetry in a novel experimental noncontact technique to examine internal loads within the web, which were influenced by the frictional forces. Both methods are shown to provide results, which agree with one another and with previous analysis. The analyses are used to form a new friction boundary condition between a web and roller that will benefit other analysis methods.


  • Analysis of Large Deformation Wound Roll Models

    by C. Mollamahmutoglu, J. K. Good

    Almost all winding models incorporate the assumption of small linear deformations and strain in their development. These models treat the addition of a layer of web to a winding roll with linear analysis using linear strain theory. Very few winding models have been developed that incorporate large deformation theory although many models treat material nonlinearity. Tissue and nonwoven webs are highly extensible in-plane and highly compressible in the thickness dimension when compared to paper, plastic film, and metal foil webs. Winding models that embody large deformation theory should apply to all web materials. Such models may be wasteful in computation time for web materials such as paper, film, and foils where models that employ small deformation theory may provide sufficient accuracy. This would appear deterministic based upon the extensibility and compressibility of a web material, but the issue becomes more complex due to limitations in tension that can be exerted on the webs. Herein, a large deformation winding model will be developed. Results from this model will be used to benchmark results from other small and large deformation models, and with laboratory test data, a review of all results will be used to determine when or if large deformation winding models are required.


  • The Instability of Webs in Transport

    by J. A. Beisel, J. K. Good

    A method is presented for determining the two levels of instability that are associated with thin web materials traveling through process machinery. The first level of instability involves the out-of-plane buckling of expanses of web supported only by rollers at opposing ends. A method is developed using linear plate theory, which is verified by tests that show that this first level of instability can be predicted. The second level of instability involves the buckling of the web when it has taken the form of a cylindrical shell as it transits a roller. A nonlinear finite element method with strain dependent constitutive relations is developed and verified by tests to predict this second level of instability.