Michał Mendak

In this paper, the multiscale analysis of the reproduction accuracy of jaw geometry obtained via the use of selected orthodontic materials is discussed. Impressions were made from two types of impression material. An accuracy assessment of the model geometry mapping was performed using noncontact systems, including a fringe projection optical 3D scanner, computed tomography, and a focus variation microscope. Measurements were made in three modes for comparison, as were the silicone and polyether impression materials. These modes were a jaw model and impression, an impression and plaster model, and plaster and jaw models. The research results are presented as colorful maps of deviations. Data analysis showed that deviations were the smallest in the case of silicone and that the best fit occurred between the silicone impression and the plaster model. The conducted research confirmed the validity of the assumptions considering the use of multiscale analysis for geometric analysis. The use of modern multiscale measurement methods allows for shorter and more efficient prosthetic operations. At present, these devices are expensive and complicated to use, but developments in technology should simplify the process, and prosthetic professionals should be aware of the possibilities described in the paper.

The technology of producing threads, especially in materials that are difficult to cut, is a rare subject of research and scientific publications. The requirements for the production of these elements apply not only to the geometry, but also to the quality of the surface obtained. This is particularly important in the aviation industry, where the durability of the threaded connection affects passenger safety. Due to the design of the thread, the quality of its surface is assessed visually in industrial practice. The authors of this study decided to examine the surface topography of external threads made by turning on Inconel 718 shafts in order to confirm the visual evaluation, as well as to investigate the influence of such factors as cutting speed, turning direction and type of profile. Three types of contours were cut for the research: triangular, trapezoidal symmetrical and trapezoidal asymmetrical. Turning of each was carried out twice at cutting speeds v_c = 17 m/min and v_c = 30 m/min. On each of the threads, the side surface of the profile made in the direction of the insert feed and the opposite surface were examined. The surface texture parameters Sa, Sq, Sp, Sv, Sz, Ssk and Sku were determined and compared. It was noticed that the thread surfaces show a tendency to irregular roughness, which was confirmed by the analysis of the Sku and Ssk coefficients. The sides of the contours made in the direction of the insert feed are characterized by a higher roughness in relation to the opposite sides, which may result from high cutting forces and difficulties with chip evacuation. With the cutting speed being considered, lower values of Sa and Sq were obtained for v_c = 17 m/min, which differed from the visual assessment, proving its high subjectivity.

The aim of this study is first to determine the effect of the discharge energy on the surface microgeometry of aluminum samples created by electrical discharge machining (EDM). Secondly, an additional purpose is to demonstrate the differences between the geometric multiscale methods: length-, area-scale, and curvature. Eleven samples were manufactured using discharge energies ranging from 0.486 mJ to 1389.18 mJ and, subsequently, measured with focus variation microscopy. Standard ISO and multiscale parameters were calculated and used for surface discrimination and regression analysis. The results of linear, logarithmic, and exponential regression analyses revealed a strong correlation (R² > 0.9) between the geometrical features of the surface topography and the discharge energy. The approach presented in this paper shows that it is possible to shape surface microgeometry by changing the energy of electrical discharges, and these dependencies are visible in various scales of observation. The similarities of the results produced by curvature and length-scale methods were observed, despite the significant differences in the essence of those methods.

The investment casting method supported with 3D-printing technology, allows the production of unit castings or prototypes with properties most similar to those of final products. Due to the complexity of the process, it is very important to control the dimensions in the initial stages of the process. This paper presents a comparison of non-contact measurement systems applied for testing of photopolymer 3D-printed injection die used in investment casting. Due to the required high quality of the surface parameters, the authors decided to use the DPP (Daylight Polymer Printing) 3D-printing technology to produce an analyzed injection die. The X-ray CT, Structured blue-light scanner and focus variation microscope measurement techniques were used to avoid any additional damages to the injection die that may arise during the measurement. The main objective of the research was to analyze the possibility of using non-contact measurement systems as a tool for analyzing the quality of the surface of a 3D-printed injection die. Dimensional accuracy analysis, form and position deviations, defect detection, and comparison with a CAD model were carried out.

Background. This study aimed to determine the kinetic frictional force (FF) of the recently produced TiNbTaZrO (Gummetal) orthodontic wire and compare it to the widely used wires of stainless steel (SS), nickel-titanium (NiTi), cobalt-chromium (CoCr) and titanium-molybdenum (TiMo) alloys. Methods. Five types of 0.016″ × 0.022″ wires were ligated with elastic ligatures to 0.018″ × 0.025″ SS brackets. The dynamic FFs between the brackets and ligated wires were measured utilizing a specialized tensile tester machine. Prior sample sizes for different archwires were conducted using power analysis for the general linear models. The existence of significant differences in FF between examined materials was initially confirmed by the one-way analysis of variance (ANOVA) with further evidence of pairwise differences by Tukey’s Honest Significant Difference test. Results. The pairwise differences between means of kinetic FFs for NiTi, CoCr, and Gummetal wires were not statistically significant (adjusted p-value > 0.05). Stainless steel alloy presented the lowest FF values significantly different from other groups (adjusted p-value < 0.05). On the contrary, TiMo wires showed significantly greater FFs (adjusted p-value < 0.05) than other alloys. Conclusions. Gummetal orthodontic wire exhibits similar frictional resistance as NiTi and CoCr wires. Bendable TiNbTaZrO wire might be used for sliding mechanics due to its favorable frictional properties.

Contact stylus profilometry is the leading surface texture measuring method in many manufacturing industries. For years it has been unmatched in terms of accuracy and reliability. Advancements in technology have led to the improvements in profilometer design. A stylus can either have a built in...

The objective of this work is to study the geometric properties of surface topographies of hot-work tool steel created by electric discharge machining (EDM) using motif and multiscale analysis. The richness of these analyses is tested through calculating the strengths of the correlations between discharge energies and resulting surface characterization parameters, focusing on the most representative surface features—craters, and how they change with scale. Surfaces were created by EDM using estimated energies from 150 to 9468 µJ and measured by focus variation microscope. The measured topographies consist of overlapping microcraters, of which the geometry was characterized using three different analysis: conventional with ISO parameters, and motif and multiscale curvature tensor analysis. Motif analysis uses watershed segmentation which allows extraction and geometrically characterization of each crater. Curvature tensor analysis focuses on the characterization of principal curvatures and their function and their evolution with scale. Strong correlations (R² > 0.9) were observed between craters height, diameter, area and curvature using linear and logarithmic regressions. Conventional areal parameter related to heights dispersion were found to correlate stronger using logarithmic regression. Geometric characterization of process-specific topographic formations is considered to be a natural and intuitive way of analyzing the complexity of studied surfaces. The presented approach allows extraction of information directly relating to the shape and size of topographic features of interest. In the tested conditions, the surface finish is mostly affected and potentially controlled by discharge energy at larger scales which is associated with sizes of fabricated craters.

Experimental studies reveal that the simultaneous addition of zinc dialkyl dithiophosphates (ZDDPs) and multi-wall carbon nanotubes (MWCNTs) to a poly-alpha-olefin base oil strongly reduces wear. In this paper, it is shown that MWCNTs promote the formation of an anti-wear (AW) layer on the metal surface that is much thicker than what ZDDPs can create as a sole additive. More importantly, the nanotubes’ action is indirect, i.e., MWCNTs neither mechanically nor structurally strengthen the AW film. A new mechanism for this effect is also proposed, which is supported by detailed tribometer results, friction track 3D-topography measurements, electron diffraction spectroscopy (EDS), and Raman spectroscopy. In this mechanism, MWCNTs mediate the transfer of both thermal and electric energy released on the metal surface in the friction process. As a result, this energy penetrates more deeply into the oil volume, thus extending the spatial range of tribochemical reactions involving ZDDPs.