RGRomero César Gomes

Romero César Gomes

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Romero César Gomes has a total of 23 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Feasibility of Using Sugar Cane Bagasse Ash in Partial Replacement of Portland Cement Clinker

    by Sâmara França, Leila Nóbrega Sousa, Sérgio Luiz Costa Saraiva, Maria Cecília Novaes Firmo Ferreira, Marcos Vinicio de Moura Solar Silva, Romero César Gomes, Conrado de Souza Rodrigues, Maria Teresa Paulino Aguilar, Augusto Cesar da Silva Bezerra

    This work presents a technical and economic study using sugar cane bagasse ash (SCBA) to partially replace Portland cement clinker. To evaluate the technical viability, the replacement rates of 10, 20, and 30% of Portland cement were used in the experiments. The ashes used were in the following conditions: (i) as collected (AC), (ii) ground (G), and (iii) re-burnt and ground (RG). Three composition parameters were used in the mortar mix procedures: (i) mix with water factor/fixed binder in volume, (ii) mix with water factor/fixed binder in weight, and (iii) mix with the fixed flow. After the technical feasibility analysis, the benefit of the substitutions and an analysis of the relationship between cement consumption and the acquired compressive strength, correlating with possible economic costs, were discussed. SCBA AC was not suitable for the partial replacement of Portland cement clinker. SCBA G presented a satisfactory performance and SCBA RG was the ash that presented the best performance in the partial replacement of Portland cement clinker. For the same levels of compressive strength, the consumption of Portland cement per cubic meter of concrete reduced; from this, the cost of concrete and mortar could be reduced by 8%, with the ash having the same value as cement. Furthermore, the use of SCBA RG at 30% inhibited the alkali–silica reaction (ASR) in concretes with a reactive basalt and quartzite aggregate. SCBA G (20 and 30%) and SCBA RG (10 and 20%) inhibited the ASR in concretes with a reactive basalt aggregate and reduced the expandability in concretes with a reactive quartzite aggregate. Another point to highlight was the durability shown by the cements with SCBA, which, 900 days after the accelerated test of expansion by the alkali–aggregate reaction, maintained high levels of flexural strength when compared to the results obtained before the accelerated test of expansion. The present work concluded that using sugar cane bagasse ash to replace Portland cement is feasible from a technical, environmental, and economic perspective.


  • GAMAH-R: a new mining rock slope classification system

    by Flávio Affonso Ferreira Ferreira Filho, Romero César Gomes, Teófilo Aquino Vieira da Costa


  • Open Access

    AVALIAÇÃO DA ERODIBILIDADE DE DIFERENTES HORIZONTES EM LATOSSOLOS POR MEIO DA RESISTÊNCIA NÃO DRENADA EM CAMPO: ESTUDO DE CASO NA REGIÃO DO QUADRILÁTERO FERRÍFERO –MG

    by Bruno de Oliveira Costa Couto, Romero César Gomes, Lucas Deleon Ferreira

    A erosão é um processo natural de modelagem do relevo que sofre influência de diversos fatores. Dentre estes, as características específicas solo tem grande influência, propriedade chamada de erodibilidade. A maioria das metodologias para estimativa da erodibilidade contempla critérios determinados em laboratório e em campo, não havendo consenso para sua determinação, se tornando muito moroso em alguns casos. O presente trabalho aborda a erodibilidade em taludes de corte rodoviários, com a presença de horizontes com comportamento antagônicos entre si em relação a erosão. Para análise da erodibilidade foram realizados ensaios de caracterização em laboratório e a determinação de resistência ao cisalhamento em campo, por meio de mini vane test, sendo os resultados posteriormente correlacionados com o fator K de erodibilidade determinado com uso de metodologias indiretas. A erodibilidade mostrou relação expressiva com a resistência ao cisalhamento, onde horizontes suscetíveis à erosão possuem menores valores, reflexo direto de um conjunto de propriedades do solo, principalmente granulometria, plasticidade e teor de matéria orgânica. Por meio de análise de variância foi possível diferenciar os solos erodíveis dos não erodíveis, sendo que estes resultados também apresentaram correlação negativa significativa com o fator de erodibilidade. Portanto, a metodologia se mostrou promissora para estimar o potencial erodível de solos em campo.


  • Open Access

    Reliability and geotechnical safety applied to deep foundations in precast concrete piles - case study

    by Armando Belato Pereira, Thiago Bomjardim Porto, Romero César Gomes

    The Brazilian standard pertinent to the design and execution of foundations, NBR 6122/2019, establishes that the safety inspection of foundations of a given project must be conducted based on compliance with specified safety factors. Safety factor verification is imperative to meet regulatory requirements; however, it is not enough to guarantee the safety of a foundation. As there is variability in the resistance and solicitation of the piles that make up a foundation, each safety factor value reflects a failure probability. Therefore, it is fictitious that the use of an adequate safety factor value implies the absence of failure risk. Thus, a reliability analysis, applied to a real building with an access ramp whose foundations are composed of precast concrete piles, based on the probabilistic moments, mean, and coefficient of variation, associated with the variability of pile resistance and solicitation, is presented in this article. The values obtained for the safety factors (2.14 and 1.98 for the building and the ramp foundations, respectively) and failure probabilities (1:2,244 and 1:3,131 for the building and the ramp foundations, respectively) implies that the project in question has an acceptable safety level. This article allows us to conclude that a small variation in the reliability index results in a large variation in failure probability; that a greater global safety factor does not necessarily lead to a lower failure probability and it becomes evident that this reliability analysis is a practical way, to manage the uncertainties inherent in foundation design, allowing rational decision making regarding performance.


  • Open Access

    Forecasting bearing capacity performance with semi-empirical and theoretical methods applied to precast concrete piles founded on sandy clay in the region of Uberlândia-MG, Brazil

    by Armando Belato Pereira, Thiago Bomjardim Porto, Romero César Gomes, Raphael Lucio Reis dos Santos, João Marcos Guimarães Rabelo

    This article presents a study on the performance of semi-empirical methods based on the Standard Penetration Test (SPT) for the prediction of bearing capacity already disseminated in the practice of Brazilian Foundation Engineering (Aoki and Velloso, 1975; Décourt and Quaresma, 1978, 1996; Teixeira,1996), together with the recent method proposed by Pereira (2020), and the theoretical method known as a Method (disseminated around the world). These were applied to precast concrete piles based on sandy clay in the Uberlândia-MG region. In the performance analysis, the ultimate shaft and tip resistances and the bearing capacity values, which were utilized as references, were mobilized in the dynamic loading tests performed on ten piles. The results of these tests were compared with those obtained using the mentioned methods. In general, both methods yielded robust results, with relatively accurate predictions, except the a Method, which was found to perform below the semi-empirical methods considered. The research still highlights the need for discretion in the application of semi-empirical/theoretical methodologies because there are certain scenarios wherein these methods can yield inaccurate results.


  • Open Access

    Obtaining geotechnical parameters from correlations between geophysics and CPT tests in tailings dams

    by Gustavo Marçal Sousa, Romero César Gomes

    This article introduces a hassle-free methodology for geotechnical parameters to be obtained from correlations between geophysics and CPT field tests in tailings dams undergoing the decommissioning process, which are reasonably representative of site conditions, from the very early project stages, with extensive coverage of all impoundment parts, without the requirement for large-size drilling programs. The development methodology consists of running direct (CPT) and indirect (geophysics) tests within the same area of the tailings dam to be decommissioned, with information crosschecking, thus allowing for results to be presented as adjustment equations, capable of describing tailings undrained shear strength based on geophysical survey data. A dam within the region known as Iron Quadrangle, in the state of Minas Gerais, Brazil, was selected to pilot the tests. The results obtained showed consistent adjustments, thus validating the proposed methodology as a complementary geotechnical investigation tool, and also enabling an optimized investigation plan to be proposed for similar tailings dams undergoing a mining process, so as to provide better assessment of the safety conditions of the proposals for deactivation with reduced schedule and resource savings.


  • Open Access

    RESTAURAÇÃO DE ESTRUTURA EM MADEIRA DA IGREJA NOSSA SENHORA DO CARMO EM DIAMANTINA – MG: ESTUDO DE CASO [ Restoration of wooden structure of Nossa Senhora do Carmo church in Diamantina – MG: Case study ]

    by Ana Clara dos Anjos Torres, Thiago Bomjardim Porto, Antônio Pires Azevedo Junior, Romero Cesar Gomes

    RESUMO: O estado de Minas Gerais possui o maior acervo artístico do barroco nacional, destacando os casarões e igrejas dos municípios históricos. Visto a importância histórica e cultural de tais edificações, torna-se necessária a restauração de seus elementos estéticos e funcionais, tais como as estruturas de madeira, em sua maioria. O objetivo deste trabalho é sequenciar as etapas de elaboração de projetos de restauração e recuperação de estruturas de madeira. E, como estudo de caso, apresentar a obra de restauração da Igreja Nossa Senhora do Carmo, em Diamantina, indicando o diagnóstico de suas patologias e a proposta para a intervenção. Foi necessário tratar quimicamente as superfícies contra infestações de insetos xilófagos e substituir parte da estrutura por madeira nova tratada, ancorada em nova fundação em concreto armado. Este reforço foi imprescindível para a estabilidade estrutural da Igreja, mesmo alterando parte do ambiente. Conclui-se que a escolha da técnica de recuperação de estruturas de madeira é condicionada por se tratar de uma restauração. É destacado também que as limitações de um projeto de restauração impedem, muitas vezes, o atendimento à normalização técnica quanto aos carregamentos e dimensionamento de estruturas. A técnica utilizada em Diamantina pode ser aprimorada para casos semelhantes e futuros estudos são importantes para a apresentação de metodologias menos destrutivas. The state of Minas Gerais has the largest artistic heritage of the national baroque, highlighting the mansions and churches of the historical municipalities. Because of the historical and cultural importance of such buildings, it is necessary to restore their aesthetic and functional elements, such as the wooden structures, in the majority. This work aims to sequence the stages of projects of restoration and recovery of wooden structures. As a case study, presents the restoration work of the Nossa Senhora do Carmo Church, in Diamantina, diagnosing its pathologies and proposing the intervention. It was necessary to chemically treatment against xylophagous insects infestations and replace part of the structure with new treated wood, anchored in a new foundation made of reinforced concrete. This reinforcement was indispensable for the structural stability of the Church, even changing part of the environment. It is concluded that the choice of the technique of recovery of wood structures is conditioned by the fact that it is a restoration. It is also emphasized that the limitations of a restoration project often prevent the obedience of technical normalization regarding the loading and dimensioning of structures. The technique used in Diamantina can be improved for similar cases and future studies are important for the presentation of less destructive methodologies.


  • Laboratory Evaluation of Electrokinetic Dewatering of Bauxite Tailings

    by L. De Leon Ferreira, Romero C. Gomes

    The mining tailings disposal system is often associated to the construction of large retaining systems, either for the great volume of materials generated by industrial plants or for the impossibility or difficulty of grants for new disposal areas. Due to increasing demand, these impoundments have become much more significant, triggering considerable increase of risk associated to them. In this context, new techniques must be developed aiming to decrease the volume of tailings produced and the optimization of disposal systems for these materials, particularly in terms of systems including tailings dewatering techniques. An alternative solution consists in dewater and consolidate mine tailings under current intermittence, technique called electroosmosis. This paper presents the development of an electroosmotic cell to measure the electrokinetic flow and the consolidation process of fine tailings under specified boundary conditions. The tailings are generated by the process of treatment of bauxite from BPM (Bauxita Paragominas Mining/Brazil), which consist of fine-grained materials, with initial solid content of 31%. The results of this experimental study are analyzed and discussed based on the principles of electrokinetic theory and has shown that the proposed technique would significantly accelerate the consolidation process of fine tailings (an average solid content of 58% was reached, within a 12-hour period), besides providing adequate design parameters for field applications.