Amr Y. Elbanhawy
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Amr Y. Elbanhawy has a total of 28 co-authors. Here are the top co-authors by number of shared publications:
M. Abo El-Nasr
3 shared publications- Jana Schultz
Hamburg University of Technology (TUHH), Institute of Environmental Technology and Energy Economics (IUE), Eissendorfer Strasse 40, 21073 Hamburg, Germany
2 shared publications Mahmoud Abo El-Nasr
2 shared publications- Mohamed Atef Kamel2 shared publications
Adel Elsabbagh
Professor, Dept. of Design and Production, Ain Shams Univ., Cairo 11517, Egypt
1 shared publicationAhmed Abdelkader
1 shared publication
Latest Publications
- Open Access
- 20 June 2026
- Published by Elsevier in Ain Shams Engineering Journal
- Vol. 17 (8)
Health under heat: assessment of overheating in Cairo’s low- income housing
- 20 June 2026
- Published by Elsevier in Ain Shams Engineering Journal
- Vol. 17 (8)
Open AccessHealth under heat: assessment of overheating in Cairo’s low- income housing
- Open Access
- 10 March 2026
- Published by Elsevier in SSRN Electronic Journal
A Systems-Integrated Framework for Green Hydrogen Deployment in Egypt: Hybrid Petri Net Operations, Atlas-Based Renewable Siting, and a Unified Techno-Economic-Environmental Scoring Model
This study presents a systems‑based planning framework for large‑scale green hydrogen production powered by commercially viable wind and solar technologies. We integrate atlas‑based resource mapping with Hybrid Petri Net operational modelling to capture both continuous energy flows and discrete events (start‑ups, failures, switching), enabling hour‑by‑hour simulation of electrolyser duty, desalination supply, storage dispatch, and delivery to demand centers. On the techno‑economic side, we evaluate levelized cost of hydrogen (LCOH), internal rate of return, profitability, annual output, and a System Availability Index that quantifies year‑round supply reliability. On the environmental side, we complete a cradle‑to‑grave accounting of greenhouse‑gas emissions, water demand (including desalination), and land occupation for generation, conversion, and transport assets. These dimensions are synthesized in a unified Techno‑Economic‑Environmental Score (TEES) to reveal deployment options that are technically feasible, commercially grounded, and sustainability‑aware.The framework is applied to five designated renewable‑energy zones in Egypt, comparing wind‑only, solar‑only, and hybrid configurations, hydrogen pipelines versus HVDC corridors, and the role of hydrogen storage in stabilizing supply. Results show that wind‑dominant coastal systems achieve leading unit economics and smaller environmental footprints, while inland solar‑dominant mega‑clusters unlock high production potential but require careful management of land and water intensity. Sensitivity analyses identify robust design envelopes and actionable heuristics for siting, corridor selection, and storage sizing.Overall, the work delivers novel, comprehensive insights for scaling renewable‑based hydrogen systems by combining rigorous operations modelling with techno‑economic and environmental evaluation grounded in commercially deployable renewable technologies.
- 10 March 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessA Systems-Integrated Framework for Green Hydrogen Deployment in Egypt: Hybrid Petri Net Operations, Atlas-Based Renewable Siting, and a Unified Techno-Economic-Environmental Scoring Model
This study presents a systems‑based planning framework for large‑scale green hydrogen production powered by commercially viable wind and solar technologies. We integrate atlas‑based resource mapping with Hybrid Petri Net operational modelling to capture both continuous energy flows and discrete events (start‑ups, failures, switching), enabling hour‑by‑hour simulation of electrolyser duty, desalination supply, storage dispatch, and delivery to demand centers. On the techno‑economic side, we evaluate levelized cost of hydrogen (LCOH), internal rate of return, profitability, annual output, and a System Availability Index that quantifies year‑round supply reliability. On the environmental side, we complete a cradle‑to‑grave accounting of greenhouse‑gas emissions, water demand (including desalination), and land occupation for generation, conversion, and transport assets. These dimensions are synthesized in a unified Techno‑Economic‑Environmental Score (TEES) to reveal deployment options that are technically feasible, commercially grounded, and sustainability‑aware.The framework is applied to five designated renewable‑energy zones in Egypt, comparing wind‑only, solar‑only, and hybrid configurations, hydrogen pipelines versus HVDC corridors, and the role of hydrogen storage in stabilizing supply. Results show that wind‑dominant coastal systems achieve leading unit economics and smaller environmental footprints, while inland solar‑dominant mega‑clusters unlock high production potential but require careful management of land and water intensity. Sensitivity analyses identify robust design envelopes and actionable heuristics for siting, corridor selection, and storage sizing.Overall, the work delivers novel, comprehensive insights for scaling renewable‑based hydrogen systems by combining rigorous operations modelling with techno‑economic and environmental evaluation grounded in commercially deployable renewable technologies.
- 24 October 2025
- Published by Elsevier in Bioresource Technology
- Vol. 441, 133545
A first order methodology for the sizing and siting of utility-scale biogas plants processing Egypt’s lignocellulosic biomass
- 24 October 2025
- Published by Elsevier in Bioresource Technology
- Vol. 441, 133545
A first order methodology for the sizing and siting of utility-scale biogas plants processing Egypt’s lignocellulosic biomass
- Open Access
- 17 June 2025
- Published by Springer Nature in BioEnergy Research
- Vol. 18 (1) , 1-16
Long-Term Continuous Anaerobic Co-digestion of Residual Biomass—Model Validation and Model-Based Investigation of Different Carbon-to-Nitrogen Ratios
Major challenges in using lignocellulosic residues as biogas substrates arise from their high diversity and their typically low nitrogen content, which may not provide sufficient nitrogen for the microorganisms. To investigate to what extent such substrates can be used in biogas plants without extensive pre-treatment, this study presents a 300-day continuous co-digestion of lignocellulosic substrates (i.e., sugarcane reed, lemon, and grape leaves) and goat manure while continuously monitoring various process parameters. The results suggest a stable and effective biogas production at a carbon-to-nitrogen ratio (C/N ratio) of 33, with a production of 244 ± 15 mLN gVS −1 d−1 biogas. At a higher C/N ratio of 43, the process remained stable, but hindrance was encountered. Process failure occurred at a C/N ratio of 52, where a rapid decline in biogas production was observed, accompanied by an increase in the volatile fatty acids to total alkalinity ratio (from < 0.2 to 0.9), a drop in the pH-value (from > 7 to 5.4), and an increased CO2-content of the provided biogas (from > 50% to 43%). The compositional analysis of the digestate suggests an insufficient N-supply and a failure of the carbonate and ammonium buffer systems inside the reactor. The experiment also served to validate a previously developed model based on the individual substrates’ degradation kinetics. With a relative root mean square error rRMSE of 8%, the model adequately predicted biogas production within defined limits. However, it could not anticipate process breakdown at high C/N ratios, highlighting a strong limitation. Graphical Abstract
- 17 June 2025
- Published by Springer Nature in BioEnergy Research
- Vol. 18 (1) , 1-16
Open AccessLong-Term Continuous Anaerobic Co-digestion of Residual Biomass—Model Validation and Model-Based Investigation of Different Carbon-to-Nitrogen Ratios
Major challenges in using lignocellulosic residues as biogas substrates arise from their high diversity and their typically low nitrogen content, which may not provide sufficient nitrogen for the microorganisms. To investigate to what extent such substrates can be used in biogas plants without extensive pre-treatment, this study presents a 300-day continuous co-digestion of lignocellulosic substrates (i.e., sugarcane reed, lemon, and grape leaves) and goat manure while continuously monitoring various process parameters. The results suggest a stable and effective biogas production at a carbon-to-nitrogen ratio (C/N ratio) of 33, with a production of 244 ± 15 mLN gVS −1 d−1 biogas. At a higher C/N ratio of 43, the process remained stable, but hindrance was encountered. Process failure occurred at a C/N ratio of 52, where a rapid decline in biogas production was observed, accompanied by an increase in the volatile fatty acids to total alkalinity ratio (from < 0.2 to 0.9), a drop in the pH-value (from > 7 to 5.4), and an increased CO2-content of the provided biogas (from > 50% to 43%). The compositional analysis of the digestate suggests an insufficient N-supply and a failure of the carbonate and ammonium buffer systems inside the reactor. The experiment also served to validate a previously developed model based on the individual substrates’ degradation kinetics. With a relative root mean square error rRMSE of 8%, the model adequately predicted biogas production within defined limits. However, it could not anticipate process breakdown at high C/N ratios, highlighting a strong limitation. Graphical Abstract
- 7 September 2021
- Published by Springer Nature in Journal of Failure Analysis and Prevention
- Vol. 21 (5) , 1808-1820
Assessment of Cooling Water and Spacing Sensitivities for Fire Propagation Prevention in Cylindrical Fuel Tank Farms
- 7 September 2021
- Published by Springer Nature in Journal of Failure Analysis and Prevention
- Vol. 21 (5) , 1808-1820
Assessment of Cooling Water and Spacing Sensitivities for Fire Propagation Prevention in Cylindrical Fuel Tank Farms
- 1 September 2020
- Published by American Society of Civil Engineers (ASCE) in Journal of Aerospace Engineering
- Vol. 33 (5) , 04020061
Testing of the Aerodynamic Characteristics of an Inflatable Airfoil Section
Inflatable structures are characterized by being light and easy to manufacture and deploy. Hence, they find many applications in aerospace and aeronautical engineering. In this paper, an inflatable segment with a The National Advisory Committee for Aeronautics (NACA) 0021 airfoil cross-section is designed, fabricated, and tested. The geometrical accuracy of the manufactured inflatable segment is measured using laser scanning. Measurements show that the average normalized error of the chord length and thickness are 2.97% and 0.554%, respectively. The aerodynamic behavior of the inflatable segment is then tested in a wind tunnel at different wind speeds and angles of attack. Lift forces are measured using a six-component balance, while the drag forces are calculated from the wake measurements. The lift and drag coefficients of the inflatable section are compared to those of a standard NACA 0021 airfoil. Finally, flow visualization is examined at different angles of attack using two methods: smoke and tufts. Both methods show that flow separation starts at 15° and full stall occurs at 25°. Results indicate that inflatables can find more applications in the design and construction of aerodynamic structures, such as wings.
- 1 September 2020
- Published by American Society of Civil Engineers (ASCE) in Journal of Aerospace Engineering
- Vol. 33 (5) , 04020061
Testing of the Aerodynamic Characteristics of an Inflatable Airfoil Section
Inflatable structures are characterized by being light and easy to manufacture and deploy. Hence, they find many applications in aerospace and aeronautical engineering. In this paper, an inflatable segment with a The National Advisory Committee for Aeronautics (NACA) 0021 airfoil cross-section is designed, fabricated, and tested. The geometrical accuracy of the manufactured inflatable segment is measured using laser scanning. Measurements show that the average normalized error of the chord length and thickness are 2.97% and 0.554%, respectively. The aerodynamic behavior of the inflatable segment is then tested in a wind tunnel at different wind speeds and angles of attack. Lift forces are measured using a six-component balance, while the drag forces are calculated from the wake measurements. The lift and drag coefficients of the inflatable section are compared to those of a standard NACA 0021 airfoil. Finally, flow visualization is examined at different angles of attack using two methods: smoke and tufts. Both methods show that flow separation starts at 15° and full stall occurs at 25°. Results indicate that inflatables can find more applications in the design and construction of aerodynamic structures, such as wings.
- 7 March 2019
- Published by Taylor & Francis in Drying Technology
- Vol. 38 (4) , 495-505
Granular transport through flighted rotary drums operated at optimum-loading: Mathematical model
This paper discusses the transport of granular materials through flighted rotary drums operated at the optimum loading. A mathematical model is derived from the force balance acting on a single traveling particle, to predict the mean residence time of transportation. Based on the available parameters of mean height of falling curtains and final discharge angle, this model can be helpful to estimate the appropriate solid feeding rate. Two steps were followed to implement the use of the model. Firstly, experiments were carried out on a batch rotary drum to obtain the needed input parameters. Then, a case study of a small capacity rotary dryer was considered. In both steps, the drum was operated at the optimum loading. The model results were compared with other correlation from the literature for two cases of solid and air flows: con-current and counter current. Based on the results, a factor is introduced for generalized correlation from literature.
- 7 March 2019
- Published by Taylor & Francis in Drying Technology
- Vol. 38 (4) , 495-505
Granular transport through flighted rotary drums operated at optimum-loading: Mathematical model
This paper discusses the transport of granular materials through flighted rotary drums operated at the optimum loading. A mathematical model is derived from the force balance acting on a single traveling particle, to predict the mean residence time of transportation. Based on the available parameters of mean height of falling curtains and final discharge angle, this model can be helpful to estimate the appropriate solid feeding rate. Two steps were followed to implement the use of the model. Firstly, experiments were carried out on a batch rotary drum to obtain the needed input parameters. Then, a case study of a small capacity rotary dryer was considered. In both steps, the drum was operated at the optimum loading. The model results were compared with other correlation from the literature for two cases of solid and air flows: con-current and counter current. Based on the results, a factor is introduced for generalized correlation from literature.