Halida Yunita
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Halida Yunita has a total of 22 co-authors. Here are the top co-authors by number of shared publications:
Munirwansyah Munirwansyah
Universitas Syiah Kuala
3 shared publications- Azmeri Azmeri
Universitas Syiah Kuala, Engineering Faculty, Civil Engineering Department, Syech Abdur-Rauf No. 7 Darussalam, 23111, Banda Aceh, Indonesia
2 shared publications - Faris Zahran Jemi
Universitas Syiah Kuala, Engineering Faculty, Electrical Engineering Department, Banda Aceh, Indonesia
2 shared publications Azmeri Azmeri
1 shared publicationBambang Setiawan
Program Study of Geological Engineering, Faculty of Engineering, Universitas Syiah Kuala
1 shared publicationDevi Sundary
Civil Engineering Department, Faculty of Engineering, Universitas Syiah Kuala
1 shared publication
Latest Publications
- Open Access
- 1 April 2026
- Published by LPPM Unsyiah in International Journal of Disaster Management
- Vol. 9 (1) , 54-68
Slope instability and sediment contribution during drawdown: Implications for sediment management and disaster risk in Keuliling Reservoir, Indonesia
Slope instability along reservoir banks is an important but often overlooked source of sediment entering reservoirs during water-level fluctuations. Previous sedimentation assessments in Keuliling Reservoir mainly considered watershed erosion and did not explicitly quantify the contribution of reservoir-bank slope failures. This study investigates the potential sediment contribution from unstable reservoir slopes induced by water-level drawdown. Field observations, soil sampling, and laboratory shear tests were conducted in three landslide-prone zones around the Keuliling Reservoir, Aceh Province. Slope stability was evaluated using a limit equilibrium framework under different water-level drawdown scenarios ranging from 0.2 to 2.4 m. The results indicate that slope stability decreases significantly as water levels decline. Zones A and C exhibit unstable conditions with average safety factors of 0.52 and 0.99, respectively, while Zone B remains relatively stable with an average safety factor of 2.92. Potential sediment contribution from unstable slopes was estimated using a sediment transport approximation adapted from classical bed-load theory to represent possible mobilized material during slope failure. The analysis shows that reservoir drawdown can substantially increase slope instability and may contribute additional sediment to the reservoir storage. These findings highlight the importance of incorporating reservoir-bank instability into sediment management, operational decision-making, and disaster risk reduction strategies in reservoir systems. The results provide useful insights for reservoir operation planning, particularly in establishing safer drawdown rates and slope monitoring strategies.
- 1 April 2026
- Published by LPPM Unsyiah in International Journal of Disaster Management
- Vol. 9 (1) , 54-68
Open AccessSlope instability and sediment contribution during drawdown: Implications for sediment management and disaster risk in Keuliling Reservoir, Indonesia
Slope instability along reservoir banks is an important but often overlooked source of sediment entering reservoirs during water-level fluctuations. Previous sedimentation assessments in Keuliling Reservoir mainly considered watershed erosion and did not explicitly quantify the contribution of reservoir-bank slope failures. This study investigates the potential sediment contribution from unstable reservoir slopes induced by water-level drawdown. Field observations, soil sampling, and laboratory shear tests were conducted in three landslide-prone zones around the Keuliling Reservoir, Aceh Province. Slope stability was evaluated using a limit equilibrium framework under different water-level drawdown scenarios ranging from 0.2 to 2.4 m. The results indicate that slope stability decreases significantly as water levels decline. Zones A and C exhibit unstable conditions with average safety factors of 0.52 and 0.99, respectively, while Zone B remains relatively stable with an average safety factor of 2.92. Potential sediment contribution from unstable slopes was estimated using a sediment transport approximation adapted from classical bed-load theory to represent possible mobilized material during slope failure. The analysis shows that reservoir drawdown can substantially increase slope instability and may contribute additional sediment to the reservoir storage. These findings highlight the importance of incorporating reservoir-bank instability into sediment management, operational decision-making, and disaster risk reduction strategies in reservoir systems. The results provide useful insights for reservoir operation planning, particularly in establishing safer drawdown rates and slope monitoring strategies.
- Open Access
- 31 March 2022
- Published by Institute of Postgraduate Studies, Syiah Kuala University in Aceh International Journal of Science and Technology
- Vol. 11 (1) , 1-11
Spatially Distribution of Soil Ultimate Bearing Capacity at Singkil-Aceh Based on a Static Cone Penetration Test
The Singkil Sub-district of Aceh Singkil District comprises alluvium deposits with a relatively low ultimate bearing capacity. The ultimate bearing capacity of the soil is closely related to the safety of a building. The important thing related to estimating the ultimate bearing capacity of the soil is in-situ soil investigation. This study aims to estimate the spatial distribution of soil ultimate bearing capacity using field test data in the Singkil Sub-district. Estimating ultimate bearing capacity is useful to provide an initial picture for various planning and infrastructure development activities in the study area. Twenty CPT in-situ tests have been obtained from various field works in Aceh Singkil Regency. Field data analysis, based on empirical methods, was carried out to obtain the value of the ultimate bearing capacity of the soil at the test location. Then, the estimated distribution of the maximum bearing capacity obtained was carried out. The zoning map of the distribution of soil ultimate bearing capacity in the study was developed from this research. This map can be used as a form or effort of disaster mitigation by various stakeholders involved in planning and building various infrastructure facilities in the Singkil Sub-district
- 31 March 2022
- Published by Institute of Postgraduate Studies, Syiah Kuala University in Aceh International Journal of Science and Technology
- Vol. 11 (1) , 1-11
Open AccessSpatially Distribution of Soil Ultimate Bearing Capacity at Singkil-Aceh Based on a Static Cone Penetration Test
The Singkil Sub-district of Aceh Singkil District comprises alluvium deposits with a relatively low ultimate bearing capacity. The ultimate bearing capacity of the soil is closely related to the safety of a building. The important thing related to estimating the ultimate bearing capacity of the soil is in-situ soil investigation. This study aims to estimate the spatial distribution of soil ultimate bearing capacity using field test data in the Singkil Sub-district. Estimating ultimate bearing capacity is useful to provide an initial picture for various planning and infrastructure development activities in the study area. Twenty CPT in-situ tests have been obtained from various field works in Aceh Singkil Regency. Field data analysis, based on empirical methods, was carried out to obtain the value of the ultimate bearing capacity of the soil at the test location. Then, the estimated distribution of the maximum bearing capacity obtained was carried out. The zoning map of the distribution of soil ultimate bearing capacity in the study was developed from this research. This map can be used as a form or effort of disaster mitigation by various stakeholders involved in planning and building various infrastructure facilities in the Singkil Sub-district
- 9 March 2022
- Published by Polish Academy of Sciences Chancellery in Journal of Water and Land Development
- p. 108-118
Surface erosion hazard and sediment yield for Keuliling Reservoir in Indonesia
The construction of the Keuliling Reservoir aims to accommodate and utilise water for agricultural purposes. In this research, soil erosion modelling using the USLE method showed that the level of erosion hazard for each Keuliling Reservoir sub-watershed was classified into low-moderate. Land erosion occurred in the area around the reservoir inundation is the most significant contribution to the magnitude of erosion (38.62 Mg∙ha–1∙y–1. Based on the point of sediment sampling in the Keuliling reservoir, the sediment volume was 1.43 Mg∙m–3. So, the volumetric sediment input from the Keuliling reservoir watershed is 20.918,32 m3∙y–1. The degradation of reservoir function due to sedimentation can affect reservoir services. The ability to estimate the rate of watershed surface erosion and sediment deposition in the reservoir is vital for reservoir sustainability. Besides the land erosion in the Keuliling Reservoir, there are also other potential sources of erosion that can reduce the capacity of the reservoir, i.e. the rate of sedimentation from a reservoir cliff landslide. The USLE estimation results show that the soil erosion analysis provides important and systematic information about nature, intensity and spatial distribution in the watershed and sediment volume in the Keuliling Reservoir. This finding allows the identification of the most vulnerable areas and the type of erosion dominant for long-term land management.
- 9 March 2022
- Published by Polish Academy of Sciences Chancellery in Journal of Water and Land Development
- p. 108-118
Surface erosion hazard and sediment yield for Keuliling Reservoir in Indonesia
The construction of the Keuliling Reservoir aims to accommodate and utilise water for agricultural purposes. In this research, soil erosion modelling using the USLE method showed that the level of erosion hazard for each Keuliling Reservoir sub-watershed was classified into low-moderate. Land erosion occurred in the area around the reservoir inundation is the most significant contribution to the magnitude of erosion (38.62 Mg∙ha–1∙y–1. Based on the point of sediment sampling in the Keuliling reservoir, the sediment volume was 1.43 Mg∙m–3. So, the volumetric sediment input from the Keuliling reservoir watershed is 20.918,32 m3∙y–1. The degradation of reservoir function due to sedimentation can affect reservoir services. The ability to estimate the rate of watershed surface erosion and sediment deposition in the reservoir is vital for reservoir sustainability. Besides the land erosion in the Keuliling Reservoir, there are also other potential sources of erosion that can reduce the capacity of the reservoir, i.e. the rate of sedimentation from a reservoir cliff landslide. The USLE estimation results show that the soil erosion analysis provides important and systematic information about nature, intensity and spatial distribution in the watershed and sediment volume in the Keuliling Reservoir. This finding allows the identification of the most vulnerable areas and the type of erosion dominant for long-term land management.
- Open Access
- 29 December 2021
- Published by LPPM Unsyiah in Journal of The Civil Engineering Student
- Vol. 3 (3) , 294-300
Analisis Daya Dukung Pondasi Tiang Pancang Dengan Metode Formula Dinamis Pada Jembatan Nasional Alue Lamteh - Aceh
Jembatan merupakan sebuah konstruksi yang terdiri dari struktur atas dan struktur bawah yang berfungsi untuk menghubungkan dua ruas jalan yang terputus akibat adanya rintangan yang lebih rendah seperti sungai dan lainnya. Objek yang menjadi tinjauan penelitian ini adalah Proyek Pelebaran Jembatan Alue Lamteh. Jembatan Alue Lamteh merupakan jembatan yang berlokasi di Desa Keumireu, Kecamatan Kuta Cot Glie, Kabupaten Aceh Besar pada titik koordinat 5°23’42,4” LU dan 95°29’35,9” BT. Tujuan penelitian ini adalah untuk menganalisis daya dukung dinamis pondasi tiang pancang pada Proyek Pelebaran Jembatan Alue Lamteh. Daya dukung dinamis tiang pancang dihitung menggunakan metode Janbu, ENR-Modified, CNB, PCUBC dan Hiley. Berdasarkan hasil perhitungan daya dukung dinamis didapat daya dukung terbesar yaitu menggunakan metode ENR-Modified pada tiang P1.2 dan P3.2 dengan s=12 mm masing-masing sebesar 83,488 ton sedangkan daya dukung terkecil yaitu menggunakan metode PCUBC pada tiang P2.2. dengan s=24 mm sebesar 35,470 ton.
- 29 December 2021
- Published by LPPM Unsyiah in Journal of The Civil Engineering Student
- Vol. 3 (3) , 294-300
Open AccessAnalisis Daya Dukung Pondasi Tiang Pancang Dengan Metode Formula Dinamis Pada Jembatan Nasional Alue Lamteh - Aceh
Jembatan merupakan sebuah konstruksi yang terdiri dari struktur atas dan struktur bawah yang berfungsi untuk menghubungkan dua ruas jalan yang terputus akibat adanya rintangan yang lebih rendah seperti sungai dan lainnya. Objek yang menjadi tinjauan penelitian ini adalah Proyek Pelebaran Jembatan Alue Lamteh. Jembatan Alue Lamteh merupakan jembatan yang berlokasi di Desa Keumireu, Kecamatan Kuta Cot Glie, Kabupaten Aceh Besar pada titik koordinat 5°23’42,4” LU dan 95°29’35,9” BT. Tujuan penelitian ini adalah untuk menganalisis daya dukung dinamis pondasi tiang pancang pada Proyek Pelebaran Jembatan Alue Lamteh. Daya dukung dinamis tiang pancang dihitung menggunakan metode Janbu, ENR-Modified, CNB, PCUBC dan Hiley. Berdasarkan hasil perhitungan daya dukung dinamis didapat daya dukung terbesar yaitu menggunakan metode ENR-Modified pada tiang P1.2 dan P3.2 dengan s=12 mm masing-masing sebesar 83,488 ton sedangkan daya dukung terkecil yaitu menggunakan metode PCUBC pada tiang P2.2. dengan s=24 mm sebesar 35,470 ton.
- Open Access
- 1 November 2020
- Published by KEAI Publishing in Geodesy and Geodynamics
- Vol. 11 (6) , 455-467
A new empirical equation of shear wave velocity to predict the different peak surface accelerations for Jakarta city
- 1 November 2020
- Published by KEAI Publishing in Geodesy and Geodynamics
- Vol. 11 (6) , 455-467
Open AccessA new empirical equation of shear wave velocity to predict the different peak surface accelerations for Jakarta city
- 30 September 2020
- Published by Polish Academy of Sciences Chancellery in Journal of Water and Land Development
- p. 20-28
Physical vulnerability to flood inundation: As the mitigation strategies design
Flood with intense rainfall and inadequate drainage system leads to flood inundation in residential areas, which in turn damages the housing components and causes a loss. The different level of flood inundation at various affected locations caused varying degrees of losses. This study aimed to identify the damage conditions and analysed the physical loss of the residential building components. The physical vulnerability level is influenced by two damage qualification: the structural and architectural damages. The third-order polynomial function approach produces the best model for both qualifications, yielding the smallest average of errors (RMSE) of 0.0187 for the structural quality and 0.0672 for the architectural quality. The amount of losses related to the architectural elements of the house is smaller compared to the structural one as it is not its main component. This approach is useful as a guide in determining the post-flood handling rehabilitation cost of both structural and architectural elements that will be more appropriate for future conditions. This information is essential as effective management to design flood disaster mitigation strategies and may serve as a basis for flood risk management.
- 30 September 2020
- Published by Polish Academy of Sciences Chancellery in Journal of Water and Land Development
- p. 20-28
Physical vulnerability to flood inundation: As the mitigation strategies design
Flood with intense rainfall and inadequate drainage system leads to flood inundation in residential areas, which in turn damages the housing components and causes a loss. The different level of flood inundation at various affected locations caused varying degrees of losses. This study aimed to identify the damage conditions and analysed the physical loss of the residential building components. The physical vulnerability level is influenced by two damage qualification: the structural and architectural damages. The third-order polynomial function approach produces the best model for both qualifications, yielding the smallest average of errors (RMSE) of 0.0187 for the structural quality and 0.0672 for the architectural quality. The amount of losses related to the architectural elements of the house is smaller compared to the structural one as it is not its main component. This approach is useful as a guide in determining the post-flood handling rehabilitation cost of both structural and architectural elements that will be more appropriate for future conditions. This information is essential as effective management to design flood disaster mitigation strategies and may serve as a basis for flood risk management.
- Open Access
- 20 September 2019
- Published by LPPM Unsyiah in Jurnal Arsip Rekayasa Sipil dan Perencanaan
- Vol. 2 (3) , 258-267
ANALISIS PERENCANAAN BUKIT BUATAN (ESCAPE HILL) TERHADAP TINGGI RUN UP UNTUK TEMPAT EVAKUASI SEMENTARA
As we know, there is still a lack of the optimal effort for temporary evacuation sites to face the various threats of the earthquake which may caused the tsunami in the city of Banda Aceh. To deal with this serious threat, it is necessary to prepare a place of salvation to face the tsunami. In this case, it is an escape hill. The objective of this research is to determine the bearing capacity of the subgrade to the escape hill planning and the amount of the settlement, due to the load of the embankment height (Hcrit) and the value of the slope safety factor (FK). This research is conducted in Desa Deah Baro with the GCS coordinates (Geographic Coordinate System) 5º33'45.72"N 95º17'51.34"E which was calculated by using the Plaxis 8.2 computing system on the variations of the embankment height which started from the existing which is 2,0 m height, 4,0 m, 6,0 m, 8,0 m, 10 m and 12 m (run-up performance). As the results of analysis, the researcher found that the addition of the load due to the increase in soil embankment height has resulted in an increase in the value of settlement to the soil stability with an average percentage of 2,86% and the safety factor decreasing value (FK) numbers on slopes with an average percentage of 0,10%. At 2,0 m embankment heights, the researcher obtained a settlement value of 0,271 cm with the safety factor value (FK) is 1,684 greater than 1. Furthermore, with the embankment height of 4,0 m, there is a settlement of 1,139 cm dan safety factor (FK) 1,365 greater than 1. At a embankment height of 6.0 m there is a settlement of 3,035 cm and a safety factor (FK) 1,214 greater than 1. At embankment heights of 8,0 m, the settlement is 6,244 cm with a safety factor (FK) 1,135 greater than 1. For embankment heights of 10 m and 12 m, the decrease occurred was 10,991 cm and 17,446 cm with safety factor (FK) = 1,095 and 1,044~1. The occured decline was still within the tolerance limits, so that the subgrade was still able to withstand the embankment. The results of the value of the safety factor (FK) showed that the slope was safe and did not indicate the slope slides.
- 20 September 2019
- Published by LPPM Unsyiah in Jurnal Arsip Rekayasa Sipil dan Perencanaan
- Vol. 2 (3) , 258-267
Open AccessANALISIS PERENCANAAN BUKIT BUATAN (ESCAPE HILL) TERHADAP TINGGI RUN UP UNTUK TEMPAT EVAKUASI SEMENTARA
As we know, there is still a lack of the optimal effort for temporary evacuation sites to face the various threats of the earthquake which may caused the tsunami in the city of Banda Aceh. To deal with this serious threat, it is necessary to prepare a place of salvation to face the tsunami. In this case, it is an escape hill. The objective of this research is to determine the bearing capacity of the subgrade to the escape hill planning and the amount of the settlement, due to the load of the embankment height (Hcrit) and the value of the slope safety factor (FK). This research is conducted in Desa Deah Baro with the GCS coordinates (Geographic Coordinate System) 5º33'45.72"N 95º17'51.34"E which was calculated by using the Plaxis 8.2 computing system on the variations of the embankment height which started from the existing which is 2,0 m height, 4,0 m, 6,0 m, 8,0 m, 10 m and 12 m (run-up performance). As the results of analysis, the researcher found that the addition of the load due to the increase in soil embankment height has resulted in an increase in the value of settlement to the soil stability with an average percentage of 2,86% and the safety factor decreasing value (FK) numbers on slopes with an average percentage of 0,10%. At 2,0 m embankment heights, the researcher obtained a settlement value of 0,271 cm with the safety factor value (FK) is 1,684 greater than 1. Furthermore, with the embankment height of 4,0 m, there is a settlement of 1,139 cm dan safety factor (FK) 1,365 greater than 1. At a embankment height of 6.0 m there is a settlement of 3,035 cm and a safety factor (FK) 1,214 greater than 1. At embankment heights of 8,0 m, the settlement is 6,244 cm with a safety factor (FK) 1,135 greater than 1. For embankment heights of 10 m and 12 m, the decrease occurred was 10,991 cm and 17,446 cm with safety factor (FK) = 1,095 and 1,044~1. The occured decline was still within the tolerance limits, so that the subgrade was still able to withstand the embankment. The results of the value of the safety factor (FK) showed that the slope was safe and did not indicate the slope slides.