Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Anayansi Estrada-Monje has a total of 68 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    A Three-Dimensional Framework for Rational Ion Separation with Polymeric Membrane Systems

    by George Bess-Palacios, Guillermo González-Sánchez, Claudia Alejandra Hernández-Escobar, Claudia Ivone Piñón-Balderrama, Miguel Alonso Orozco-Alvarado, América Susana Mares-García, Anayansi Estrada-Monje, Erasto Armando Zaragoza-Contreras

    This review treats selective ion separation in polymeric membrane systems as a design problem rather than as a fixed material property. To address the gap between laboratory performance and process-level relevance, a three-dimensional analytical framework that integrates transport mechanism, dynamic structural state, and separation-matrix complexity is proposed. Five research streams are compared: polymer inclusion membranes, ion-exchange membranes and electrodialysis, nanostructured and subnanometric frameworks, composite architectures, and polymer inclusion membrane – electrodialysis (PIM-ED) hybrids. The comparison shows that selectivity is governed not only by the nominal membrane mechanism, but also by hydration-driven structural changes and by the complexity of the operating matrix. Overall, the framework provides a common basis for interpreting selectivity, comparing membrane families, and guiding rational design for ion-separation processes.


  • Open Access

    The Drop-In Delusion: Technical and Systemic Impacts of PLA Contamination on the HDPE Circular Economy

    by Anayansi Estrada-Monje, Sergio Alonso-Romero, Anayansi Zaragoza-Estrada, María Cristina Kantún-Uicab, Claudia Ivone Piñón-Balderrama, Claudia Alejandra Hernández-Escobar, Erasto Armando Zaragoza-Contreras

    The increasing use of biodegradable polymers, especially poly (lactic acid) (PLA), has raised concern about their entry into conventional post-consumer recycling streams. This review examines the technical and systemic consequences of PLA contamination in the high-density polyethylene (HDPE) circular economy through the “drop-in delusion,” defined here as the mistaken assumption that a sustainability-marketed polymer can enter an established recycling stream without compromising system compatibility. Focusing on contamination-sensitive conditions in which segregation, sorting, or stream purity are insufficient to prevent cross-contamination, the review discusses the immiscibility of HDPE/PLA blends and the resulting changes in stiffness, ductility, toughness, and aging behavior. It also analyzes mitigation routes such as improved sorting, compatibilization, and policy measures, while emphasizing that the practical severity of contamination depends on local infrastructure and contamination levels. In addition, it considers the risk that contaminated materials diverted into lower-value applications may become more vulnerable to interfacial damage, weathering, and secondary fragmentation. Overall, the review argues that circular-plastics strategies must distinguish biodegradability from recycling-system compatibility to protect the quality and value of HDPE recyclates.

  • Open Access

    DESARROLLO DE PRODUCTOS DE VIDA ÚTIL CORTA CON POLÍMEROS SOSTENIBLES

    by Anayansi Estrada Monje, María Maldonado Santoyo, Sergio Alonso-Romero, Erasto Armando Zaragoza-Contreras

    La investigación científica está enfocada a resolver los problemas prioritarios del país y a contribuir al cuidado del medio ambiente. En este sentido, los plásticos han contribuido enormemente a facilitar la vida de las personas. Sin embargo, la mala gestión de los residuos plásticos derivados del petróleo también ha provocado el aumento de la contaminación ambiental, por lo que ha sido necesario establecer acuerdos globales para reducir el consumo de plásticos de un solo uso. En este contexto el presente artículo se enfoca en el desarrollo de un biopolímero biodegradable que pueda utilizarse en sustitución de materiales de uso común derivados del petróleo, como polietileno y polipropileno, entre otros; y que sirva para la fabricación de diferentes productos de vida útil corta. El biopolímero que se desarrolló está basado en el uso de materias primas renovables, derivadas de plantas como el maíz y la yuca, mediante una modificación química que permita el procesamiento, mediante los métodos convencionales de transformación de plásticos, como la inyección o la extrusión. Se obtuvieron productos prototipo que dejan ver el potencial de aplicaciones de los materiales desarrollados.

  • Open Access

    High-Capacity Adsorption of a Cationic Dye Using Alkali-Activated Geopolymers Derived from Agricultural Residues

    by Claudia Alejandra Hernández-Escobar, América Susana Mares-García, Miguel Alonso Orozco-Alvarado, Alejandro Vega-Rios, Claudia Ivone Piñón-Balderrama, Anayansi Estrada-Monje, Erasto Armando Zaragoza-Contreras

    A geopolymer, derived from agricultural waste, was used as an efficient, sustainable, and low-cost adsorbent of methylene blue, a recurrent industrial dye contaminant. The geopolymer was synthesized via a standard alkali activation process using wheat husk ash calcinated at 1050 °C. Adsorption capabilities were evaluated through batch kinetic experiments. The removal efficiency was determined by ultraviolet–visible spectrophotometry, and the adsorption kinetics were fitted to various models. The geopolymer demonstrated a maximum adsorption capacity of 270.58 mg/g for methylene blue, achieving a removal efficiency of 85.20% under optimal conditions. Kinetic analysis confirmed that the adsorption process is best described by the pseudo-second-order model. This suggests that chemisorption, which involves chemical bonding or electron exchange between the dye and the negatively charged aluminosilicate structure of the geopolymer, is the rate-limiting mechanism. This demonstrates that geopolymers are effective and promising adsorbents, valorizing an agricultural waste stream into a functional material for the efficient treatment of dye-polluted wastewater. The competitive capacity and favorable chemisorption mechanism position the geopolymer as a promising material for the remediation of dye-contaminated industrial effluents.


  • Open Access

    Effects of Polylactic Acid Content, Reprocessing Cycles, and Aging Conditions on the Mechanical Properties of Recycled High‐Density Polyethylene

    by Javier Cruz-Salgado, Anayansi Estrada-Monje, Miroslava Alejandra Silva-Goujon, Sergio Alonso-Romero, Erasto Armando Zaragoza-Contreras

    The increasing incorporation of biodegradable plastics into conventional recycling streams has raised concerns regarding their influence on the performance of recycled polymers. In particular, the presence of polylactic acid (PLA) in recycled high‐density polyethylene (rHDPE) may significantly affect mechanical stability during reprocessing and environmental exposure. This study systematically evaluates the combined effects of PLA content (0–50 wt%), recycling cycles, exposure time, and aging conditions (natural and accelerated) on the mechanical performance of rHDPE/PLA blends using a multilevel full factorial experimental design comprising 96 experimental runs. Tensile stress, elongation at break, and impact resistance were measured according to ASTM standards. Statistical analyses including ANOVA, regression modeling, and interaction analysis were applied to identify significant factors and combined effects, followed by multiresponse optimization using a desirability‐function approach. PLA incorporation produced a drastic reduction in ductility and toughness, with elongation at break decreasing by more than 95% and impact resistance by approximately 80%–85% as PLA content increased from 0 to 50 wt%. Accelerated aging generated the most pronounced reduction in tensile strength, with decreases on the order of 20%–30% compared with natural aging conditions. Recycling cycles further contributed to mechanical degradation, although to a lesser extent. Significant interaction effects among composition, recycling cycle, and aging environment demonstrated that mechanical degradation results from synergistic thermo‐oxidative, processing‐induced, and interfacial incompatibility mechanisms. The results provide a comprehensive statistical framework for understanding the degradation behavior of rHDPE systems contaminated with biodegradable polymers and support the identification of optimal operating conditions for maximizing the mechanical performance of recycled polymer blends.

  • Open Access

    Intelligent Motion Classification via Computer Vision for Smart Manufacturing and Ergonomic Risk Prevention in SMEs

    by Armando Mares-Castro, Valentin Calzada-Ledesma, María Blanca Becerra-Rodríguez, Raúl Santiago-Montero, Anayansi Estrada-Monje

    The transition toward Industry 4.0 and the emerging concept of Industry 5.0 demand intelligent tools that integrate efficiency, adaptability, and human-centered design. This paper presents a Computer Vision-based framework for automated motion classification in Methods-Time Measurement 2 (MTM-2), with the aim of supporting industrial time studies and ergonomic risk assessment. The system uses a Convolutional Neural Network (CNN) for pose estimation and derives angular kinematic features of key joints to characterize upper limb movements. A two-stage experimental design was conducted: first, three lightweight classifiers—K-Nearest Neighbors (KNN), Support Vector Machines (SVMs), and a Shallow Neural Network (SNN)—were compared, with KNN demonstrating the best trade-off between accuracy and efficiency; second, KNN was tested under noisy conditions to assess robustness. The results show near-perfect accuracy (≈100%) on 8919 motion instances, with an average inference time of 1 microsecond per sample, reducing the analysis time compared to manual transcription. Beyond efficiency, the framework addresses ergonomic risks such as wrist hyperextension, offering a scalable and cost-effective solution for Small and Medium-sized Enterprises. It also facilitates integration with Manufacturing Execution Systems and Digital Twins, and is therefore aligned with Industry 5.0 goals.


  • Open Access

    Non-Enzymatic Electrochemical Sensing of Glucose with Silver Nanoparticles Supported on Poly(3-aminobenzoic acid)

    by América Susana Mares-García, Claudia Alejandra Hernández-Escobar, Sonia Kimberly Enriquez-Durán, Anayansi Estrada-Monje, Erasto Armando Zaragoza-Contreras, Claudia Ivone Piñón-Balderrama

    This study explores the development of a non-enzymatic electrochemical glucose sensor based on poly(3-aminobenzoic acid) (P3ABA) combined with silver nanoparticles (AgNPs). Incorporating AgNPs into the P3ABA matrix enhances the sensor’s electrocatalytic properties, leading to a system with greater stability. Cyclic voltammetry and chronoamperometry were employed to evaluate the sensor’s performance, demonstrating a sensitivity of 50.71 µA mM−1 cm−2 and a limit of detection (LOD) of 0.2 µM. The sensor exhibited a linear response over a broad concentration range (1 to 16 mM), with a coefficient of determination (R2) of 0.998, indicating good reproducibility and precision. These results highlight the potential of the P3ABA/AgNP composite for glucose sensing applications, offering an extended linear range, allowing for the quantification of glucose concentrations from very low to significantly high levels, covering both physiological and pathological conditions.


  • Open Access

    Evaluation of EPDM scrap/ natural fiber vulcanization by solvent swelling analysis

    by María Cristina Kantun-Uicab, Anayansi Estrada-Monje, Isis Rodríguez-Sánchez

    In the rubber industry there is an opportunity to reuse unvulcanized rubber scrap generated during the formulation process, as well as to find alternatives for its use. For this reason, in this work the characterization of EPDM/natural fiber scrap with different proportions is studied through rheological and swelling studies according to the Flory Rehner Equation. The solvents used were distilled water, cyclohexane and toluene at different exposure times. The results found allow us to conclude that the fiber content in EPDM rubber does not affect the scorch time, the maximum vulcanization time. In the case of swelling analysis, the observed changes had a maximum increase of approximately 3% when the fiber content in the composite material increased when they were exposed to water and toluene, this was attributed to the characteristics of the EPDM studied in this work.

  • Open Access

    Recycling of Bovine Hair Waste Through the Design of a Compatibilizing Agent for Sustainable Thermoplastic Starch-Untreated Bovine Hair Composites

    by Luz Elena Mora-Maldonado, Anayansi Estrada-Monje, Roberto Zitzumbo-Guzmán, Isis Rodríguez-Sánchez, Leonardo Baldenegro-Pérez, Claudia Ivone Piñón-Balderrama, Saddys Rodríguez-Llamazares, Erasto Armando Zaragoza-Contreras

    Bovine hair waste was chemically modified to obtain a coupling agent (CA) for the compatibilization of thermoplastic starch (TPS)-unmodified bovine hair waste (UH) composites. The composites processed with CA presented improved tensile strength (3.5 MPa) compared to TPS–UH composites without CA (1.25 MPa). An interaction mechanism to describe the improvement in mechanical properties and thermal stability was postulated based on Fourier-transform infrared spectroscopy (FTIR) and density functional theory (DFT). In addition, optical and electron microscopy showed that CA favored the adhesion of UH to TPS. Global results suggested the formation of a CA–UH network that interacts with the TPS matrix. Obtaining composites from waste from the tanning industry can contribute to the development of a more responsible and sustainable industry and represents an opportunity to reduce the environmental impact of one of the most important industries globally. It is worth mentioning that this research is aligned with the sustainable development goals (SDGs) proposed by the United Nations, which promotes sustainable industrialization and the promotion of innovation.

  • Open Access

    Effect of the Addition of PLA on the Thermal and Mechanical Properties of Reprocessed HDPE

    by Anayansi Estrada-Monje, Miroslava Alejandra Silva-Goujon, Isis Rodríguez-Sánchez, Alain Salvador Conejo-Dávila, Claudia Ivone Piñón-Balderrama, Anayansi Zaragoza-Estrada, Leonardo Aurelio Baldenegro-Pérez, Erasto Armando Zaragoza-Contreras

    Amid the current environmental crisis caused by plastic accumulation, one of the proposed solutions to manage this problem is using biodegradable polymers. However, the impact of adding biodegradable polymers to the well-established circular economy of recyclable polymers, such as HDPE, has not been fully considered. Therefore, there is a need to reconsider the way we consume, dispose of, and manage biodegradable polymers after use. This study evaluates the effect of varying the contents of a biodegradable polymer, taking poly(lactic acid) (PLA) as a model biodegradable polymer, on the thermal and mechanical properties of HDPE. The study highlights the importance of identifying and disposing of biodegradable polymers to avoid mixtures with HDPE, in order not to affect mechanical performance when considering reprocessing and a new life cycle of this conventional polymer.