Rohidas Bhoi
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Rohidas Bhoi has a total of 13 co-authors. Here are the top co-authors by number of shared publications:
Prathwiraj Meena
Department of Chemical Engineering, Malaviya National Institute of Technology, Jaipur, India
2 shared publications- Sanjay M. Mahajani
Indian Institute of Technology Bombay Powai
2 shared publications Suja George
Department of Chemical Engineering, Malaviya National Institute of Technology, Jaipur, India
2 shared publicationsSurabhi Singh
Department of Chemical Engineering, Malaviya National Institute of Technology, Jaipur, India
2 shared publicationsVirendra Kumar Saharan
Department of Chemical Engineering, Malaviya National Institute of Technology, Jaipur, India
2 shared publications- Ashish Unnarkat
Pandit Deendayal Energy University
1 shared publication
Latest Publications
- Open Access
- 23 April 2025
- Published by Elsevier in Next Sustainability
- Vol. 5
Thermodynamic and kinetic analysis of waste plastic pyrolysis: Synergistic effects and sustainability perspectives
- 23 April 2025
- Published by Elsevier in Next Sustainability
- Vol. 5
Open AccessThermodynamic and kinetic analysis of waste plastic pyrolysis: Synergistic effects and sustainability perspectives
- 3 November 2024
- Published by Springer Nature in Journal of Material Cycles and Waste Management
- Vol. 27 (1) , 19-33
Sustainable management of spent coffee grounds: applications, decompositions techniques and structural analysis
- 3 November 2024
- Published by Springer Nature in Journal of Material Cycles and Waste Management
- Vol. 27 (1) , 19-33
Sustainable management of spent coffee grounds: applications, decompositions techniques and structural analysis
- 15 February 2024
- Published by Springer Nature in Korean Journal of Chemical Engineering
- Vol. 41 (4) , 1055-1075
Enhanced Oil Yield by Catalytic Pyrolysis of Thermoplastics Using Cost-Effective Spent FCC and BaCO3 and Its Valorization to Gasoline and Diesel Grade Fuel via Fractionation
- 15 February 2024
- Published by Springer Nature in Korean Journal of Chemical Engineering
- Vol. 41 (4) , 1055-1075
Enhanced Oil Yield by Catalytic Pyrolysis of Thermoplastics Using Cost-Effective Spent FCC and BaCO3 and Its Valorization to Gasoline and Diesel Grade Fuel via Fractionation
- 11 November 2023
- Published by Springer Nature in Environmental Science and Pollution Research
- Vol. 31 (46) , 57430-57443
Performance, combustion, and emission characteristics of bio-oil produced by in situ catalytic pyrolysis of polypropylene using spent FCC
Plastic waste is a rich source of hydrocarbons that can be converted into bio-oil through pyrolysis. In this study, bio-oil was produced by pyrolysis of waste-polypropylene using spent FCC catalyst. Gas chromatography-mass spectrometry (GC–MS) analysis revealed that catalytically produced oil has the majority of compounds in the hydrocarbon range of C6–C18. The catalytic pyrolysis oil was blended with conventional fuel (diesel) to extensively investigate its suitability as a fuel substitute in a single-cylinder, four-stroke, 3.5 kW, diesel internal combustion (IC) engine. Furthermore, four fuels, i.e., CF100PO00 (pure diesel), CF90PO10 (10% v/v pyrolysis oil blended with diesel), CF85PO15 (15% v/v pyrolysis oil blended with diesel), and CF80PO20 (20% v/v pyrolysis oil blended with diesel), were tested in IC diesel engine for performance, combustion, and exhaust emission analysis at 1500 rpm. The tests were carried out at five loads, i.e., 1, 5, 10, 15, and 20 Nm. It was found that CF90PO10 produced 6.61% higher brake thermal efficiency (BTE), whereas CO2 exhaust emission decreased by 20% for CF80PO20 with respect to the pure diesel. Diesel blends with plastic pyrolysis oil can be a promising biofuel to improve engine performance and combustion characteristics without any significant engine modification.
- 11 November 2023
- Published by Springer Nature in Environmental Science and Pollution Research
- Vol. 31 (46) , 57430-57443
Performance, combustion, and emission characteristics of bio-oil produced by in situ catalytic pyrolysis of polypropylene using spent FCC
Plastic waste is a rich source of hydrocarbons that can be converted into bio-oil through pyrolysis. In this study, bio-oil was produced by pyrolysis of waste-polypropylene using spent FCC catalyst. Gas chromatography-mass spectrometry (GC–MS) analysis revealed that catalytically produced oil has the majority of compounds in the hydrocarbon range of C6–C18. The catalytic pyrolysis oil was blended with conventional fuel (diesel) to extensively investigate its suitability as a fuel substitute in a single-cylinder, four-stroke, 3.5 kW, diesel internal combustion (IC) engine. Furthermore, four fuels, i.e., CF100PO00 (pure diesel), CF90PO10 (10% v/v pyrolysis oil blended with diesel), CF85PO15 (15% v/v pyrolysis oil blended with diesel), and CF80PO20 (20% v/v pyrolysis oil blended with diesel), were tested in IC diesel engine for performance, combustion, and exhaust emission analysis at 1500 rpm. The tests were carried out at five loads, i.e., 1, 5, 10, 15, and 20 Nm. It was found that CF90PO10 produced 6.61% higher brake thermal efficiency (BTE), whereas CO2 exhaust emission decreased by 20% for CF80PO20 with respect to the pure diesel. Diesel blends with plastic pyrolysis oil can be a promising biofuel to improve engine performance and combustion characteristics without any significant engine modification.
- 4 March 2021
- Published by Elsevier in Materials Today: Proceedings
- Vol. 45, 5183-5189
Bimetallic catalyzed decomposition of hydrogen peroxide – Kinetics, effect of support and reaction medium
- 4 March 2021
- Published by Elsevier in Materials Today: Proceedings
- Vol. 45, 5183-5189
Bimetallic catalyzed decomposition of hydrogen peroxide – Kinetics, effect of support and reaction medium
- 14 March 2018
- Published by Royal Society of Chemistry (RSC) in Reaction Chemistry & Engineering
- Vol. 3 (2) , 171-181
Investigation of spontaneous emulsification and its relevance in biodiesel synthesis
Transesterification of triglycerides (TGs) is associated with the coexistence of two sparingly miscible liquid phases. In this study, the reaction is carried out in a batch reactor with independent stirring of both the phases by maintaining a flat interface. An initial delay period followed by a sudden rise in reaction rate is observed. The S-shaped TG conversion curve thus represents an in situ change in the rate-controlling step during the course of reaction. The intrinsic reaction is reasonably fast and the progress of the reaction, in the initial period, is strongly influenced by the speed of agitation and the interfacial area. A spontaneous emulsion is observed as the reaction proceeds, resulting in a sudden rise in the interfacial area, and hence, the reaction rate. We observed that the change in the compositions of the individual phases was responsible for a decrease in the interfacial tension. At a particular concentration of the individual phases, a spontaneous emulsion is realized, beyond which, the reaction becomes kinetically controlled. During this period, the reaction rate is independent of agitation speed. The experimental results in both the pre- and post-emulsion period are explained using an appropriate model. We demonstrate that an appropriate selection of the initial composition of the two phases in a conventional batch reactor can conveniently eliminate the initial delay due to diffusional limitations.
- 14 March 2018
- Published by Royal Society of Chemistry (RSC) in Reaction Chemistry & Engineering
- Vol. 3 (2) , 171-181
Investigation of spontaneous emulsification and its relevance in biodiesel synthesis
Transesterification of triglycerides (TGs) is associated with the coexistence of two sparingly miscible liquid phases. In this study, the reaction is carried out in a batch reactor with independent stirring of both the phases by maintaining a flat interface. An initial delay period followed by a sudden rise in reaction rate is observed. The S-shaped TG conversion curve thus represents an in situ change in the rate-controlling step during the course of reaction. The intrinsic reaction is reasonably fast and the progress of the reaction, in the initial period, is strongly influenced by the speed of agitation and the interfacial area. A spontaneous emulsion is observed as the reaction proceeds, resulting in a sudden rise in the interfacial area, and hence, the reaction rate. We observed that the change in the compositions of the individual phases was responsible for a decrease in the interfacial tension. At a particular concentration of the individual phases, a spontaneous emulsion is realized, beyond which, the reaction becomes kinetically controlled. During this period, the reaction rate is independent of agitation speed. The experimental results in both the pre- and post-emulsion period are explained using an appropriate model. We demonstrate that an appropriate selection of the initial composition of the two phases in a conventional batch reactor can conveniently eliminate the initial delay due to diffusional limitations.
- 15 August 2017
- Published by Royal Society of Chemistry (RSC) in Reaction Chemistry & Engineering
- Vol. 2 (5) , 740-753
Investigation of mass transfer limitations in simultaneous esterification and transesterification of triglycerides using a heterogeneous catalyst
The process for the production of biodiesel can be intensified significantly by employing heterogeneous catalysts that can tolerate free fatty acid in the feedstock. The synthesis of biodiesel was experimentally investigated in a fixed bed reactor using refined sunflower oil (triglyceride) and raw Jatropha oil (triglyceride with free fatty acid). A zinc-based catalyst was used in the form of cylindrical pellets of 6 mm in diameter and 8–10 mm in length. For the raw Jatropha oil, conversions greater than 90% were realized for both triglycerides and free fatty acids (FFAs), typically at 200 °C and a molar ratio of 6 : 1 (methanol : oil) for a residence time of 40 gcat ml−1 min. The experimental results for the refined oil in the fixed bed reactor (FBR) are explained using an appropriate model that incorporates both simplified kinetics and external mass transfer resistances at liquid–liquid and solid–liquid interfaces. The comparison of FBR results with those of the independent experiments in a spinning basket reactor, in the absence of external mass transfer limitations, shows that the intrinsic reaction is very fast. Hence, in the fixed bed reactor, mass transfer limitations especially at the liquid–liquid interface play an important role under the conditions employed. The rates in the case of refined sunflower oil are significantly lower compared to those of Jatropha oil, due to the presence of FFA, mono- and diglycerides in the latter.
- 15 August 2017
- Published by Royal Society of Chemistry (RSC) in Reaction Chemistry & Engineering
- Vol. 2 (5) , 740-753
Investigation of mass transfer limitations in simultaneous esterification and transesterification of triglycerides using a heterogeneous catalyst
The process for the production of biodiesel can be intensified significantly by employing heterogeneous catalysts that can tolerate free fatty acid in the feedstock. The synthesis of biodiesel was experimentally investigated in a fixed bed reactor using refined sunflower oil (triglyceride) and raw Jatropha oil (triglyceride with free fatty acid). A zinc-based catalyst was used in the form of cylindrical pellets of 6 mm in diameter and 8–10 mm in length. For the raw Jatropha oil, conversions greater than 90% were realized for both triglycerides and free fatty acids (FFAs), typically at 200 °C and a molar ratio of 6 : 1 (methanol : oil) for a residence time of 40 gcat ml−1 min. The experimental results for the refined oil in the fixed bed reactor (FBR) are explained using an appropriate model that incorporates both simplified kinetics and external mass transfer resistances at liquid–liquid and solid–liquid interfaces. The comparison of FBR results with those of the independent experiments in a spinning basket reactor, in the absence of external mass transfer limitations, shows that the intrinsic reaction is very fast. Hence, in the fixed bed reactor, mass transfer limitations especially at the liquid–liquid interface play an important role under the conditions employed. The rates in the case of refined sunflower oil are significantly lower compared to those of Jatropha oil, due to the presence of FFA, mono- and diglycerides in the latter.