Yadong Wu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Yadong Wu has a total of 67 co-authors. Here are the top co-authors by number of shared publications:
Hua Ouyang
School of Mechanical Engineering, Shanghai Jiao Tong University , Shanghai , 200240 , China
14 shared publicationsAnjenq Wang
6 shared publicationsJie Tian
School of Mechanical Engineering, Shanghai Jiao Tong University, Shanghai, China
6 shared publications- Hua Ouyang
School of Mechanical Engineering, Shanghai Jiao Tong University, Shanghai, PR China
4 shared publications Hairun Xie
Shanghai Jiao Tong University
3 shared publications- Tao Li
School of Mechanical Engineering, Shanghai Jiao Tong University, Shanghai, China
3 shared publications
Latest Publications
- 15 September 2026
- Published by Elsevier in Aerospace Science and Technology
- Vol. 180
Effects of axial slot casing treatment on a transonic axial compressor under water-ingestion conditions
- 15 September 2026
- Published by Elsevier in Aerospace Science and Technology
- Vol. 180
Effects of axial slot casing treatment on a transonic axial compressor under water-ingestion conditions
- Open Access
- 14 July 2026
- Published by Walter de Gruyter GmbH in International Journal of Turbo & Jet-Engines
Experimental study on the vibrational characteristics of mistuned axial compressor blades under different operating conditions
The vibrational characteristics of mistuned compressor blades were experimentally investigated using a blade tip timing (BTT) technique. Experiments were conducted on a single-stage axial compressor, focusing on two representative vibration mechanisms: rotating-stall-induced vibration near the stability limit and forced vibration excited by upstream aerodynamic disturbances. Under stall conditions, pronounced blade vibration was observed. Spectral analysis revealed a dominant low-frequency component in both blade-tip fluctuating pressure and blade vibration signals. As the rotational speed increased, the vibration amplitude grew monotonically, showing an approximately linear relationship between the average blade vibration amplitude and the normalized rotational speed. To investigate forced vibration behavior, a set of upstream spoilers was installed to introduce periodic aerodynamic excitation. Forced response tests were carried out at engine orders EO = 10 and EO = 12. The results show that mistuning leads to significant blade-to-blade variations in vibration amplitude. While the average vibration amplitude decreases with increasing engine order, the amplitude magnification factor increases, indicating enhanced response localization among mistuned blades. This study contributes to a better understanding of blade dynamic behavior under both rotating-stall–induced and forced vibration conditions and offers useful experimental insight for vibration assessment of compressor blades operating near stability limits.
- 14 July 2026
- Published by Walter de Gruyter GmbH in International Journal of Turbo & Jet-Engines
Open AccessExperimental study on the vibrational characteristics of mistuned axial compressor blades under different operating conditions
The vibrational characteristics of mistuned compressor blades were experimentally investigated using a blade tip timing (BTT) technique. Experiments were conducted on a single-stage axial compressor, focusing on two representative vibration mechanisms: rotating-stall-induced vibration near the stability limit and forced vibration excited by upstream aerodynamic disturbances. Under stall conditions, pronounced blade vibration was observed. Spectral analysis revealed a dominant low-frequency component in both blade-tip fluctuating pressure and blade vibration signals. As the rotational speed increased, the vibration amplitude grew monotonically, showing an approximately linear relationship between the average blade vibration amplitude and the normalized rotational speed. To investigate forced vibration behavior, a set of upstream spoilers was installed to introduce periodic aerodynamic excitation. Forced response tests were carried out at engine orders EO = 10 and EO = 12. The results show that mistuning leads to significant blade-to-blade variations in vibration amplitude. While the average vibration amplitude decreases with increasing engine order, the amplitude magnification factor increases, indicating enhanced response localization among mistuned blades. This study contributes to a better understanding of blade dynamic behavior under both rotating-stall–induced and forced vibration conditions and offers useful experimental insight for vibration assessment of compressor blades operating near stability limits.
- 6 January 2026
- Published by Elsevier in Aerospace Science and Technology
- Vol. 171
Impact of strut clocking on the secondary flows in an aggressive compressor transition duct
- 6 January 2026
- Published by Elsevier in Aerospace Science and Technology
- Vol. 171
Impact of strut clocking on the secondary flows in an aggressive compressor transition duct
- 22 November 2024
- Published by Wiley in Journal of Turbomachinery
- Vol. 147 (6) , 1-28
Numerical Investigation on the Influence of Wet Compression Aerodynamic Performance of Multi-Stage Transonic Compressor
In this paper, the gas–liquid two-phase flow in a multi-stage transonic compressor is numerically simulated based on the Euler–Lagrange method. The changes in wet compression aerodynamic characteristics of the compressor are investigated under various spraying conditions (droplet sizes and spraying rates). The results indicate that the compressor choking boundary moves to a smaller flowrate after spraying. Wet compression improves the efficiency of the compressor. The evaporation cooling effect of wet compression decreases the total temperature ratio and augments the specific power, resulting in an enhanced total pressure ratio. After the water droplets are injected into the compressor, due to the small rise of the airflow temperature in the upstream area, the evaporation cooling effect of droplets is weak. The negative effects of droplets lead to a reduction in the total pressure ratio of the first-stage compressor. As water droplets move downstream, the gradual increase in airflow temperature enhances the evaporation cooling effect, thereby improving the compressor performance. Water droplets migrate radially inside the compressor and gather toward the blade tip area, causing the gas phase mass flow inside the compressor to be redistributed in the radial direction. Wet compression enhances the capability of the rotor blades to perform work and airflow, leading to an increase in the airflow twist velocity.
- 22 November 2024
- Published by Wiley in Journal of Turbomachinery
- Vol. 147 (6) , 1-28
Numerical Investigation on the Influence of Wet Compression Aerodynamic Performance of Multi-Stage Transonic Compressor
In this paper, the gas–liquid two-phase flow in a multi-stage transonic compressor is numerically simulated based on the Euler–Lagrange method. The changes in wet compression aerodynamic characteristics of the compressor are investigated under various spraying conditions (droplet sizes and spraying rates). The results indicate that the compressor choking boundary moves to a smaller flowrate after spraying. Wet compression improves the efficiency of the compressor. The evaporation cooling effect of wet compression decreases the total temperature ratio and augments the specific power, resulting in an enhanced total pressure ratio. After the water droplets are injected into the compressor, due to the small rise of the airflow temperature in the upstream area, the evaporation cooling effect of droplets is weak. The negative effects of droplets lead to a reduction in the total pressure ratio of the first-stage compressor. As water droplets move downstream, the gradual increase in airflow temperature enhances the evaporation cooling effect, thereby improving the compressor performance. Water droplets migrate radially inside the compressor and gather toward the blade tip area, causing the gas phase mass flow inside the compressor to be redistributed in the radial direction. Wet compression enhances the capability of the rotor blades to perform work and airflow, leading to an increase in the airflow twist velocity.
- 24 January 2024
- Published by Springer Nature in Journal of Thermal Science
- Vol. 33 (2) , 602-610
Experimental and Numerical Investigation of Non-synchronous Blade Vibration Excitation in a Transonic Axial Compressor
- 24 January 2024
- Published by Springer Nature in Journal of Thermal Science
- Vol. 33 (2) , 602-610
Experimental and Numerical Investigation of Non-synchronous Blade Vibration Excitation in a Transonic Axial Compressor
- 21 August 2023
- Published by Springer Nature in Nature Nanotechnology
- Vol. 19 (1) , 77-84
Self-regulated underwater phototaxis of a photoresponsive hydrogel-based phototactic vehicle
Incorporating a negative feedback loop in a synthetic material to enable complex self-regulative behaviours akin to living organisms remains a design challenge. Here we show that a hydrogel-based vehicle can follow the directions of photonic illumination with directional regulation inside a constraint-free, fluidic space. By manipulating the customized photothermal nanoparticles and the microscale pores in the polymeric matrix, we achieved strong chemomechanical deformation of the soft material. The vehicle swiftly assumes an optimal pose and creates directional flow around itself, which it follows to achieve robust full-space phototaxis. In addition, this phototaxis enables a series of complex underwater locomotions. We demonstrate that this versatility is generated by the synergy of photothermofluidic interactions resulting in closed-loop self-control and fast reconfigurability. The untethered, electronics-free, ambient-powered hydrogel vehicle manoeuvres through obstacles agilely, following illumination cues of moderate intensities, similar to that of natural sunlight.
- 21 August 2023
- Published by Springer Nature in Nature Nanotechnology
- Vol. 19 (1) , 77-84
Self-regulated underwater phototaxis of a photoresponsive hydrogel-based phototactic vehicle
Incorporating a negative feedback loop in a synthetic material to enable complex self-regulative behaviours akin to living organisms remains a design challenge. Here we show that a hydrogel-based vehicle can follow the directions of photonic illumination with directional regulation inside a constraint-free, fluidic space. By manipulating the customized photothermal nanoparticles and the microscale pores in the polymeric matrix, we achieved strong chemomechanical deformation of the soft material. The vehicle swiftly assumes an optimal pose and creates directional flow around itself, which it follows to achieve robust full-space phototaxis. In addition, this phototaxis enables a series of complex underwater locomotions. We demonstrate that this versatility is generated by the synergy of photothermofluidic interactions resulting in closed-loop self-control and fast reconfigurability. The untethered, electronics-free, ambient-powered hydrogel vehicle manoeuvres through obstacles agilely, following illumination cues of moderate intensities, similar to that of natural sunlight.
- 18 August 2023
- Published by Elsevier in Aerospace Science and Technology
- Vol. 141
Large eddy simulation investigation of S-shaped intake distortion and swirl characteristics
- 18 August 2023
- Published by Elsevier in Aerospace Science and Technology
- Vol. 141
Large eddy simulation investigation of S-shaped intake distortion and swirl characteristics
- 5 June 2023
- Published by Springer Nature in Journal of Thermal Science
- Vol. 32 (4) , 1345-1356
Modal Analysis of Axial Compressor Tip Rotating Instability under Varying Operating Conditions
- 5 June 2023
- Published by Springer Nature in Journal of Thermal Science
- Vol. 32 (4) , 1345-1356
Modal Analysis of Axial Compressor Tip Rotating Instability under Varying Operating Conditions