Xianyang Yan
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Xianyang Yan has a total of 13 co-authors. Here are the top co-authors by number of shared publications:
- Chao Wang
Yankuang Energy Group Co., Ltd., Jining 273500, China
1 shared publication - Haichen Yin
Coal Industry Management Department, Shandong Energy Group Co., Ltd., Jinan 250014, China
1 shared publication - Hang Sun
Yankuang Energy Group Co., Ltd., Jining 273500, China
1 shared publication - Jianpeng Wang
State Key Laboratory of Mining Disaster Prevention and Control, Shandong University of Science and Technology, Qingdao 266590, China
1 shared publication - Lishuai Jiang
State Key Laboratory of Disaster Prevention and Ecology Protection in Open-pit Coal Mines, Shandong University of Science and Technology, Qingdao, China
1 shared publication - Long Yuan
College of Energy and Mining Engineering, Shandong University of Science and Technology, Qingdao, China
1 shared publication
Latest Publications
- Open Access
- 28 October 2025
- Published by MDPI AG in Applied Sciences
- Vol. 15 (21) , 11488
Comparative Study of Cross-System Microseismic Energy Calculation and Fusion Methods—A Case Study
Microseismic monitoring technology serves as a vital tool for assessing the stability of coal and rock masses. The precision of energy calculations and the ability to integrate data across different systems have a direct impact on the effectiveness of early warning systems for hazards such as rockburst. This study utilized the 6306 working face of Shandong Energy Group’s Dongtan Coal Mine as its experimental site to address data inconsistencies caused by variations in sensor responses, localization algorithms, and energy calculation methods among microseismic monitoring systems. Two microseismic monitoring platforms, designated as System A and System B, were deployed to conduct a comparative and integrative study of cross-system energy calculations. The optimization of sensor layout facilitated a comprehensive analysis of the differences between the two systems in terms of P-wave arrival times, amplitude–frequency characteristics, and localization accuracy. Results indicated that System A achieved significantly lower localization errors, with an average of 49 m, compared to System B’s average of 70 m. Substantial differences were also found in waveform amplitude and dominant frequency, with a correlation coefficient of only 0.59 between the two systems. To bridge these disparities, an energy calculation method based on the displacement gauge function was developed. By fitting a localized gauge function R(Δ) and incorporating empirical coefficients, the energy calculation outputs of both systems were harmonized. Validation experiments demonstrated that the linear correlation coefficient of energy calculations between Systems A and B increased to 0.977 under the new method, confirming its effectiveness for data unification. This research provides critical theoretical and technical guidance for integrating microseismic data across systems and establishing unified early warning standards, thus advancing the monitoring and prediction of dynamic hazards in mining environments.
- 28 October 2025
- Published by MDPI AG in Applied Sciences
- Vol. 15 (21) , 11488
Open AccessComparative Study of Cross-System Microseismic Energy Calculation and Fusion Methods—A Case Study
Microseismic monitoring technology serves as a vital tool for assessing the stability of coal and rock masses. The precision of energy calculations and the ability to integrate data across different systems have a direct impact on the effectiveness of early warning systems for hazards such as rockburst. This study utilized the 6306 working face of Shandong Energy Group’s Dongtan Coal Mine as its experimental site to address data inconsistencies caused by variations in sensor responses, localization algorithms, and energy calculation methods among microseismic monitoring systems. Two microseismic monitoring platforms, designated as System A and System B, were deployed to conduct a comparative and integrative study of cross-system energy calculations. The optimization of sensor layout facilitated a comprehensive analysis of the differences between the two systems in terms of P-wave arrival times, amplitude–frequency characteristics, and localization accuracy. Results indicated that System A achieved significantly lower localization errors, with an average of 49 m, compared to System B’s average of 70 m. Substantial differences were also found in waveform amplitude and dominant frequency, with a correlation coefficient of only 0.59 between the two systems. To bridge these disparities, an energy calculation method based on the displacement gauge function was developed. By fitting a localized gauge function R(Δ) and incorporating empirical coefficients, the energy calculation outputs of both systems were harmonized. Validation experiments demonstrated that the linear correlation coefficient of energy calculations between Systems A and B increased to 0.977 under the new method, confirming its effectiveness for data unification. This research provides critical theoretical and technical guidance for integrating microseismic data across systems and establishing unified early warning standards, thus advancing the monitoring and prediction of dynamic hazards in mining environments.
- Open Access
Influence Analysis and Stepwise Regression of Coal Mechanical Parameters on Uniaxial Compressive Strength Based on Orthogonal Testing Method
Uniaxial compressive strength (UCS) and peak strain (PS) are essential indices for studying the mechanical properties of coal and rock masses, and they are closely related to mechanical parameters such as the elastic modulus (E), Poisson’s ratio (υ), cohesion (C) and internal friction angle (Φ) of coal and rock masses. This study took the No. 2-1 coal seam of Zhaogu No. 2 Mine, in Henan Province, China, as the research object. An RMT-150B servo testing machine was used to test all mechanical parameters, including the E, υ, C and Φ of coal and rock masses. Based on the principle of orthogonal testing, Three Dimensions Fast Lagrangian Analysis of Continua (FLAC3D) was used to select E, υ, C, Φ, tensile strength (Rm) and dilation angle (Ψ) as initial participation factors. Using these six parameters and a five-level combination scheme (L25 (56)), the influence of coal mechanical parameters on UCS and PS was investigated, using the software SPSS for stepwise regression analysis, and a uniaxial pressure-resistant regression prediction equation was established. The research showed that, under uniaxial compression conditions, the main parameters controlling UCS of coal masses are C and Φ; conversely, the main parameters controlling PS are E and C. UCS and PS exhibit significant linear relationships with these main controlling parameters. Here, a stepwise regression prediction equation was established through reliability verification analysis using the main controlling parameters. This prediction method produces very small errors and a good degree of fit, thus allowing the rapid prediction of UCS. The precision of the stepwise regression model depends on the number of test samples, which can be increased in the later stages of a design project to further improve the precision of the projection model.
Open AccessInfluence Analysis and Stepwise Regression of Coal Mechanical Parameters on Uniaxial Compressive Strength Based on Orthogonal Testing Method
Uniaxial compressive strength (UCS) and peak strain (PS) are essential indices for studying the mechanical properties of coal and rock masses, and they are closely related to mechanical parameters such as the elastic modulus (E), Poisson’s ratio (υ), cohesion (C) and internal friction angle (Φ) of coal and rock masses. This study took the No. 2-1 coal seam of Zhaogu No. 2 Mine, in Henan Province, China, as the research object. An RMT-150B servo testing machine was used to test all mechanical parameters, including the E, υ, C and Φ of coal and rock masses. Based on the principle of orthogonal testing, Three Dimensions Fast Lagrangian Analysis of Continua (FLAC3D) was used to select E, υ, C, Φ, tensile strength (Rm) and dilation angle (Ψ) as initial participation factors. Using these six parameters and a five-level combination scheme (L25 (56)), the influence of coal mechanical parameters on UCS and PS was investigated, using the software SPSS for stepwise regression analysis, and a uniaxial pressure-resistant regression prediction equation was established. The research showed that, under uniaxial compression conditions, the main parameters controlling UCS of coal masses are C and Φ; conversely, the main parameters controlling PS are E and C. UCS and PS exhibit significant linear relationships with these main controlling parameters. Here, a stepwise regression prediction equation was established through reliability verification analysis using the main controlling parameters. This prediction method produces very small errors and a good degree of fit, thus allowing the rapid prediction of UCS. The precision of the stepwise regression model depends on the number of test samples, which can be increased in the later stages of a design project to further improve the precision of the projection model.