Masaki Kudo
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Masaki Kudo has a total of 26 co-authors. Here are the top co-authors by number of shared publications:
- Masashi Arita
Graduate School of Information Science and Technology, Hokkaido University, Sapporo, Hokkaido, Japan
3 shared publications - Junichiro Shiomi
Department of Mechanical Engineering, Graduate School of Engineering, The University of Tokyo, 7-3-1 Hongo, Bunkyo-ku, Tokyo 113-8656, Japan
2 shared publications Kouichi Hamada
Graduate School of Information Science and Technology
2 shared publications- Yasuo Takahashi
Hokkaido University
2 shared publications Yuuki Ohno
Graduate School of Information Science and Technology
2 shared publicationsBin Xu
Department of Mechanical Engineering, Graduate School of Engineering, The University of Tokyo, 7-3-1, Bunkyo-ku, Tokyo113-8656, Japan
1 shared publication
Latest Publications
- Open Access
- 1 October 2025
- Published by Springer Nature
- p. 155-192
Effect of Heat Exchange, Control and Suppression of Thermocapillary Convection
The effects of interfacial heat transfer on thermocapillary convection in liquid bridges of high Pr fluids placed in ground-based experiments are described in this chapter. Heat exchange due to convective and radiative heat transfer along the liquid bridge surface can sensitively affect the thermocapillary convection. Section 2 shows the effects of heating/cooling of the liquid bridge on the instability responsible for the transition from steady to oscillatory state of convection, while Sect. 3 focuses on the suppression and control of convection through the local surface heating of the liquid bridge. Section 4 deals with a full zone liquid bridge heated with a ring heater, where the thermocapillary convection which is driven by the thermal radiation from the ring heater can be controlled by the minimum heating power given by the second ring heater. The interfacial heat transfer also becomes important in microgravity as described in Sect. 6 of Chapter “Microgravity Experiments in Kibo Onboard the International Space Station.”
- 1 October 2025
- Published by Springer Nature
- p. 155-192
Open AccessEffect of Heat Exchange, Control and Suppression of Thermocapillary Convection
The effects of interfacial heat transfer on thermocapillary convection in liquid bridges of high Pr fluids placed in ground-based experiments are described in this chapter. Heat exchange due to convective and radiative heat transfer along the liquid bridge surface can sensitively affect the thermocapillary convection. Section 2 shows the effects of heating/cooling of the liquid bridge on the instability responsible for the transition from steady to oscillatory state of convection, while Sect. 3 focuses on the suppression and control of convection through the local surface heating of the liquid bridge. Section 4 deals with a full zone liquid bridge heated with a ring heater, where the thermocapillary convection which is driven by the thermal radiation from the ring heater can be controlled by the minimum heating power given by the second ring heater. The interfacial heat transfer also becomes important in microgravity as described in Sect. 6 of Chapter “Microgravity Experiments in Kibo Onboard the International Space Station.”
- 13 May 2025
- Published by Elsevier in Chemical Engineering Science
- Vol. 314
Response of unsteady thermocapillary convection to local heating at specific depths in a thin liquid film
- 13 May 2025
- Published by Elsevier in Chemical Engineering Science
- Vol. 314
Response of unsteady thermocapillary convection to local heating at specific depths in a thin liquid film
- Open Access
- 25 October 2022
- Published by American Chemical Society (ACS) in Nano Letters
- Vol. 22 (21) , 8406-8412
Enhanced High Thermal Conductivity Cellulose Filaments via Hydrodynamic Focusing
Nanocellulose is regarded as a green and renewable nanomaterial that has attracted increased attention. In this study, we demonstrate that nanocellulose materials can exhibit high thermal conductivity when their nanofibrils are highly aligned and bonded in the form of filaments. The thermal conductivity of individual filaments, consisting of highly aligned cellulose nanofibrils, fabricated by the flow-focusing method is measured in dried condition using a T-type measurement technique. The maximum thermal conductivity of the nanocellulose filaments obtained is 14.5 W/m-K, which is approximately five times higher than those of cellulose nanopaper and cellulose nanocrystals. Structural investigations suggest that the crystallinity of the filament remarkably influence their thermal conductivity. Smaller diameter filaments with higher crystallinity, that is, more internanofibril hydrogen bonds and less intrananofibril disorder, tend to have higher thermal conductivity. Temperature-dependence measurements also reveal that the filaments exhibit phonon transport at effective dimension between 2D and 3D.
- 25 October 2022
- Published by American Chemical Society (ACS) in Nano Letters
- Vol. 22 (21) , 8406-8412
Open AccessEnhanced High Thermal Conductivity Cellulose Filaments via Hydrodynamic Focusing
Nanocellulose is regarded as a green and renewable nanomaterial that has attracted increased attention. In this study, we demonstrate that nanocellulose materials can exhibit high thermal conductivity when their nanofibrils are highly aligned and bonded in the form of filaments. The thermal conductivity of individual filaments, consisting of highly aligned cellulose nanofibrils, fabricated by the flow-focusing method is measured in dried condition using a T-type measurement technique. The maximum thermal conductivity of the nanocellulose filaments obtained is 14.5 W/m-K, which is approximately five times higher than those of cellulose nanopaper and cellulose nanocrystals. Structural investigations suggest that the crystallinity of the filament remarkably influence their thermal conductivity. Smaller diameter filaments with higher crystallinity, that is, more internanofibril hydrogen bonds and less intrananofibril disorder, tend to have higher thermal conductivity. Temperature-dependence measurements also reveal that the filaments exhibit phonon transport at effective dimension between 2D and 3D.
- 4 October 2021
- Published by Springer Nature in Microgravity Science and Technology
- Vol. 33 (5) , 1-9
Comparative Analysis of PIV and CFD Results for Unsteady Thermocapillary Convection in Thin-film Liquids
- 4 October 2021
- Published by Springer Nature in Microgravity Science and Technology
- Vol. 33 (5) , 1-9
Comparative Analysis of PIV and CFD Results for Unsteady Thermocapillary Convection in Thin-film Liquids
- 14 September 2015
- Published by The Electrochemical Society in ECS Transactions
- Vol. 69 (10) , 299-309
(Invited) Visualization of Conductive Filament of ReRAM during Resistive Switching by in-situ TEM
Performance of in-situ-transmission electron microscopy (TEM) applied to analysis of the resistive random access memory (ReRAM) is reported. Recent progress of ReRAMs makes it indispensable to understand the resistive switching mechanism in order to guarantee the reliability of ReRAMs. Since the TEM provides a high resolution images of the nanostructure, in-situ TEM should be a powerful tool for the analysis if electrical characteristics of ReRAMs can be measured in the TEM. The two sample fabrication methods are applied to two different ReRAM devices. Switching characteristics, which are almost the same as those measured at the outside of TEM by the use of conventional ReRAM cells, are achieved together with clear images of formation and rupture of conductive filaments corresponding to the low and high resistance states. In addition, retention characteristics longer than 106 s, and SET/RESET pulse operation more than 100k times are confirmed during TEM observation. These results indicate that the in-situ TEM will be a powerful tool to analyze the reliability of ReRAMs.
- 14 September 2015
- Published by The Electrochemical Society in ECS Transactions
- Vol. 69 (10) , 299-309
(Invited) Visualization of Conductive Filament of ReRAM during Resistive Switching by in-situ TEM
Performance of in-situ-transmission electron microscopy (TEM) applied to analysis of the resistive random access memory (ReRAM) is reported. Recent progress of ReRAMs makes it indispensable to understand the resistive switching mechanism in order to guarantee the reliability of ReRAMs. Since the TEM provides a high resolution images of the nanostructure, in-situ TEM should be a powerful tool for the analysis if electrical characteristics of ReRAMs can be measured in the TEM. The two sample fabrication methods are applied to two different ReRAM devices. Switching characteristics, which are almost the same as those measured at the outside of TEM by the use of conventional ReRAM cells, are achieved together with clear images of formation and rupture of conductive filaments corresponding to the low and high resistance states. In addition, retention characteristics longer than 106 s, and SET/RESET pulse operation more than 100k times are confirmed during TEM observation. These results indicate that the in-situ TEM will be a powerful tool to analyze the reliability of ReRAMs.
- 1 June 2014
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-2
Real-time resistive switching of Cu/MoOx ReRAM observed in transmission electron microscope
Inner-structural changes of a Cu/MoOx ReRAM was observed by in-situ TEM during the resistive switching. We succeeded for the first time to observe the structure changes in the continuous multiple resistive switching cycles. Cu-rich filament was formed in the MoOx layer during the SET process with positive voltage to the Cu electrode, and disappeared by negative voltage in the RESET process. It was also confirmed that thick filaments were generated when the current compliance for the SET process was increased. The most meaningful phenomenon is that the position of the filament changed at each SET process.
- 1 June 2014
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-2
Real-time resistive switching of Cu/MoOx ReRAM observed in transmission electron microscope
Inner-structural changes of a Cu/MoOx ReRAM was observed by in-situ TEM during the resistive switching. We succeeded for the first time to observe the structure changes in the continuous multiple resistive switching cycles. Cu-rich filament was formed in the MoOx layer during the SET process with positive voltage to the Cu electrode, and disappeared by negative voltage in the RESET process. It was also confirmed that thick filaments were generated when the current compliance for the SET process was increased. The most meaningful phenomenon is that the position of the filament changed at each SET process.
- 1 April 2013
- Published by Elsevier in Thin Solid Films
- Vol. 533, 48-53
Preparation of resistance random access memory samples for in situ transmission electron microscopy experiments
- 1 April 2013
- Published by Elsevier in Thin Solid Films
- Vol. 533, 48-53
Preparation of resistance random access memory samples for in situ transmission electron microscopy experiments