Brandon McWilliams
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Brandon McWilliams has a total of 84 co-authors. Here are the top co-authors by number of shared publications:
- Rajiv Sharan Mishra
Center for Friction Stir Processing, Department of Materials Science and Engineering, University of North Texas, Denton, USA
4 shared publications - Clara Mock
DEVCOM Army Research Laboratory Aberdeen Proving Ground Maryland USA
3 shared publications Marko Knezevic
3 shared publications- Marko Knezevic
Department of Mechanical Engineering, University of New Hampshire, Durham, NH 03824, USA
3 shared publications - Abhishek Mehta
Department of Materials Science and Engineering, University of Central Florida, Orlando, USA
2 shared publications - Daniel Jonathan Savage
Los Alamos National Laboratory 12 , Los Alamos, New Mexico 87545
2 shared publications
Latest Publications
- Top Cited Papers
- 23 January 2025
- Published by Elsevier in Scripta Materialia
- Vol. 259
Columnar-to-equiaxed transition in laser fusion additive manufacturing
- 23 January 2025
- Published by Elsevier in Scripta Materialia
- Vol. 259
Top Cited PapersColumnar-to-equiaxed transition in laser fusion additive manufacturing
- 14 June 2024
- Published by Defense Technical Information Center (DTIC)
Mechanical Properties of Additively Manufactured AlSi10Mg with Respect to Build Orientation
Anisotropic material properties are common in additively manufactured metals due to the directional nature of the manufacturing process. Understanding the impact of mechanical properties with respect to build direction allows researchers and engineers to make informed decisions regarding part design and build orientation. These decisions can influence part performance and confidence, especially in critical applications. This work found that for additively manufactured AlSi10Mg using laser-powder bed fusion, the direction perpendicular to the direction of printing (horizontal) shows a 2 percent decrease in ultimate tensile strength compared to the direction aligned with the print direction (vertical); however, the strain at failure, elastic modulus, and yield stress increased by 53 percent, 15 percent, and 8 percent, respectively.
- 14 June 2024
- Published by Defense Technical Information Center (DTIC)
Mechanical Properties of Additively Manufactured AlSi10Mg with Respect to Build Orientation
Anisotropic material properties are common in additively manufactured metals due to the directional nature of the manufacturing process. Understanding the impact of mechanical properties with respect to build direction allows researchers and engineers to make informed decisions regarding part design and build orientation. These decisions can influence part performance and confidence, especially in critical applications. This work found that for additively manufactured AlSi10Mg using laser-powder bed fusion, the direction perpendicular to the direction of printing (horizontal) shows a 2 percent decrease in ultimate tensile strength compared to the direction aligned with the print direction (vertical); however, the strain at failure, elastic modulus, and yield stress increased by 53 percent, 15 percent, and 8 percent, respectively.
- Open Access
- 6 May 2024
- Published by Elsevier in Materials Science and Engineering: A
- Vol. 902
Identification of an affordable and printable metastable β Ti alloy with outstanding deformation behaviour for use in laser powder bed fusion
- 6 May 2024
- Published by Elsevier in Materials Science and Engineering: A
- Vol. 902
Open AccessIdentification of an affordable and printable metastable β Ti alloy with outstanding deformation behaviour for use in laser powder bed fusion
- 19 February 2024
- Published by Elsevier in Materials Science and Engineering: A
- Vol. 896, 146269
Fatigue strength of an ultra-high strength low alloy steel fabricated via laser powder bed fusion
- 19 February 2024
- Published by Elsevier in Materials Science and Engineering: A
- Vol. 896, 146269
Fatigue strength of an ultra-high strength low alloy steel fabricated via laser powder bed fusion
- 22 July 2023
- Published by Elsevier in Materials Letters
- Vol. 350
Additive manufacturing of Al18Co30Cr10Fe10Ni32 high entropy alloy by gas atomization and laser powder bed fusion
- 22 July 2023
- Published by Elsevier in Materials Letters
- Vol. 350
Additive manufacturing of Al18Co30Cr10Fe10Ni32 high entropy alloy by gas atomization and laser powder bed fusion