Daniel Carazo Álvarez
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Daniel Carazo Álvarez has a total of 21 co-authors. Here are the top co-authors by number of shared publications:
- Juan de Dios Carazo Alvarez
Universidad de Jaén
3 shared publications - Mahmoodul Haq
Department of Civil & Environmental Engineering Michigan State University East Lansing Michigan USA
2 shared publications - Maria Dolores La Rubia
Department of Chemical, Environmental and Materials Engineering, Campus Las Lagunillas, University of Jaén, 23071 Jaén, Spain
2 shared publications - Alberto García-Collado
Department of Mechanical and Mining Engineering, University of Jaen, EPS de Jaen, Campus Las Lagunillas, 23071 Jaen, Spain
1 shared publication Anyul Lopez Camacho
Smart Materials 3D ( Spain)
1 shared publicationAnyul López-Camacho
1 shared publication
Latest Publications
- 1 November 2024
- Published by UK Zhende Publishing Limited Company in DYNA Ingenieria e Industria
- Vol. 99 (6) , 622-628
CHARACTERIZATION OF POLYLACTIC ACID (PLA) MECHANICAL PROPERTIES IN 3D PRINTING: INSIGHTS FROM ADVANCED ANALYSIS TECHNIQUES AND PRINTING ORIENTATIONS
This research examines the mechanical characteristics of polylactic acid (PLA) using a variety of experimental approaches, including analyses of printing orientations and the application of advanced methodologies such as digital image correlation (DIC) for accurate assessment of deformation, along with scanning electron microscopy (SEM) to evaluate fracture properties. Tensile strength, flexural, impact strength, compressive and shear strength were characterized in detail, highlighting the critical impact of layer deposition direction. These findings provide valuable information for optimizing orientation selection in specific additive manufacturing contexts, emphasizing the need to address anisotropy in 3D printed materials engineering. Keywords: Polymer; PLA; 3D-print; industrial process; Digital Image Correlation (DIC).
- 1 November 2024
- Published by UK Zhende Publishing Limited Company in DYNA Ingenieria e Industria
- Vol. 99 (6) , 622-628
CHARACTERIZATION OF POLYLACTIC ACID (PLA) MECHANICAL PROPERTIES IN 3D PRINTING: INSIGHTS FROM ADVANCED ANALYSIS TECHNIQUES AND PRINTING ORIENTATIONS
This research examines the mechanical characteristics of polylactic acid (PLA) using a variety of experimental approaches, including analyses of printing orientations and the application of advanced methodologies such as digital image correlation (DIC) for accurate assessment of deformation, along with scanning electron microscopy (SEM) to evaluate fracture properties. Tensile strength, flexural, impact strength, compressive and shear strength were characterized in detail, highlighting the critical impact of layer deposition direction. These findings provide valuable information for optimizing orientation selection in specific additive manufacturing contexts, emphasizing the need to address anisotropy in 3D printed materials engineering. Keywords: Polymer; PLA; 3D-print; industrial process; Digital Image Correlation (DIC).
- Open Access
- 20 July 2024
- Published by Elsevier in Materials Letters
- Vol. 372
Antiviral properties of polylactic acid and nano-TiO2 for 3D printing
- 20 July 2024
- Published by Elsevier in Materials Letters
- Vol. 372
Open AccessAntiviral properties of polylactic acid and nano-TiO2 for 3D printing
- Open Access
- 27 February 2023
- Published by MDPI AG in Bioengineering
- Vol. 10 (3) , 297
Preliminary Study of the Bactericide Properties of Biodegradable Polymers (PLA) with Metal Additives for 3D Printing Applications
Plastic is a highly used material in various sectors. Due to its plentiful availability in the environment, microorganism surface contamination is a risk. The aim of this work is to achieve bactericidal capacity in plastics that reduces the microorganism’s colonization risk and, consequently, reduces the chances of having an infection with E. coli and Listeria monocytogenes bacteria. Using polylactic acid (PLA) as the polymeric matrix, mixtures in concentrations of metal additive of ions of silver (Ag) R148 and S254 in 1% and 2% have been studied and manufactured. The materials are developed on an industrial scale through a process that proceeds as follows: (I) a mixture of polymer and additive in a double-screw compounder to obtain the compound in different concentrations, (II) the manufacture of filaments with a single-screw extruder, (III) 3D printing parts. Therefore, materials are evaluated in the form of powder, pellets and printed pieces to ensure their antibacterial effectiveness throughout the manufacturing process. The results of the research show antibacterial effectiveness for E. coli and Listeria monocytogenes of metal additives and polymeric compounds for all manufacturing phases on an industrial scale, with the effectiveness for additive R148 predominating at a concentration of 2%, demonstrating its microbial efficacy on surfaces with potential application in medicine.
- 27 February 2023
- Published by MDPI AG in Bioengineering
- Vol. 10 (3) , 297
Open AccessPreliminary Study of the Bactericide Properties of Biodegradable Polymers (PLA) with Metal Additives for 3D Printing Applications
Plastic is a highly used material in various sectors. Due to its plentiful availability in the environment, microorganism surface contamination is a risk. The aim of this work is to achieve bactericidal capacity in plastics that reduces the microorganism’s colonization risk and, consequently, reduces the chances of having an infection with E. coli and Listeria monocytogenes bacteria. Using polylactic acid (PLA) as the polymeric matrix, mixtures in concentrations of metal additive of ions of silver (Ag) R148 and S254 in 1% and 2% have been studied and manufactured. The materials are developed on an industrial scale through a process that proceeds as follows: (I) a mixture of polymer and additive in a double-screw compounder to obtain the compound in different concentrations, (II) the manufacture of filaments with a single-screw extruder, (III) 3D printing parts. Therefore, materials are evaluated in the form of powder, pellets and printed pieces to ensure their antibacterial effectiveness throughout the manufacturing process. The results of the research show antibacterial effectiveness for E. coli and Listeria monocytogenes of metal additives and polymeric compounds for all manufacturing phases on an industrial scale, with the effectiveness for additive R148 predominating at a concentration of 2%, demonstrating its microbial efficacy on surfaces with potential application in medicine.
- 1 May 2022
- Published by UK Zhende Publishing Limited Company in DYNA Ingenieria e Industria
- Vol. 97 (3) , 254-257
EVALUATION OF THE MECHANICAL PROPERTIES AND MICROSTRUCTURE OF AISI 316L ALLOY SPECIMENS PRINTED BY FUSED FILAMENT FABRICATION
The additive manufacturing process by extrusion can provide an economical alternative to the manufacture of metal parts compared to powder bed fusion technologies, which are more expensive and with much lower production rates. The alternative’s viability is based on knowing how to print by extrusion metallic parts with adequate mechanical properties. This work explains how to print traction dog-bone specimens by fused fabrication of a filament loaded with stainless steel 316L powder. Subsequent, postprocesses of debinding and sintering for increasing specimen’s density are also described. The specimens were tested to assess the mechanical properties of traction achieved: elastic limit, youth modulus, maximum stress, rotational stress and Poisson's modulus. Finally, the results were compared with those obtained in an AISI 316L rolled steel specimen, and the obtained micro-structured was studied. Keywords: FFF, 316L, 3D printing, Sintering, Debinding.
- 1 May 2022
- Published by UK Zhende Publishing Limited Company in DYNA Ingenieria e Industria
- Vol. 97 (3) , 254-257
EVALUATION OF THE MECHANICAL PROPERTIES AND MICROSTRUCTURE OF AISI 316L ALLOY SPECIMENS PRINTED BY FUSED FILAMENT FABRICATION
The additive manufacturing process by extrusion can provide an economical alternative to the manufacture of metal parts compared to powder bed fusion technologies, which are more expensive and with much lower production rates. The alternative’s viability is based on knowing how to print by extrusion metallic parts with adequate mechanical properties. This work explains how to print traction dog-bone specimens by fused fabrication of a filament loaded with stainless steel 316L powder. Subsequent, postprocesses of debinding and sintering for increasing specimen’s density are also described. The specimens were tested to assess the mechanical properties of traction achieved: elastic limit, youth modulus, maximum stress, rotational stress and Poisson's modulus. Finally, the results were compared with those obtained in an AISI 316L rolled steel specimen, and the obtained micro-structured was studied. Keywords: FFF, 316L, 3D printing, Sintering, Debinding.
- Open Access
- 30 March 2020
- Published by Editorial CSIC in Revista de Metalurgia
- Vol. 56 (1) , e162
Influencia de la ubicación y orientación de muestras en las propiedades mecánica del acero estructural laminado en caliente: Reporte experimental
Para un modelado adecuado del comportamiento de las estructuras, es esencial una determinación precisa de las propiedades mecánicas del acero estructural. La caracterización mecánica debe satisfacer las prescripciones de las normas; en consecuencia, las muestras deben ser tomadas de una posición y orientación especifica; y las propiedades obtenidas de estos especímenes son usadas para caracterizar, de manera única, el acero. El proceso de laminado en caliente usado en la manufactura de perfiles de acero estructural, que implica la aparición de tensiones residuales, puede afectar a la homogeneidad e isotropía del producto final; por ello, la uniformidad de las propiedades mecánicas a lo largo de la sección no está garantizada. La variación de estas propiedades depende de la orientación y la locación y es estudiada en este artículo. Un programa de ensayos a tracción ha sido llevado a cabo, donde las curvas esfuerzo – deformación son registradas y usadas para obtener las propiedades mecánicas en condiciones elásticas y plásticas desde diferentes posiciones y orientaciones. No se encontraron trabajos experimentales similares en la literatura, excepto en el caso de acero conformado por doblado en frío. Los resultados no muestran diferencias significativas en la mayoría de casos; no obstante, las propiedades relacionadas con la estricción y falla muestran una clara dependencia con la ubicación. Las diferencias más importantes se hallaron en las muestras localizadas en el centro del ala; además, la investigación realizada denota que la orientación no influye en la variación de las propiedades mecánicas del acero laminado en caliente.
- 30 March 2020
- Published by Editorial CSIC in Revista de Metalurgia
- Vol. 56 (1) , e162
Open AccessInfluencia de la ubicación y orientación de muestras en las propiedades mecánica del acero estructural laminado en caliente: Reporte experimental
Para un modelado adecuado del comportamiento de las estructuras, es esencial una determinación precisa de las propiedades mecánicas del acero estructural. La caracterización mecánica debe satisfacer las prescripciones de las normas; en consecuencia, las muestras deben ser tomadas de una posición y orientación especifica; y las propiedades obtenidas de estos especímenes son usadas para caracterizar, de manera única, el acero. El proceso de laminado en caliente usado en la manufactura de perfiles de acero estructural, que implica la aparición de tensiones residuales, puede afectar a la homogeneidad e isotropía del producto final; por ello, la uniformidad de las propiedades mecánicas a lo largo de la sección no está garantizada. La variación de estas propiedades depende de la orientación y la locación y es estudiada en este artículo. Un programa de ensayos a tracción ha sido llevado a cabo, donde las curvas esfuerzo – deformación son registradas y usadas para obtener las propiedades mecánicas en condiciones elásticas y plásticas desde diferentes posiciones y orientaciones. No se encontraron trabajos experimentales similares en la literatura, excepto en el caso de acero conformado por doblado en frío. Los resultados no muestran diferencias significativas en la mayoría de casos; no obstante, las propiedades relacionadas con la estricción y falla muestran una clara dependencia con la ubicación. Las diferencias más importantes se hallaron en las muestras localizadas en el centro del ala; además, la investigación realizada denota que la orientación no influye en la variación de las propiedades mecánicas del acero laminado en caliente.
- 6 September 2012
- Published by Springer Nature
- p. 359-367
Photoelastic Testing and FE Analysis of T-Stub Model
- 6 September 2012
- Published by Springer Nature
- p. 359-367
Photoelastic Testing and FE Analysis of T-Stub Model
- 16 May 2011
- Published by Springer Nature
- p. 415-422
Experimental testing (2D DIC) and FE modeling of T-Stub Model
- 16 May 2011
- Published by Springer Nature
- p. 415-422
Experimental testing (2D DIC) and FE modeling of T-Stub Model