V. Goloborodko
Research Subjects
V. Goloborodko has a total of 9 co-authors. Here are the top co-authors by number of shared publications:
- S. Bekbossynov
Научно-производственный центр сельскохозяйственного машиностроения, Алматы, Казахстан
4 shared publications - Аскар Рзалиев
ТОО «Научно-производственный центр агроинженерии
4 shared publications - Sh. B. Bekmukhametov
Research and Production Center of Mechanical Engineering LLP, Kazakhstan
3 shared publications A. Rzaliyev
Research and Production Center of Mechanical Engineering LLP, Kazakhstan
2 shared publications- Ilyas Mizanbekov
НАО «Казахский национальный аграрный исследовательский университет
2 shared publications - B. Zhunusbaev
Research and Production Center of Mechanical Engineering LLP, Kazakhstan
1 shared publication
Latest Publications
- Open Access
- 30 June 2026
- Published by Kazakh National Agrarian University in Izdenister natigeler
- Vol. 28 (3 (111)) , 216-230
СЕЯЛКА ТОЧНОГО ВЫСЕВА ДЛЯ САХАРНОЙ СВЕКЛЫ, АДАПТИРОВАННАЯ К ПОЧ-ВЕННО-КЛИМАТИЧЕСКИМ УСЛОВИЯМ ЮЖНОЙ ЗОНЫ КАЗАХСТАНА
В условиях Юго-Востока Казахстана в конце марта происходит резкое повышение температуры воздуха, что приводит к иссушению поверхностного слоя почвы. В результате комки почвы в верхнем слое затвердевают, их твердость достигает 3 и более МПа и в дальнейшем они плохо поддаются крошению при обработке орудиями с пассивными рабочими органами. Вследствие этого фракционный состав почвы после весенних обработок не соответствует агротребованиям для посева семян. Разрыв во времени между предпосевной подготовкой почвы и посевом способствует иссушению почвы и задержке появления всходов. Кроме того часть семян остается на поверхности почвы. Предлагаемая сеялка высевает семена с шириной междурядий интервале 45,50,60см, проводит полосовую фрезерную обработку почвы в зоне посева, подготовку семенной борозды, включающую создание уплотненного семенного ложа. Теоретические исследования проводились в соответствии с классическими методами земледельческой механики, разработка конструкторской документации и испытания экспериментального образца проводились в соответствии с утвержденными ГОСТами и стандартами. Обоснованы параметры фрезерных рабочих органов сеялки-фрезы СТВ-2,4. Изготовлен экспериментальный образец и проведены его предварительные испытания, согласно которым фактическая глубина фрезерной обработки почвы соответствовала установочной 11,3см при среднем квадратическом отклонении (±σ )1,8 см и коэффициенте вариации (γ ) 15,9%. Содержание мелкокомковатой фракции почвы размером менее 20мм составляло 84,5%. Глубина заделки семян была стабильной в среднем 3,3см при ±σ = 0,63см и γ = 19%. Количество высеянных семян в рядке на 1 погонный метр составляло в среднем 4,7шт. при установочном 5шт.
- 30 June 2026
- Published by Kazakh National Agrarian University in Izdenister natigeler
- Vol. 28 (3 (111)) , 216-230
Open AccessСЕЯЛКА ТОЧНОГО ВЫСЕВА ДЛЯ САХАРНОЙ СВЕКЛЫ, АДАПТИРОВАННАЯ К ПОЧ-ВЕННО-КЛИМАТИЧЕСКИМ УСЛОВИЯМ ЮЖНОЙ ЗОНЫ КАЗАХСТАНА
В условиях Юго-Востока Казахстана в конце марта происходит резкое повышение температуры воздуха, что приводит к иссушению поверхностного слоя почвы. В результате комки почвы в верхнем слое затвердевают, их твердость достигает 3 и более МПа и в дальнейшем они плохо поддаются крошению при обработке орудиями с пассивными рабочими органами. Вследствие этого фракционный состав почвы после весенних обработок не соответствует агротребованиям для посева семян. Разрыв во времени между предпосевной подготовкой почвы и посевом способствует иссушению почвы и задержке появления всходов. Кроме того часть семян остается на поверхности почвы. Предлагаемая сеялка высевает семена с шириной междурядий интервале 45,50,60см, проводит полосовую фрезерную обработку почвы в зоне посева, подготовку семенной борозды, включающую создание уплотненного семенного ложа. Теоретические исследования проводились в соответствии с классическими методами земледельческой механики, разработка конструкторской документации и испытания экспериментального образца проводились в соответствии с утвержденными ГОСТами и стандартами. Обоснованы параметры фрезерных рабочих органов сеялки-фрезы СТВ-2,4. Изготовлен экспериментальный образец и проведены его предварительные испытания, согласно которым фактическая глубина фрезерной обработки почвы соответствовала установочной 11,3см при среднем квадратическом отклонении (±σ )1,8 см и коэффициенте вариации (γ ) 15,9%. Содержание мелкокомковатой фракции почвы размером менее 20мм составляло 84,5%. Глубина заделки семян была стабильной в среднем 3,3см при ±σ = 0,63см и γ = 19%. Количество высеянных семян в рядке на 1 погонный метр составляло в среднем 4,7шт. при установочном 5шт.
- Open Access
- 1 January 2026
- Published by FapUNIFESP (SciELO) in Brazilian Journal of Biology
- Vol. 86
Universal cultivator for shallow inter-row cultivation and deep loosening of sugar beet crops on compacted soils of Southern Kazakhstan
The article presents the results of the development and testing of a universal cultivator designed for shallow inter-row cultivation and deep loosening of sugar beet to a depth of up to 25 cm. On structureless and crust-prone soils of Southern Kazakhstan, soil hardness in sugar beet inter-rows reaches 3 MPa or higher during the second half of the growing season, while soil bulk density increases to 1.8-2.0 g/cm3 due to alternating irrigation events and high temperatures. Under these conditions, a surface soil crust forms in the inter-row space, restricting water infiltration and soil aeration. Achieving high sugar beet yields requires maintaining an optimal soil density within the root development zone. This can be accomplished through inter-row cultivation to a depth of up to 14 cm before row closure using a row-crop cultivator and through deep loosening to a depth of 23-25 cm after row closure in July and August, during the period of intensive root growth, as well as two weeks before harvest in September and October. Such a system of inter-row tillage reduces soil compaction, improves infiltration of irrigation water and precipitation, enhances gas exchange between soil layers, and consequently increases root yield. Deep loosening performed two weeks before harvest reduced root injury caused by the sugar beet harvester and decreased total harvesting losses. The novelty of the study lies in the selection and substantiation of the parameters of working bodies for deep inter-row loosening adapted to the specific conditions of sugar beet cultivation in Kazakhstan. An experimental prototype of the cultivator was manufactured and tested under field conditions. The implement provided an actual tillage depth corresponding to the preset depth within the range of 6-25 cm and maintained soil bulk density at 1.27-1.32 g/cm3. The highest root weight was obtained under the treatment involving two deep inter-row loosening operations. Compared with the control treatment (shallow inter-row cultivation), root weight increased by 24%. The same treatment also resulted in the lowest level of root damage during harvesting (5.2%). Commercial implementation of the universal cultivator can reduce the production costs of sugar beet cultivation and contribute to reducing the domestic sugar deficit in Kazakhstan.
- 1 January 2026
- Published by FapUNIFESP (SciELO) in Brazilian Journal of Biology
- Vol. 86
Open AccessUniversal cultivator for shallow inter-row cultivation and deep loosening of sugar beet crops on compacted soils of Southern Kazakhstan
The article presents the results of the development and testing of a universal cultivator designed for shallow inter-row cultivation and deep loosening of sugar beet to a depth of up to 25 cm. On structureless and crust-prone soils of Southern Kazakhstan, soil hardness in sugar beet inter-rows reaches 3 MPa or higher during the second half of the growing season, while soil bulk density increases to 1.8-2.0 g/cm3 due to alternating irrigation events and high temperatures. Under these conditions, a surface soil crust forms in the inter-row space, restricting water infiltration and soil aeration. Achieving high sugar beet yields requires maintaining an optimal soil density within the root development zone. This can be accomplished through inter-row cultivation to a depth of up to 14 cm before row closure using a row-crop cultivator and through deep loosening to a depth of 23-25 cm after row closure in July and August, during the period of intensive root growth, as well as two weeks before harvest in September and October. Such a system of inter-row tillage reduces soil compaction, improves infiltration of irrigation water and precipitation, enhances gas exchange between soil layers, and consequently increases root yield. Deep loosening performed two weeks before harvest reduced root injury caused by the sugar beet harvester and decreased total harvesting losses. The novelty of the study lies in the selection and substantiation of the parameters of working bodies for deep inter-row loosening adapted to the specific conditions of sugar beet cultivation in Kazakhstan. An experimental prototype of the cultivator was manufactured and tested under field conditions. The implement provided an actual tillage depth corresponding to the preset depth within the range of 6-25 cm and maintained soil bulk density at 1.27-1.32 g/cm3. The highest root weight was obtained under the treatment involving two deep inter-row loosening operations. Compared with the control treatment (shallow inter-row cultivation), root weight increased by 24%. The same treatment also resulted in the lowest level of root damage during harvesting (5.2%). Commercial implementation of the universal cultivator can reduce the production costs of sugar beet cultivation and contribute to reducing the domestic sugar deficit in Kazakhstan.
- Open Access
- 30 December 2025
- Published by Kazakh National Agrarian University in Izdenister natigeler
- No. 4 (108),p. 529-540
ТЕХНОЛОГИЧЕСКИЙ КОМПЛЕКС МАШИН ДЛЯ ВОЗДЕЛЫВАНИЯ И УБОРКИ САХАРНОЙ СВЕКЛЫ В УСЛОВИЯХ ЮГА, ЮГО-ВОСТОКА КАЗАХСТАНА
Проведен анализ имеющейся в хозяйствах техники для возделывания сахарной свеклы. В южной, юго-восточной зоне Казахстана сосредоточены почвы, подверженные иссушению, склонные к заплыванию и повышенной твердости. В результате традиционная технология возделывания сахарной свеклы в этих условиях не дает ожидаемого результата: оптимальную густоту стояния всходов, условия для роста растений и в конечном счете величину урожая, обеспечивающую окупаемость затрат и получение прибыли. Производство сахарной свеклы сосредоточено, в основном, в мелких и средних хозяйствах, которые в силу экономических причин не могут приобрести дорогостоящие почвообрабатывающие, посевные и свеклоуборочные агрегаты предлагаемые производителями зарубежных стран. Традиционная технология возделывания сахарной свеклы включает вспашку, несколько предпосевных рыхлений почвы, выравнивание, посев, междурядную обработку на глубину до 14см и уборку корнеплодов. При этом в результате разрыва во времени между технологическими операциями по обработке почвы и посеву происходит иссушение почвы. Кроме того, почвообрабатывающие орудия для предпосевной обработки с пассивными рабочими органами не обеспечивают необходимое крошение почвы для последующего качественного посева семян сахарной свеклы. В результате систематических поливов и высоких температур в июле, августе твердость почвы в междурядьях сахарной свеклы достигает высоких значений 3-4 МПА, что препятствует проникновению влаги к корням свеклы и газообмену. Серийно выпускаемые пропашные культиваторы обрабатывают междурядья на недостаточную глубину (12-14см). Степень травмированности корней сахарной свеклы имеющимися в хозяйствах свеклоуборочными комбайнами превышает допустимую вкличину. В связи с вышеизложенным, целью исследований является разработка технологического комплекса машин, обеспечивающего сокращение проходов машинно-тракторных агрегатов (МТА) по полю, сокращение разрыва во времени между технологическими операциями, высокое качество крошения почвы и посева семян, глубокую до 25см обработку междурядий сахарной свеклы, уборку корней свеклы с низкой повреждаемостью.
- 30 December 2025
- Published by Kazakh National Agrarian University in Izdenister natigeler
- No. 4 (108),p. 529-540
Open AccessТЕХНОЛОГИЧЕСКИЙ КОМПЛЕКС МАШИН ДЛЯ ВОЗДЕЛЫВАНИЯ И УБОРКИ САХАРНОЙ СВЕКЛЫ В УСЛОВИЯХ ЮГА, ЮГО-ВОСТОКА КАЗАХСТАНА
Проведен анализ имеющейся в хозяйствах техники для возделывания сахарной свеклы. В южной, юго-восточной зоне Казахстана сосредоточены почвы, подверженные иссушению, склонные к заплыванию и повышенной твердости. В результате традиционная технология возделывания сахарной свеклы в этих условиях не дает ожидаемого результата: оптимальную густоту стояния всходов, условия для роста растений и в конечном счете величину урожая, обеспечивающую окупаемость затрат и получение прибыли. Производство сахарной свеклы сосредоточено, в основном, в мелких и средних хозяйствах, которые в силу экономических причин не могут приобрести дорогостоящие почвообрабатывающие, посевные и свеклоуборочные агрегаты предлагаемые производителями зарубежных стран. Традиционная технология возделывания сахарной свеклы включает вспашку, несколько предпосевных рыхлений почвы, выравнивание, посев, междурядную обработку на глубину до 14см и уборку корнеплодов. При этом в результате разрыва во времени между технологическими операциями по обработке почвы и посеву происходит иссушение почвы. Кроме того, почвообрабатывающие орудия для предпосевной обработки с пассивными рабочими органами не обеспечивают необходимое крошение почвы для последующего качественного посева семян сахарной свеклы. В результате систематических поливов и высоких температур в июле, августе твердость почвы в междурядьях сахарной свеклы достигает высоких значений 3-4 МПА, что препятствует проникновению влаги к корням свеклы и газообмену. Серийно выпускаемые пропашные культиваторы обрабатывают междурядья на недостаточную глубину (12-14см). Степень травмированности корней сахарной свеклы имеющимися в хозяйствах свеклоуборочными комбайнами превышает допустимую вкличину. В связи с вышеизложенным, целью исследований является разработка технологического комплекса машин, обеспечивающего сокращение проходов машинно-тракторных агрегатов (МТА) по полю, сокращение разрыва во времени между технологическими операциями, высокое качество крошения почвы и посева семян, глубокую до 25см обработку междурядий сахарной свеклы, уборку корней свеклы с низкой повреждаемостью.
- Open Access
- 1 January 2025
- Published by FapUNIFESP (SciELO) in Brazilian Journal of Biology
- Vol. 85, e302109
Features of soil tillage in the Southern zone of Kazakhstan
Based on the results of the research, advanced soil tillage technologies and equipment have been developed for the cultivation of agricultural crops, aimed at preserving soil fertility and moisture. The objective of this study was to investigate erosion processes, agro-physical and hydrophysical parameters of light chestnut and sierozem soils under the influence of various types of tillage machine components, and to design machinery adapted to local soil conditions. With the participation of the article’s authors, several tools were developed: RCh-2.4 and RCh-4 chisel plows, and OKN-3.6 and OKP-4 combined implements. Field trials were conducted in both irrigated and rainfed agricultural zones of Kazakhstan to assess the impact of different tillage tools, including: the moldboard plow type PLN-4-35; sweep cultivator type KPS-4 for full-width tillage; flat shank cultivators type KPN-4; chisel cultivators type PCh-4 and RCh-2.4; and the combined implement OKN-3.6. The effectiveness of traditional vs. advanced soil tillage technologies was also evaluated.According to the study, the advanced technology resulted in erosion-prone particle content (fraction <1 mm) remaining below the critical threshold of 26%, while soil moisture reserves increased by 17%. In contrast, under the traditional technology, achieving an agronomically optimal soil structure required six passes of machine-tractor aggregates (MTA), whereas only two passes were needed with the advanced technology. The increased number of MTA passes under traditional practices extended the time required for spring fieldwork and led to further soil desiccation. The advanced technology developed in this study can be recommended for use across all soil types in the Republic of Kazakhstan.
- 1 January 2025
- Published by FapUNIFESP (SciELO) in Brazilian Journal of Biology
- Vol. 85, e302109
Open AccessFeatures of soil tillage in the Southern zone of Kazakhstan
Based on the results of the research, advanced soil tillage technologies and equipment have been developed for the cultivation of agricultural crops, aimed at preserving soil fertility and moisture. The objective of this study was to investigate erosion processes, agro-physical and hydrophysical parameters of light chestnut and sierozem soils under the influence of various types of tillage machine components, and to design machinery adapted to local soil conditions. With the participation of the article’s authors, several tools were developed: RCh-2.4 and RCh-4 chisel plows, and OKN-3.6 and OKP-4 combined implements. Field trials were conducted in both irrigated and rainfed agricultural zones of Kazakhstan to assess the impact of different tillage tools, including: the moldboard plow type PLN-4-35; sweep cultivator type KPS-4 for full-width tillage; flat shank cultivators type KPN-4; chisel cultivators type PCh-4 and RCh-2.4; and the combined implement OKN-3.6. The effectiveness of traditional vs. advanced soil tillage technologies was also evaluated.According to the study, the advanced technology resulted in erosion-prone particle content (fraction <1 mm) remaining below the critical threshold of 26%, while soil moisture reserves increased by 17%. In contrast, under the traditional technology, achieving an agronomically optimal soil structure required six passes of machine-tractor aggregates (MTA), whereas only two passes were needed with the advanced technology. The increased number of MTA passes under traditional practices extended the time required for spring fieldwork and led to further soil desiccation. The advanced technology developed in this study can be recommended for use across all soil types in the Republic of Kazakhstan.
- Open Access
- 12 February 2021
- Published by National Academy of Sciences of the Republic of Kazakshtan in Reports of the NAS RK
- Vol. 335 (1) , 132-139
SELECTION AND JUSTIFICATION OF PARAMETERS OF WORKING BODIES OF THE COMBINED TOOLS FOR THE BASIC AND PREPLANT PROCESSING OF SOIL IN THE CULTIVATION OF ROW CROPS IN THE CONDITIONS OF SOUTH KAZAKHSTAN
In the southern zone of Kazakhstan, agricultural crops are cultivated, both on irrigated and rain-fed lands. The main technology used for tillage is traditional, which accounts for 90% of all cultivated crops. This technology provides for multiple passes of machine-tractor units (MTU) across the field, which causes a large load on the soil, leading to the destruction of its structure. In the South of the Republic, combined tools supplied from neighboring countries (Russia, Belarus, Ukraine) are mainly used for pre-sowing tillage. They do not correspond to the soil and climate conditions and technologies used. To ensure the required quality of soil preparation, it is necessary to use machines adapted to zonal conditions. To develop a combined tool for pre-sowing and basic tillage, the parameters of its working bodies were justified. Based on the conducted research, a prototype of the combined OKP-4,0 machine was manufactured at the experimental plant of "SPC of agricultural engineering " LLP, and its acceptance tests were carried out during the operation of pre-sowing soil preparation for corn sowing, according to which the quality of soil treatment corresponded to agricultural requirements. There were no breakdowns or failures in operation.
- 12 February 2021
- Published by National Academy of Sciences of the Republic of Kazakshtan in Reports of the NAS RK
- Vol. 335 (1) , 132-139
Open AccessSELECTION AND JUSTIFICATION OF PARAMETERS OF WORKING BODIES OF THE COMBINED TOOLS FOR THE BASIC AND PREPLANT PROCESSING OF SOIL IN THE CULTIVATION OF ROW CROPS IN THE CONDITIONS OF SOUTH KAZAKHSTAN
In the southern zone of Kazakhstan, agricultural crops are cultivated, both on irrigated and rain-fed lands. The main technology used for tillage is traditional, which accounts for 90% of all cultivated crops. This technology provides for multiple passes of machine-tractor units (MTU) across the field, which causes a large load on the soil, leading to the destruction of its structure. In the South of the Republic, combined tools supplied from neighboring countries (Russia, Belarus, Ukraine) are mainly used for pre-sowing tillage. They do not correspond to the soil and climate conditions and technologies used. To ensure the required quality of soil preparation, it is necessary to use machines adapted to zonal conditions. To develop a combined tool for pre-sowing and basic tillage, the parameters of its working bodies were justified. Based on the conducted research, a prototype of the combined OKP-4,0 machine was manufactured at the experimental plant of "SPC of agricultural engineering " LLP, and its acceptance tests were carried out during the operation of pre-sowing soil preparation for corn sowing, according to which the quality of soil treatment corresponded to agricultural requirements. There were no breakdowns or failures in operation.
- 15 June 2020
- Published by National Academy of Sciences of the Republic of Kazakshtan in SERIES OF AGRICULTURAL SCIENCES
- Vol. 3 (57) , 51-58
COMBINED TOOLS FOR PRE-SOWING TILLAGE TO TRACTORS OF THE CLASS OF 14, 20 AND 30 KN
- 15 June 2020
- Published by National Academy of Sciences of the Republic of Kazakshtan in SERIES OF AGRICULTURAL SCIENCES
- Vol. 3 (57) , 51-58
COMBINED TOOLS FOR PRE-SOWING TILLAGE TO TRACTORS OF THE CLASS OF 14, 20 AND 30 KN