Frank Kameier
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Frank Kameier has a total of 6 co-authors. Here are the top co-authors by number of shared publications:
- Till M. Biedermann
University of Applied Sciences Duesseldorf, Duesseldorf, Germany
3 shared publications - Christian Oliver Paschereit
TU Berlin
1 shared publication - Nils Hintzen
Institute of Sound and Vibration Engineering ISAVE, University of Applied Sciences, D-40476 Dusseldorf, Germany
1 shared publication - Nils Hintzen
Institute of Sound and Vibration Engineering ISAVE, Faculty of Mechanical and Process Engineering, University of Applied Sciences Duesseldorf, Duesseldorf, Germany
1 shared publication - Pasquale Czeckay
Institute of Sound and Vibration Engineering ISAVE, University of Applied Sciences, D-40476 Dusseldorf, Germany
1 shared publication - Y. Moutamassik
Pollrich GmbH , Siegen/Moenchengladbach 41065 , Germany
1 shared publication
Latest Publications
- 22 May 2023
- Published by Wiley in Journal of Turbomachinery
- Vol. 145 (8) , 1-24
Assessment of the Impeller/Volute Relationship of Centrifugal Fans From an Aerodynamic and Aeroacoustic Perspective
Heavy-duty centrifugal fans require high reliability and first-class performance. Besides, extreme conditions and harsh environments are often encountered, such as in the papermaking process, in steel or cement plants or the chemical and petrochemical industry. Therefore, the design of high-performance heavy-duty industrial fans requires robust yet efficient solutions. The previous work indicates a high aerodynamic and aeroacoustic sensitivity concerning the specific position of the volute cutoff (tongue). This effect will be further investigated, not by directly changing the orientation of the cutoff, but by varying the position of the impeller relative to a fixed volute casing. The initial evaluation is done through a numerical study of three influencing parameters, which allow the aerodynamic dependencies to be modeled using low-layer artificial networks. Subsequently, extensive experimental studies were carried out to validate the aerodynamic dependencies and also to incorporate information on the aeroacoustic performance. The obtained results show that the operating point represents the key factor in determining the optimal positioning, with qualitatively comparable dependencies found for both tested fans. From an aeroacoustic point of view, the determined optimal configuration does not necessarily coincide with the observed aerodynamic desires, so careful analysis and a reasonable compromise are required, motivating for a multi-objective optimization process.
- 22 May 2023
- Published by Wiley in Journal of Turbomachinery
- Vol. 145 (8) , 1-24
Assessment of the Impeller/Volute Relationship of Centrifugal Fans From an Aerodynamic and Aeroacoustic Perspective
Heavy-duty centrifugal fans require high reliability and first-class performance. Besides, extreme conditions and harsh environments are often encountered, such as in the papermaking process, in steel or cement plants or the chemical and petrochemical industry. Therefore, the design of high-performance heavy-duty industrial fans requires robust yet efficient solutions. The previous work indicates a high aerodynamic and aeroacoustic sensitivity concerning the specific position of the volute cutoff (tongue). This effect will be further investigated, not by directly changing the orientation of the cutoff, but by varying the position of the impeller relative to a fixed volute casing. The initial evaluation is done through a numerical study of three influencing parameters, which allow the aerodynamic dependencies to be modeled using low-layer artificial networks. Subsequently, extensive experimental studies were carried out to validate the aerodynamic dependencies and also to incorporate information on the aeroacoustic performance. The obtained results show that the operating point represents the key factor in determining the optimal positioning, with qualitatively comparable dependencies found for both tested fans. From an aeroacoustic point of view, the determined optimal configuration does not necessarily coincide with the observed aerodynamic desires, so careful analysis and a reasonable compromise are required, motivating for a multi-objective optimization process.
- 16 September 2022
- Published by ASME International in Journal of Engineering for Gas Turbines and Power
- Vol. 144 (12)
Aeroacoustic Interactions of Blade Skew and Leading Edge Serrations Applied to Low-Pressure Axial Fans
Leading edge serrations are well known for their ability to reduce turbulence-induced noise of single aerofoils while also providing aerodynamic advantages under certain operating conditions. Continuatively, applying leading edge serrations to rotating machinery such as axial fans proved the validity to generally transfer the obtained aeroacoustic benefits of single aerofoils. However, for the rotating applications the noise reduction potential highly depends on the point of operation. The current work aims at assessing the aeroacoustic effects of serrated leading edges under the increased geometrical complexity of the fan blades through blade skew. Therefore, the question is whether combining two potentially effective noise-reducing treatments through blade skew and leading edge serrations results in leveraging or obstructing effects. By varying the skew angle from 0 deg to 38 deg, four different prototypes of the fan impeller are tested experimentally in a test rig according to ISO 5136 and ISO 5801. All configurations are tested with original blades of straight leading edges plus five sets of serrations each, parameterised by the serration amplitude and the serrations wavelength. The intensity of the incoming turbulence ranges from 2.6% to 12.1%. The results obtained show the skewed blades to improve both the aerodynamic performance and the noise radiation after exceeding an initial skew angle, complemented by a significant onset of stall. Moreover, no contraindication between blade skew and serrated leading edges is encountered, showing the potential to further extend the noise reduction capabilities by combining effects of blade skew and leading edge treatment.
- 16 September 2022
- Published by ASME International in Journal of Engineering for Gas Turbines and Power
- Vol. 144 (12)
Aeroacoustic Interactions of Blade Skew and Leading Edge Serrations Applied to Low-Pressure Axial Fans
Leading edge serrations are well known for their ability to reduce turbulence-induced noise of single aerofoils while also providing aerodynamic advantages under certain operating conditions. Continuatively, applying leading edge serrations to rotating machinery such as axial fans proved the validity to generally transfer the obtained aeroacoustic benefits of single aerofoils. However, for the rotating applications the noise reduction potential highly depends on the point of operation. The current work aims at assessing the aeroacoustic effects of serrated leading edges under the increased geometrical complexity of the fan blades through blade skew. Therefore, the question is whether combining two potentially effective noise-reducing treatments through blade skew and leading edge serrations results in leveraging or obstructing effects. By varying the skew angle from 0 deg to 38 deg, four different prototypes of the fan impeller are tested experimentally in a test rig according to ISO 5136 and ISO 5801. All configurations are tested with original blades of straight leading edges plus five sets of serrations each, parameterised by the serration amplitude and the serrations wavelength. The intensity of the incoming turbulence ranges from 2.6% to 12.1%. The results obtained show the skewed blades to improve both the aerodynamic performance and the noise radiation after exceeding an initial skew angle, complemented by a significant onset of stall. Moreover, no contraindication between blade skew and serrated leading edges is encountered, showing the potential to further extend the noise reduction capabilities by combining effects of blade skew and leading edge treatment.
- Open Access
Applicability of Aeroacoustic Scaling Laws of Leading Edge Serrations for Rotating Applications
The dominant aeroacoustic mechanisms of serrated leading edges, subjected to highly turbulent inflow conditions, can be compressed to spanwise decorrelation effects as well as effects of destructive interference. For single aerofoils, the resulting broadband noise reduction is known to follow spectral scaling laws. However, transferring serrated leading edges to rotating machinery, results in noise radiation patterns of significantly increased complexity, impeding to allocate the observed noise reduction to the underlying physical mechanisms. The current study aims at concatenating the scaling laws for stationary aerofoil and rotating-blade application and thus at providing valuable information on the aeroacoustic transferability of leading edge serrations. For the pursued approach, low-pressure axial fans are designed, obtaining identical serrated fan blade geometries than previously analyzed single aerofoils, hence allowing for direct comparison. Highly similar spectral noise reduction patterns are obtained for the broadband noise reduction of the serrated rotors, generally confirming the transferability and showing a scaling with the geometrical parameters of the serrations as well as the inflow conditions. Continuative analysis of the total noise reduction, however, constrains the applicability of the scaling laws to a specific operating range of the rotors and motivates for a devaluation of the scaling coefficients regarding additional rotor-specific effects.
Open AccessApplicability of Aeroacoustic Scaling Laws of Leading Edge Serrations for Rotating Applications
The dominant aeroacoustic mechanisms of serrated leading edges, subjected to highly turbulent inflow conditions, can be compressed to spanwise decorrelation effects as well as effects of destructive interference. For single aerofoils, the resulting broadband noise reduction is known to follow spectral scaling laws. However, transferring serrated leading edges to rotating machinery, results in noise radiation patterns of significantly increased complexity, impeding to allocate the observed noise reduction to the underlying physical mechanisms. The current study aims at concatenating the scaling laws for stationary aerofoil and rotating-blade application and thus at providing valuable information on the aeroacoustic transferability of leading edge serrations. For the pursued approach, low-pressure axial fans are designed, obtaining identical serrated fan blade geometries than previously analyzed single aerofoils, hence allowing for direct comparison. Highly similar spectral noise reduction patterns are obtained for the broadband noise reduction of the serrated rotors, generally confirming the transferability and showing a scaling with the geometrical parameters of the serrations as well as the inflow conditions. Continuative analysis of the total noise reduction, however, constrains the applicability of the scaling laws to a specific operating range of the rotors and motivates for a devaluation of the scaling coefficients regarding additional rotor-specific effects.